FA5527

FA5526/5527/5528/5536/5537/5538 Fuji Switching Power Control IC FA5526/5527/5528 FA5536/5537/5538 Application Note April.-2011 Fuji Electric Co., Ltd. Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 1 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 Warning 1. This Data Book contains the product specifications, characteristics, data, materials and structures as of April in 2011. The contents are subject to change without prior notice for specification changes or other reasons. When using a product listed in this Data Book, be sure to obtain the latest specifications and check the data. 2. All applications described in this Data Book give examples of applications of Fuji Electric’s products for your reference. No right or license, either express or implied, under any patent, copyright, trade secret or other intellectual property right owned by Fuji Electric Co., Ltd. shall be granted. 3. Although Fuji Electric Co., Ltd. continually strives to enhance product quality and reliability, a small percentage of semiconductor products may become faulty. When using Fuji Electric semiconductor products in your equipment, be sure to take adequate safety measures such as redundant, flame-retardant and fail-safe design in order to prevent a semiconductor product failure from leading to a physical injury, property damage or other problems. 4. The products introduced in this Data Book are intended for use in the following electronic and electrical equipment which requires ordinary reliability: ・Computers ・OA equipment ・Communications equipment (terminal devices) ・ Measurement equipment ・Machine tools ・Audiovisual equipment ・ Electrical home appliances ・Personal equipment ・Industrial robots, etc. 5. If you need to use a semiconductor product in this Data Book for equipment requiring higher reliability than normal, such as listed below, be sure to contact Fuji Electric Device Technology Co., Ltd. to obtain prior approval. When using these products, take adequate safety measures such as a backup system to prevent the equipment from malfunctioning when a Fuji Electric’s product incorporated in the equipment becomes faulty. ・Transportation equipment (mounted on vehicles and ships) ・Trunk communications equipment ・Traffic-signal control equipment ・Gas leakage detectors with an auto-shutoff function ・Disaster prevention / security equipment ・Safety devices 6. Do not use a product in this Data Book for equipment requiring extremely high reliability such as: ・Space equipment ・Airborne equipment ・Atomic control equipment ・Submarine repeater equipment ・Medical equipment 7. All rights reserved. No part of this Data Book may be reproduced without permission in writing from Fuji Electric Co., Ltd. 8. If you have any question about any portion of this Data Book, ask Fuji Electric Co., Ltd. or its sales agencies. Neither Fuji Electric Co., Ltd. nor its agencies shall be liable for any injury or damage caused by any use of the products not in accordance with instructions set forth herein. Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 2 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 Contents 1． Outline 2． Features 3． External dimension diagram 4． Block diagram 5． Pin assignments 6． Selection Guide of FA5526/27/28/36/37/38 series 7． Ratings and characteristics 8． Characteristic curves 9． Description of block circuits 10． Design advice 11． Examples of application circuits ・・・・・・・・ 4 ・・・・・・・ ・・・・・・・・ 4 ・・・・・・・ ・・・・・・・・ 4 ・・・・・・・ ・・・・・・・・ 5 ・・・・・・・ ・・・・・・・・ 5 ・・・・・・・ ・・・・・・・・ 6 ・・・・・・・ ・ ・ ・ ・ ・ ・ ・ ・ 6 to 9 ・・・・・・・ ・ ・ ・ ・ ・ ・ ・ ・ 10 to 14 ・・・・・・・ ・ ・ ・ ・ ・ ・ ・ ・ 15 to 24 ・・・・・・・ ・ ・ ・ ・ ・ ・ ・ ・ 25 to 32 ・・・・・・・ ・ ・ ・ ・ ・ ・ ・ ・ 33 ・・・・・・・ Note） ・ The contents of this Data Book are subject to change without prior notice for improvement or other reasons. ・ Application examples and parts constants listed in this Data Book are intended for design reference, without giving due consideration to unevenness in parts characteristics and usage conditions. When using, be sure to design the relevant circuit giving due consideration to unevenness in parts characteristics and usage conditions. Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 3 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 1. Outline FA5526/27/28/36/37/38 series are current-mode switching power control ICs that can directly drive power MOSFETs. Low-power dissipation is achieved due to adoption of high break-down voltage CMOS process. In addition, stand-by power consumption can substantially be reduced due to a built-in start-up circuit. Many functions are incorporated in an eight pin package, reducing the number of external parts and allowing compact and high cost performance power supply 2. Features ▪ Built-in start-up circuit of 500V break-down voltage that is cut off after start-up (input current after cutoff: 25µA (typ.)) ▪ Low power dissipation due to adoption of high break-down voltage CMOS process Supply Current in Operating Mode : 1.4mA (typ.) ▪ Built-in frequency-decreasing function at light load ▪ Oscillating frequency FA5526/5536 : 130kHz(typ.), FA5527/5537 : 100kHz(typ.), FA5528/5538 : 60kHz(typ.) ▪ Built-in latch-mode cutoff function of overload ( over current ) for FA5526/5527/5528 ▪ Built-in Auto-Recovery cutoff function of overload ( over current ) for FA5536/5537/5538 ▪ Built-in latch-mode cutoff function of over-voltage for 28V(typ.) at VCC pin for FA5526/5527/5528. ▪ Built-in Auto-Recovery-mode cutoff function of over-voltage for 28V(typ.) at VCC pin for FA5536/5537/5538. ▪ Built-in Under Voltage Lock-Out for VCC pin (15V : ON, 9V : OFF) ▪ 8 pins package(DIP / SO) ( for FA5528 and FA5538 ) 3. External dimension diagram Unit：mm SO-8 （FA5526N/27N/28N/36N/37N/38N） DIP-8 （FA5526P/27P/28P/36P/37P/38P） 0° 8 5 -8 ° 8 5 3 .9 ± 0 . 1 6 .0 ±0 .2 0 .6 5 ± 0 .2 5 1 4 9.4 1.0±0.3 1.5±0.3 3 M IN 4 . 5 M A X 1 4 4.9±0.1 0 .2 0 3 .4 0 .1 8 ± 0 . 0 8 6.5 0 .2 5 1 .7 M A X + 0 .1 /- 0 . 0 5 2.54 0.5±0.1 0 -1 5° 7.6 1.27 0.40±0.1 2.54×3=7.62 Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 4 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 4. Block diagram 5V reg VCC 5V ENB UVLO Latch CS (1) 11µA/4µA 1.3mA OVP off START 28V UVLO 30V 15V/9V ENB VH (8) VCC (6) 8.5V/7.9V 0.68V 4.8V Buf x1 Q T 3R R 4.0V/3.5V 2.9V 7.4k OverLoad FB (2) 1Meg 5pF OSC VCO Blanking 1 shot TRG Q CLR S Q RQ F.F. IS comp. 0.52V IS (3) OUT (5) OUT PUT 60k 20k 0.28V SLOPE GENERATOR +Σ GND (4) FA5526 / FA5527 / FA5528 for Timer Latched OCP CS (1) 5V reg VCC 5V ENB UVLO Auto-Recovery 11µA/4µA 1.3mA OVP off START 28V UVLO 30V 15V/9V ENB VH (8) VCC (6) 8.5V/7.9V 0.68V 4.8V Buf x1 Q T 3R R 4.0V/3.5V 2.9V 7.4k OverLoad FB (2) 1Meg 5pF OSC VCO Blanking 1 shot TRG Q CLR S Q RQ F.F. IS comp. 0.52V IS (3) OUT (5) OUT PUT 60k 20k 0.28V SLOPE GENERATOR +Σ GND (4) FA5536 / FA5537 / FA5538 for Auto-Recovery OCP 5. Pin assignments Pin 1 2 3 4 5 6 7 8 Symbol CS FB IS GND OUT VCC (NC) VH Function Soft start/latch-mode stop Feedback input Current sensor input Ground Output Power supply No connection High voltage input Description Time Setting of Soft start and Over Current Protection Input for controlling current comparator threshold voltage Input for monitoring MOSFET current Power supply ground Output for directly driving a MOSFET Power supply for ICs No connection Input terminal for start-up circuit Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 5 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 6. Line-up of FA5526/27/28/36/37/38 series Type FA5526P/N FA5527P/N FA5528P/N FA5536P/N FA5537P/N FA5538P/N Switching Frequency (kHz) 130 (typ.) 100 (typ.) 60 (typ.) 130 (typ.) 100 (typ.) 60 (typ.) Over Current Protection Latch with adjustable delay time Latch with adjustable delay time Latch with adjustable delay time Auto-Recovery Auto-Recovery Auto-Recovery Package DIP-8/SO-8 DIP-8/SO-8 DIP-8/SO-8 DIP-8/SO-8 DIP-8/SO-8 DIP-8/SO-8 7. Ratings and characteristics ＊In defining a current, “＋” represents a sink current and “－” a source current. (1) Absolute maximum ratings Item Supply voltage Low impedance source (Icc>15mA) Built-in Zener clamp (Icc Vccon VH pin = 100V, Vcc = 0V VH pin = 100V Vcc = 10V, VH pin = 100V at start-up or protection mode ( OCP, OVP ) Vcc = 13V, VH pin = 100V at start-up or protection mode ( OCP, OVP ) MIN 12 TYP 25 7.0 23 MAX 37 Unit uA mA V Ipre1 VCC pin charging current Ipre2 -6.6 -4.0 mA -6.5 -3.5 mA Consumption current (VCC pin) Item Symbol Condition Duty cycle = DMAX, FB pin =3V, no load FA5526/36 FA5527/37 FA5528/38 MIN TYP 1.6 1.5 1.4 1.6 290 30 MAX 2.4 2.2 2.0 2.4 400 mA uA V mA Unit Supply current during operation ICCOP1 ICCOP2 Consumption current in latch mode Zener voltage ICCL Vz Duty cycle = 0％, FB pin = 0V FB pin, CS pin : open Iz = 2mA Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 9 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 8. Characteristic curves ・Unless otherwise specified, Ta=25℃, Vcc=18V ・In defining a current, “+” represents a sink current and “-” a source current. ・The data stated in this chapter are intended for giving typical IC characteristics and not for guaranteeing performance. Variation Ratio of Switching Frequency (delta fosc) vs. VCC pin voltage (Vcc) Variation Ratio of Switching Frequency (delta fosc) vs. Junction Temperature (Tj) 2 1.5 delta fosc (%) 2 1.5 d e l ta fo s c ( % ) 1 0.5 0 -0.5 -1 -1.5 -2 1 0.5 0 -0.5 -1 -1.5 -2 10 15 20 Vcc (V) 25 30 -40 -20 0 20 40 60 80 100 120 140 Tj (degree) Switching Frequency (fosc) vs. FB pin voltage 140 120 100 FA5526 / 36 Minimum Switching Frequency (fmin) vs. Junction Temperature (Tj) 2.0 1.5 fmin (kHz) FA5527 / 37 fosc (kHz) 80 60 FA5528 / 38 40 20 0 0 0.5 1 1.5 VFB (V) 1.0 0.5 0.0 2 2.5 3 -40 -20 0 20 40 60 80 100 120 140 Tj（degree） Maximum Duty Cycle (Dmax) vs. Junction Temperature (Tj) Minimum ON Width (Tmin) vs. Junction Temperature (Tj) 81.0 80.5 D max (% ) Tmin (ns) 800 700 600 500 400 FA5528 / 38 FA5527 / 37 80.0 79.5 FA5526 / 36 300 79.0 -40 -20 0 20 40 60 80 100 120 140 Tj（degree） 200 -40 -20 0 20 40 60 80 100 120 140 Tj（degree） Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 10 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 CS pin source current (Ics) vs. Junction Temperature (Tj) CS pin source current (Ics) vs. Junction Temperature (Tj) -9 CS=0V -3.5 CS=4V -10 -4 Ics (uA) -4.5 -5 -5.5 -6 Ics (uA) -11 -12 -13 -14 -40 -20 0 20 40 60 80 100 120 140 Tj （degree） -40 -20 0 20 40 60 80 100 120 140 Tj （degree) CS pin current (Ics) vs. CS pin voltage (Vcs) CS pin current (Ics) vs. CS pin voltage (Vcs) 80 70 FB=open 60 50 40 30 20 10 0 -10 -20 0 2 80 70 60 50 40 30 20 10 0 -10 -20 0 FB=3V 4 6 Vcs (V) 8 10 12 Ics (uA) Ics (uA) 2 4 6 Vcs (V) 8 10 12 UVLO ON threshold voltage (Vccon) vs. Junction Temperature (Tj) UVLO OFF threshold voltage (Vccoff) vs. Junction Temperature (Tj) 16.0 15.8 15.6 15.4 15.2 15.0 14.8 14.6 14.4 14.2 14.0 -40 -20 0 20 40 60 80 Tj (degree) 100 120 140 10.0 9.8 9.6 9.4 9.2 9.0 8.8 8.6 8.4 8.2 8.0 -40 -20 0 20 40 60 80 100 120 140 Tj (degree) Vccon (V) Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 11 http://www.fujielectric.co.jp/products/semiconductor/ Vccoff (V) FA5526/5527/5528/5536/5537/5538 OUT pin High Output Voltage (VOH) vs. VCC pin Voltage (Vcc) OUT pin Low Output Voltage (VOL) vs. VCC pin Voltage (Vcc) 3 IOH = -100mA 2.5 V c c - V O H (V ) 0.8 IOL = 100mA 0.7 V O L (V ) 0.6 0.5 0.4 0.3 10 15 20 Vcc (V) 25 30 2 1.5 1 10 15 20 Vcc (V) 25 30 IS pin maximum input threshold volatge(Vthis1) vs. Junction Temerature (Tj) IS pin input threshold voltage (Vthis) vs. FB pin voltage (VFB) 0.53 0.52 V th is 1 (V ) 0.51 0.50 0.49 0.48 0.47 -40 -20 0 20 40 60 80 100 120 140 Tj (degree) V th is (V ) 0.6 Duty cycle = 50% 0.5 0.4 0.3 0.2 0.1 0 0 1 2 VFB (V) 3 4 FB pin source current (IFB) vs. FB pin voltage (VFB) Threshold Voltage of Over-Voltage Protection (Vthvcc) vs. Junction Temperature (Tj) 0 -100 30.0 29.5 29.0 Vthvcc (V) 0 1 2 VFB (V) 3 4 5 -200 I FB (uA) -300 -400 -500 -600 28.5 28.0 27.5 27.0 26.5 26.0 -40 -20 0 20 40 60 80 100 120 140 Tj (degree) Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 12 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 Start-up Circuit VCC pin Source Current (Ipre) vs. VCC pin voltage (Vcc) Start-up Circuit VCC pin Source Current (Ipre) vs. Junction Temperature (Tj) -5.0 VVH = 100V -5.5 -6.0 Ip r e ( m A ) Ipre (mA) -5.5 -6.0 -6.5 -7.0 -7.5 -8.0 VVH = 100V Vcc = 0V -6.5 -7.0 -7.5 -8.0 0 5 Vcc (V) 10 15 -40 -20 0 20 40 60 80 Tj （degree) 100 120 140 Start-up Circuit VCC pin Source Current vs. VH pin voltage (VVH) IS pin threshold voltage (Vthis) vs. Duty Cycle at FB pin = 4V and CS pin = 4V -6 -6.2 Vcc = 0V -6.4 Ip re (m A ) -6.6 -6.8 -7 -7.2 -7.4 0 100 200 300 400 500 VVH (V) V th is (V ) 0.60 FB=4V CS=4V 0.55 0.50 0.45 0.40 0 10 20 30 40 D (%) 50 60 70 80 IS pin threshold voltage (Vthis) vs. Duty Cycle(D) at FB pin = 3V for FA5528/5538 IS pin threshold voltage (Vthis) vs. DutyCycle(D) at FB pin = 2V for FA5528/5538 0.50 FB=3V 0.45 V t h is ( V ) 0.30 FB=2V 0.25 V t h is ( V ) 0 10 20 30 40 D (%) 50 60 70 80 0.40 0.20 0.35 0.15 0.30 0.10 0 10 20 30 40 D (%) 50 60 70 80 Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 13 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 Operating Mode Supply Current vs. VCC pin voltage (Vcc) Operating Mode Supply Current (Iccop1) vs. Junction Temperature (Tj) 1.7 FA5526 / 36 1.7 FA5526 / 36 1.6 Iccop1 (mA) Iccop1 (mA) FA5527 / 37 1.5 FA5528 / 38 1.4 1.6 FA5527 / 37 1.5 FA5528 / 38 1.4 1.3 10 15 20 Vcc (V) 1.3 25 30 -40 -20 0 20 40 60 80 100 120 140 Tj (degree) Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 14 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 9. Description of block circuits (1) Start-up circuit The FA5526/27/28/36/37/38 has built-in start-up circuits with maximum rated voltage of 500V. Wiring is shown in Figs.1 to 3. When power is turned on, a current is supplied to the VCC pin from the start-up circuit, charging the capacitor, C2, connected to the VCC pin, increasing its voltage, activating the IC, and the power supply starts operation. The current supplied to the VCC pin from the VH pin is approximately 6.8mA at Vcc=0V, decreases as Vcc increases and becomes approximately 6.1mA at the start-up voltage. A resistor is connected in series to the VH pin to prevent the IC from being damaged due to surge in AC and other lines. Fig.1 shows the commonest wiring, connecting the VH pin to half-wave rectified AC input voltage and taking the longest start-up time of the three ways of wiring. When AC input voltage is turned off after the circuit changed to a latch mode due to overload or overvoltage protection, the latch mode can be reset in a relatively short time of several seconds because a current is not supplied from the VH pin. In Fig.2, the VH pin is connected to full-wave rectified AC input voltage, reducing start-up time to approximately half as compared to half-wave rectification circuit shown in Fig.1. The latch mode can be reset in a short time same as in Fig.1 because AC input voltage is cut off. In Fig.3, the VH pin is connected to rectified and smoothed AC input voltage, resulting in the shortest start-up time of the three ways of wiring. In this way of wiring, it takes time for the latch mode to be reset because charged C1 voltage is applied to the VH pin even if the IC have changed to the latch mode. Depending on usage conditions, in general it takes several minutes. When VCC pin voltage exceeds ON threshold voltage of the low-voltage malfunction-protective circuit input current becomes 25uA (typ.). When IC enters to the latch mode due to any abnormal condition, the start-up circuit is activated again, the latch condition is maintained and Vcc voltage is held at approximately 23V. Here, FA5526/27/28 enters to the latch mode by overload or over-voltage, but FA5536/37/38 does not enter to the latch mode without an additional external circuit (See “9.-(8)/(9) Overload protection,” “9.-(10)/(11) Over-voltage 15 http://www.fujielectric.co.jp/products/semiconductor/ protection.” ). Fig.1 Start-up circuit 1 (half wave) Fig.2 Start-up circuit 2 (full wave) and the IC is activated, the start-up circuit is cut off and VH pin Fig.3 Start-up circuit 3 (DC) Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 FA5526/5527/5528/5536/5537/5538 (2) Oscillator The oscillator determines switching frequency. For steady operation at heavy load, the oscillating frequency is set at 130kHz for FA5526/36, 100kHz for FA5527/37 or 60kHz for FA5528/38 inside the IC. In addition, the IC has a function to automatically decrease oscillating frequency at light load to reduce standby power dissipation. When FB pin voltage becomes 1.05V or less at light load, the frequency starts decreasing. At light load, as FB pin voltage drops, the frequency decreases almost linearly to the minimum operating frequency (Fig.4). The minimum operating frequency, Fmin, is set at 1.1kHz. The oscillator generates a trigger signal for Fig.4 Oscillating frequency determining the switching frequency, a pulse signal for determining the maximum duty cycle and a ramp signal for slope compensation. C1 OSC Blanking Rs (3) Current comparator and PWM latch FA5526/27/28/36/37/38 have current mode IS comp. comparators. Fig.5 shows a block diagram for basic operation and Fig.6 a timing chart. A trigger signal is generated by the oscillator and input to the PWM latch (F.F.) as a set signal through a blanking circuit, increasing PMW latch output and also OUT pin voltage. On the other hand, the current comparator (IS comp.) monitors a MOSFET current and generates a reset signal when OUT pin voltage reaches the threshold voltage. Then, PWM latch (F.F.) output and OUT pin voltage go into low state The output is controlled through varying IS comparator threshold voltage due to a feedback signal. As shown in Fig.7, FB pin voltage and CS pin voltage are level-shifted and input to the current comparator (IS comp.) as threshold voltage. In addition, the reference voltage of 0.52V is input to the IC to determine IS pin maximum threshold voltage. The lowest of the three inputs is given a high priority. IS comp. Output (reset pulse) Flip Flop ( F.F. ) “Q” output ( OUT pin signal ) Blanking Output Signal (set pulse) SQ R F.F. 5 OUT 3 Fig.5 IS Current-mode basic operation circuit block IS pin Voltage proportional to Drain Current of MOSFET “Q1” IS comp. Minimum Voltage Among inverting input Fig. 6 Timing chart for current-mode basic operation Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 16 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 At start-up, soft start can be realized through gradually increasing the threshold voltage based on CS pin voltage. At steady operation, the threshold voltage is varied based on FB pin voltage to keep power supply output voltage constant. In addition, the maximum IS pin threshold voltage as 520mV limits MOSFET over-current when FB pin voltage is very high like 4V by overload etc. The oscillator generates a pulse to determine the maximum duty cycle of an OUT pulse and the maximum duty cycle is set at 80% (typ.) using this pulse.. 3 60k 3R VCC FB 2 Buf x1 11µA IS comp. 5V Cs 1 CS 20k R 0.52V For details, refer to “9-(14) Timing chart”. Fig.7 IS Rs Current comparator (4) Blanking When MOSFET turns on, a surge current is generated due to discharge current from the capacitor in the main circuit or gate drive current. If the surge current reaches the IS pin threshold voltage, current comparator output could be inverted and normal pulses would not be generated from the OUT pin. To avoid this, a blanking function is incorporated into the current comparator. When a trigger signal is input from the oscillator, the blanking circuit outputs a certain-width pulse signal as a PWM latch (F.F.) set signal. Since the set signal is given a high priority in PWM latch input signals, the output of PWM latch (F.F.) will not be inverted while the set signal is input from the blanking circuit, even if a rest signal is input from the current comparator (IS comp.). As a result, the IS pin input voltage is ignored for a blanking time (200ns for FA5526/36, 400ns for FA5527/37 and 600ns for FA5528/38) immediately after an output pulse has been generated from the OUT pin and does not respond to a surge current at turn-on. （See Fig.8.） Fig.8 In general, the blanking circuit eliminates the need for a noise filter at the IS pin. Blanking Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 17 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 (5) Minimum ON pulse width As described in “(4) Blanking,” the input voltage at the IS pin is ignored during a blanking period right after turn-on. Consequently, the sum of blanking time and output delay time (100ns) is the minimum ON pulse width at the OUT pin of the IC. The minimum ON pulse width for FA5526/36, FA5527/37 and FA5528/38 are 300ns, 500ns and 700ns, respectively. In addition, a dedicated comparator is incorporated not to generate pulses at no load. When FB pin voltage is below 0.28V or CS pin voltage is below 0.68V, the output of the comparator is inverted and a clear signal “CLR” is input to the blanking circuit. Then, the blanking circuit will not output a set signal and no set signals will be input to PMW latch (F.F.), keeping the output voltage low. (See “9-(14) Timing chart.”) (6) Slope compensation In the current mode control, subharmonic oscillation may occur at a continuous current mode operation with a duty cycle of 50% or more. To avoid this, FA5526/36, FA5527/37 and FA5528/38 have built-in slope compensation circuits. For details of subharmonic oscillation phenomenon and slope compensation effect, see p.32. As shown in Fig.9, slope compensation is achieved by a input of FB pin voltage to the current comparator (IS comp.), which subtracted ramp signal generated from oscillator passing through slope generator. 5V Reg. 7.4k FB 2 1Meg 5pF SLOPE GENERATOR VCO OSC Q ( CS pin voltage ) / 4 60k 20k Ramp Signal +Σ 3 IS IS comp. 0.52V Rs Fig.9 Therefore, the threshold voltage at the FB pin gradually decreases with time within each switching cycle as shown in Fig.10 even when voltages at the FB pin and CS pin are constant. (See “9-(14) Timing chart.”) Slope compensation circuit Fig.10 Slope compensation Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 18 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 (7) Soft start circuit The CS pin is connected to a built-in constant current source. The current for soft start is 11uA. The capacitor externally connected to the CS pin is charged by the constant current source, gradually increasing CS pin voltage. MOSFET current gradually increases at start-up because CS pin voltage is input to the current comparator (IS comp.), realizing soft start. As a guide for soft start time, the time tss taken until CS pin voltage increases from 0V to 3V is given by the following equation. tss [ s ] = 0.27 * Cs [ uF ] ( typical value ) Here, Cs is a capacitance connected to CS pin [ uF ]. In steady operation, CS pin voltage is clamped at approximately 4V by a zener diode in the IC. The CS pin is provided with a built-in circuit to stop pulses when CS pin voltage is 0.68V or less, same as FB pin. (See “9-(14) Timing chart.”) Fig.11 Soft start circuit 3 IS 20k R 0.52V VCC FB 2 Buf x1 11µA 60k 3R IS comp. 1 5V Cs CS Cs (8) Overload protection of FA5526/27/28 FA5526, FA5527 and FA5528 have built-in time-latch type overload protection. Fig.12 shows its block diagram and Fig.13 its Timing chart. In steady operation, FB pin voltage is 3V or less and CS pin voltage is clamped at 4V by a zener diode in the IC. When power supply voltage drops on account of overload or short-circuit on the load side, FB pin voltage increases. If FB pin voltage exceeds the 3.6V threshold voltage for overload protection, output voltage of a comparator for overload detection (Overload) is inverted and 4V clamp of the CS pin is canceled, increasing CS pin voltage again due to a built-in constant current source. The current supplied from the CS pin becomes 4µA. If the power supply voltage continues to decrease and CS pin voltage reaches the threshold voltage (8.5V) of the comparator (Latch), the output of the comparator (Latch) is inverted, turning off a 5V circuit in the IC and forcing OUT pin voltage to be low. This status is the latch mode of the IC. In the latch mode, the start-up circuit resumes operation to supply current to Vcc and to hold the latch mode. Fig.12 FB 2 Overload SQ R F.F. 5V Reg. VCC 5V ENB 5V Reg. UVLO Latch 1 CS 6 VCC 11uA/4uA 8.5V/7.7V UVLO 2.8V 4.8V ENB 5 OUT Overload protection circuit Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 19 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 When the output voltage momentarily drops due to abrupt load change and FB pin voltage restores to the voltage at steady state before CS pin voltage reaches 8.5V, the 4V clamp circuit restarts, producing no latch mode. The latch mode can be reset through cutting off input voltage or through forcibly decreasing CS pin voltage to 7.4V or less. Cutting off the input voltage decreases VH pin voltage, supplying no current to the VCC pin. Thereafter, the latch mode is reset when Vcc drops below the OFF threshold voltage, 8.0Vmin. In addition, when CS pin voltage is forcibly decreased, the latch mode comparator is re-inverted and the IC re-starts switching operation. In the case of typical IC, delay time td (OLP), the time from overload detection to the latch mode, is given by the following equation. td1 (OLP) [ s ] = 0.93 * Cs [ uF ] ( typical value ) Fig.13 Short time Overload Overload Latch Off OUT pin Voltage CS pin Voltage 8.8V 8.5V FB pin Voltage 3.6V Secondary Side DC Output Voltage Here, Cs is a capacitance connected to CS pin [ uF ]. Delay time td(OLP) is inversely proportional to CS charging current and proportional to the difference between CS pin clamp voltage “4V” at steady condition and latch-mode threshold voltage “8.5V”. Pay attention to variations in delay time resulting from variations in numerical values. In addition, be aware that when the VH pin is connected after rectification, it takes rather long time, approximately several minutes, before the latch mode is reset. (See “9-(1) Start-up circuit.”) Vds Vcc Overload protection timing chart (20V /div) (100V /div) (9) Overload protection of FA5536/37/38 FA5536, FA5537 and FA5538 have built-in auto-recovery type overload protection. Fig.14 shows VCC pin voltage and the drain voltage of power MOSFET “Q1” in the circuit on page 33 at “6A” overload when 90Vac input is applied and Fig.15 shows same parameters mentioned above at “7A” overload when 264Vac input is applied. Switching period after the overload occurs and stop period are calculated as follows. Steady State to Overload : td2 (OLP) [ s ] = td1 (OLP), After overload starts : td2 (OLP) [ s ] = 1.65* Cs [ uF ], stop period t (stop) [ s ] = Cvcc [ uF ] * [ Vcc(sw/OL) – Vccoff ] / ( ICCL ) Here, Vcc(sw/OL) : Vcc in switching period at overload [ V ] Vccoff : OFF threshold voltage of U.V.L.O ( 9V (typ.)) ICCL : Consumption current in latch mode ( 290uA (typ.)) Fig.15 Overload protection waveform of FA5538 as Auto-Recovery ( 264Vac ) Vds (100V /div) Vcc (20V /div) Fig.14 Overload protection waveform of FA5538 as Auto-Recovery ( 90Vac ) Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 20 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 (10) Over-Voltage Protection of FA5526/27/28 FA5526, FA5527 and FA5528 have built-in over-voltage protection circuits to monitor Vcc voltage. Fig.16 shows its block diagram and Fig.17 its timing chart. When VCC voltage increases and exceeds comparator (OVP) reference voltage, 28V, an internal 1.3mA constant current source is tuned on. Since sink capability of the zener diode which clamps the CS pin at 4V is 55uA, CS pin voltage quickly increases when the 1mA constant current source is turned on. When CS voltage exceeds comparator (Latch) reference voltage, 8.5V, the IC changes to the latch mode. The delay time td (OVP), FB 2 Overload SQ R F.F. 5V Reg. VCC 5V ENB 5V Reg. UVLO Latch 1.3mA 8.5V/7.7V 28V UVLO 2.8V 4.8V ENB 5 OUT OVP Cs 1 CS 6 VCC the time from over-voltage detection to the latch mode, is given as follows. td (OVP) [ ms ] = 2.85 * Cs [ uF ] ( typical value ) Fig.16 Over Voltage protection circuit ( only for FA5526 / 5527 / 5528 ) Here, Cs is a capacitance connected to CS pin [ uF ]. In the latch mode, an internal power supply source, 5V “Reg” circuit, is turned off and OUT pin voltage is held to be low., and the current form the CS pin changes to 5µA. The latch mode can be reset through decreasing Vcc voltage due to cutting off of input voltage or through forcibly decreasing CS pin voltage to 7.4V or less. Moreover, pay attention to the relationship between wiring at the VH pin and reset time in the latch mode. （See “9-(1) Start-up circuit.”） (11) Over-Voltage Protection of FA5536/37/38 FA5536, FA5537 and FA5538 have built-in over-voltage protection ( OVP ) circuits to monitor Vcc voltage similar to FA5526/27/28. However, the OVP of FA5536/37/38 is Auto-Recovery mode. Therefore, when you need the OVP as latch mode, the additional external circuit is necessary as mentioned on page 28 to 29 ( See “10-(4)” ). Fig.17 Over-Voltage protection timing chart ( only for FA5526 / 5527 / 5528 ) (12) Under-Voltage Lock-Out circuit The IC has a built-in undervoltage lockout circuit to prevent malfunction when Vcc voltage drops. When Vcc voltage increases from 0V, the IC starts operation at Vcc = 15V (typ.). As the supply voltage decreases, the IC stops operation at Vcc = 9V(typ.). When the undervoltage lockout circuits operates and the IC stops operation, OUT pin and CS pin voltage are forced to be low, resetting soft start, and overload and overvoltage timer latch protection. Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 21 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 (13) Output circuit The output circuit consists of push-pull configuration, capable of directly driving a MOSFET. The maximum peak currents at the OUT pin are 0.25A for source current and 0.5A for sink current. If the IC stops operation when the under-voltage lockout circuit operates or in the latch mode, OUT pin voltage is forced to be low to shut down the MOSFET. (14) Timing chart Oscillator (OSC) Trigger (T) Output Blanking CLR Signal Blanking Output signal (set pulse) FB pin Voltage IS pin Voltage IS comp. output (reset pulse) FF “Q” output OSC Q output OUT pin Output voltage Blanking Time Fig.18 Timing chart at steady operation Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 22 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 Oscillator (OSC) Trigger (T) Output Oscillator (OSC) Trigger (T) Output Blanking CLR Signal Blanking CLR Signal Blanking Output signal (set pulse) Blanking Output signal (set pulse) FB pin Voltage FB pin Voltage 0.36V IS pin Voltage IS pin Voltage IS comp. output (reset pulse) IS comp. output (reset pulse) FF “Q” output FF “Q” output OSC Q output OSC Q output OUT pin Output voltage OUT pin Output voltage Fig.19 Timing chart at maximum duty cycle operation Fig.20 Timing chart at FB pin < 0.36V Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 23 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 Oscillator (OSC) Trigger (T) Output Blanking CLR Signal Blanking Output signal (set pulse) FB pin Voltage CS pin Voltage ( CS pin Voltage ) / 4 IS pin Voltage IS comp. output (reset pulse) FF “Q” output OSC Q output OUT pin Output voltage Blanking Time Minimum ON width ( The sum of Blanking Time and Delay Time to OUT pin ) ( CS pin voltage ) / 4 determines ON width as high voltage period of OUT pin Fig.21 Timing chart at start-up (soft start) Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 24 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 10．Design advice (1) Start-up and stop To properly start up and stop the power supply, optimum values shall be set for capacitors connected to the CS pin and VCC pin. Secondary Side DC Output Voltage (1-1) At start-up (1) It takes certain time until the output voltage reaches to the set voltage after the IC has been activated. During this period, FB pin voltage reaches its maximum voltage and the 4V clamp circuit does not operate. As a result, with proper CS pin capacitance and proper start-up, CS pin voltage waveform during start-up will be as shown in Fig.22. On the other hand, when CS pin capacitance is too small, CS pin voltage may reach the threshold voltage of the latch mode as shown in Fig.23 before the output voltage increases to the set value. The IC changes into a latch mode and the power supply cannot start properly. In cases like this, increase CS pin capacitance. (1-2) At start-up (2) Fig.24 shows Vcc voltage at start-up when proper capacitance is connected. When input power is turned on, the VCC capacitor is charged by the current supplied from the start-up circuit and its voltage increases. Then, when Vcc reaches the ON threshold voltage, the IC starts operation. In steady operation, the IC operates at the voltage supplied from an auxiliary winding. Right after IC start-up, however, Vcc drops until the auxiliary voltage increases sufficiently. Determine the capacitance connected to VCC pin so that Vcc does not drop to the OFF threshold voltage in any condition. We recommend that you choose the capacitance connected to VCC pin so that the bottom of Vcc becomes larger than 11V as the result of typical experiment. FB pin Voltage CS pin Voltage Start-up of IC 8.5V 4V 3V Start-up of IC b) Before CS pin exceeds 4V, FB pin voltage drops. a) After CS pin exceeds 4V, FB pin voltage drops. Fig.22 CS pin voltage waveform at start-up (1) ( normal start ) Secondary Side DC Output Voltage DC output set voltage FB pin Voltage CS pin Voltage Start-up of IC Fig.23 8.5V Latch Mode CS pin voltage waveform at start-up (2) （when the power supply can not start up） Fig.24 Vcc waveform at start-up (1) （at normal start-up） Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 25 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 When Vcc capacitance is too small, Vcc drops to the OFF threshold voltage as shown in Fig.25 before the auxiliary winding voltage increases sufficiently. In this case, Vcc repeatedly goes up and down between the ON and OFF threshold voltages, and the power supply can not start up. (1-3) At stopping When the power supply is turned off by shutdown of input voltage, output voltage remains low for certain period of time before the IC stops operation. During this period, FB pin voltage increases and the CS pin clamp circuit is cancelled because output voltage remains low. As a result, CS pin voltage increases as shown in Fig.26. CS pin voltage shall not reach the threshold voltage of the latch mode. As shown in Fig.27, if CS pin voltage reaches the threshold voltage, the latch mode is held for a period of time until Vcc capacitor voltage drops to OFF threshold voltage. As a result, the power supply cannot be re-started even if input voltage is turned on again. In such a case, the following measures shall be taken: ・Reduce the time taken until the IC stops operation after the output voltage has dropped through reducing Vcc capacitance. ・Suppress CS pin voltage rise through increasing CS pin capacitance. CS pin Voltage 8.5V FB pin Voltage VCC pin Voltage Secondary Side DC Output Voltage OFF Threshold Voltage ( 9V ) Fig.25 Vcc waveform at start-up (2) （when the power supply can not start up） (2) Hold time of Vcc In some cases, VCC pin capacitance shall be increased to hold Vcc above the OFF threshold voltage at abrupt load change after the power supply has started up. However, when VCC pin capacitance becomes larger, start-up time gets longer. In such a case, the circuit shown in Fig.28 is effective. Reducing C2 shortens start-up time, and hold time can be kept long because power is supplied via C4 after start-up. FB pin Voltage VCC pin Voltage Secondary Side DC Output Voltage Fig.26 Waveform at stopping (1) OFF Threshold Voltage ( 9V ) CS pin Voltage 8.5V Fig.28 Vcc circuit Fig.27 Latch Mode ( The period when IC can not re-start ) Waveform at stopping (2) Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 26 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 (3) Protection using CS pin for FA5526/27/28 In steady operation, the CS pin voltage is clamped by a 4V zener diode. Externally forcing CS pin voltage to increase to the threshold voltage, 8.5V, for the latch mode allows the IC to stop its operation for protection. In this case, a current of more than the sink capacity of 4V zener diode, 84uA, shall be applied to the CS pin. Set the input current to the CS pin at 1mA or less as a guide. The following shows examples of overvoltage protection at an arbitrary voltage using the CS pin. (3-1) Overvoltage detection on the secondary side Fig.29 shows an example of an overload detection circuit on the secondary side to change the IC into the latch mode. (3-2) Detection of Vcc (1) Fig.30 shows a circuit where the IC is stopped in the latch mode upon detecting Vcc overvoltage. In this case, Vcc voltage is latched at approximately ZD+8.5V. Use a ZD whose voltage is larger than the ON threshold voltage of the low-voltage malfunction preventive circuit. Otherwise, the IC cannot start. (3-3) Detection of Vcc (2) Fig.31 shows another circuit to detect Vcc overvoltage. In this case, Vcc voltage is latched approximately at ZD voltage. Use a ZD whose voltage is larger than the ON threshold voltage of the low-voltage malfunction preventive circuit. Otherwise, the IC cannot start. Fig.30 Over Voltage protection (2) for FA5526/27/28 Fig.29 Over Voltage protection (1) for FA5526/27/28 (4) Protection using CS pin for FA5536/37/38 FA5536/37/38 does not include any latch function. Therefore, the external latch circuit is necessary for Over-Voltage Protection as latch mode. Fig.32 shows the OVP latch circuit by primary side detection at VCC pin and Fig.33 shows the OVP latch circuit by secondary side detection through a optocoupler “PC”. When CS pin voltage is pulled down below 0.68V ( typ. ), the switching is shut-down. Once the NPN transistor “Q2” and “Q3” turn-on when the diode “ZD1” or optocoupler “PC” supplies the current to resistor “R1” by detection of Over-Voltage, PNP transistor “Q1” turns-on and “Q2” and “Q3” are maintained in ON-State. Then, CS pin voltage is maintained at low level until the current of a diode ZD2 is cut VCC pin voltage decreases below OFF threshold ( 9V ) . Fig.31 Over Voltage protection (3) for FA5526/27/28 Fig.32 Over Voltage protection (1) for FA5536/37/38 Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 27 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 (5) When not using an overload protection function As shown in Fig.34, connect a resistor R3 of 18k ohm between FB pin and GND. As a result, FB pin voltage does not increase to the threshold voltage for overload protection and the IC does not change to the latch mode even at overload. In this case, the latch protection for over-voltage is also available. (6) Correction of overload detection current ( Line Conversation ) If the power supply output becomes overload, the current of the MOSFET is limited by the maximum threshold voltage of the IS pin and power supply voltage drops. If the state continues as it is, an overload protection function operates to stop the IC in the latch mode. For details of an overload protection function, see “9-(8) Overload protection function.” When the overload protection operates, the output current of the power supply varies depending on the input voltage; and the higher the input voltage is, the larger the output current. In such a case, connect R4 between the current detection resistor Rs and IS pin, and add a correction resistor R5 as shown in Fig.35. The typical resistance of R5 is several hundreds of k ohm to several Meg ohm. Note that the above correction slightly decreases the value of overload current limit to stop the IC in the latch mode even if input voltage is low. Fig.34 When not using overload protection Fig.33 Over Voltage protection (2) for FA5536/37/38 Fig.35 Correction of overload detection current ( Line Conversation ) Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 28 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 (7) Improvement of input power at light load This IC is provided with a function to lower switching frequency at light load in order to reduce power dissipation. However, depending on the circuit used, switching frequency cannot be sufficiently reduced, leading to insufficient reduction of power dissipation at light load. In such a case, connect R6 between the auxiliary winding and the IS pin as shown in Fig.36. When R4 is 1k ohm, R6 is several hundreds of k ohm to 1Meg ohm. The smaller the R6 is, the lower the switching frequency at light load. However, negative voltage is applied to the IS pin due to R6 for some time while MOSFET is ON. Be aware that the negative voltage shall not be lower than absolute maximum rationg,-0.3V. In addition, when switching frequency is set too low at light load, transformer or other apparatus may produce noise. Fig.36 Input power improvement circuit at light load (8) Prevention of malfunction caused by noise This IC is an analog IC, and noise applied to anyone of the pins may cause malfunction. If malfunction is detected, use the IC through referring to the following description and fully checking a power supply unit. In addition, arrange the capacitors connected to pins as close to the IC as possible and take great care of wiring, for effective noise suppression. (8-1) FB pin The FB pin sets the threshold voltage of the current comparator. Any noise applied to the FB pin may disturb output pulses. Usually the capacitor C5 is connected as shown in Fig.37 to suppress noise. (8-2) IS pin As described in “9.-(4) Blanking,” this IC has a blanking function, and malfunction caused by a surge current produced at turn-on of the MOSFET is hard to occur. A malfunction, however, may occur when a surge current is excessively large or when any noise is externally applied at other than turn-off. In such a case, add a CR filter to the IS pin as shown in Fig.38. Fig.38 (8-3) VCC pin Relatively large noise may occur at the VCC pin because a large current flows from the VCC pin at the instant of driving the MOSFET. If noise is excessively large, a malfunction may occur of the IC. Pay full attention to capacitance and characteristics of the capacitor between the VCC pin and GND to reduce noise as much as possible. Prevention of malfunction caused by noise (IS pin) Fig.37 Prevention of malfunction caused by noise (FB pin) Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 29 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 (9) Over Temperature Protection as latch mode for FA5526 / 27 / 28 Over Temperature Protection as latch mode can be achieved by the circuit shown in Fig.39 for FA5526/27/28. Here, a diode D1 connected to separated line from VCC pin, because the start-up time of IC may become too long when the circuit including a thermistor is connected to VCC pin of IC directly. Please note that the circuit shown in Fig. 39 can not be used for FA5536/37/38, because FA5536/37/38 does not include any latch function. (10) Prevention of malfunction caused by negative voltage applied to pins When a large negative voltage is applied to a pin, a parasitic element in the IC may operate and cause a malfunction. Be sure that voltage applied to a pin shall not be -0.3V or less. Voltage oscillation generated at turn-off of the MOSFET may be applied to the OUT pin via the parasitic capacitance of the MOSFET, resulting in the negative voltage applied to the OUT pin. In such a case, connect a Shottky diode between each pin and GND. Forward voltage of the Shottky diode can suppress negative voltage at each pin. Use a Shottky diode with low forward voltage. Fig.40 shows an example of a circuit with a Shottky diode connected to the OUT pin. Fig. 39 Over Temperature Protection by Latch Mode for FA5526 / 5527 /5528 Note : OTP Latch by FA5536 / 5537 / 5538 can not be achieved by above circuit. FA5536 / 5537 / 5538 may need very complicated circuit for OTP latch. Fig.40 Negative voltage prevention circuit (11) Gate circuit configuration A resistor is generally inserted between the gate terminal of the MOSFET and the OUT pin of the IC for adjustment of switching speed, suppression of voltage oscillation at the gate terminal and other purposes. Sometimes, the drive currents for turning-on and -off must independently determined. In such a case, connect the gate terminal of the MOSFET and OUT pin of the IC as shown in Fig.41 or Fig.42. In Fig.41, the driving current is limited by Rg1 + Rg2 at turn-on and by only Rg2 at turn-off In Fig.42 the driving current is limited by only RG1 at turn-on and by parallel-connected Rg1 and Rg2 at turn-off. Fig.41 Gate circuit (1) Fig.42 Gate circuit (2) Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 30 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 (12) Loss calculation IC loss shall be determined to use the IC within its rating. Since it is hard to directly measure IC loss, an example of calculating approximate IC loss is given below. Total IC loss, Pd, is obtained by the following equation: Pd = Vcc * ( Iccop1 + Qg * f ) + VVH * IHrun Where Vcc is the supply voltage to the IC, Iccop1 is consumption current of the IC, Qg is total gate charge of the MOSFET, f is switching frequency, VVH is VH pin voltage and IHrun is a current flowing into the VH pin when the IC operates. This equation gives an approximate value of Pd, which is a little greater than the actual loss. Take into consideration variation and temperature characteristics of each value (Example) When the VH pin is connected to half-wave rectification waveform at power supply of 264Vac, the average VH pin voltage is approximately 119V. Under above condition, let us suppose Vcc = 18V and Qg = 80nC at Tj = 25 degree. When using FA5528 or FA5538, according to the specifications IHrun = 25uA = 0.025mA ( typ. ), Iccop1 = 1.4mA ( typ. ) and f = 60kHz = 0.06MHz ( typ.). Thus, typical IC loss Pd: Pd = 18V * ( 1.4mA + 80nC * 0.06MHz ) + 119V * 0.025mA = 115mW ( typ. ) Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 31 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 (Reference) Sub-harmonic oscillation and slope compensation In a peak-value-control current mode, when the converter operates in an inductor-current continuous mode and at duty cycle of 50% or more, the current may oscillate at an integral multiple of switching frequency. This oscillation is called subharmonic oscillation. Fig. 43 shows an example of inductor current waveform when a subharmonic oscillation occurs. It is found that ON and OFF periods vary while the peak value of an inductor current, switching cycle and current slopes during ON and OFF periods remain unchanged. The harmonic oscillation may increase ripple voltage contained in the output voltage or cause an unusual noise. The subharmonic oscillation can be prevented by giving a certain gradient to the threshold of the peak current as shown in Fig. 44. This is called slope compensation. Fig.44 Inductor current with slope compensation Fig.43 Inductor current without slope compensation Generally, the gradient of slope compensation required for preventing a subharmonic oscillation is given by the following relational expression: Ld  Lu 2 Kc  Here, Lu：Gradient of an inductor current during the ON period Ld：Gradient of an inductor current during the OFF period Kc：Gradient of slope compensation The above parameters are shown in Fig.45. Fig.45 Inductor current without slope compensation Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 32 http://www.fujielectric.co.jp/products/semiconductor/ FA5526/5527/5528/5536/5537/5538 11. Example of an application circuit The following circuit is common to both of FA5528 and FA5538. FA5526/27/28/36/37/38 can be used for same topology except the protection circuit and the transformer design which depends on switching frequency. Note : The example of an application circuit is intended to be used only for reference and not to guarantee performance or characteristics. Input power at no-load 250 200 150 100 50 0 50 100 150 200 Line Voltage (Vac) 250 300 Efficiency (Io=5A) 90 89 88 87 86 85 84 83 82 81 50 100 150 200 250 300 Line voltage (Vac) Over Current Protection vs. AC Line Voltage 7.0 6.5 6.0 5.5 5.0 4.5 4.0 I nput power (mW) Switching frequency at no-load 25 20 fs w (k Hz ) 15 10 5 0 50 100 150 200 Line voltage (Vac) 250 300 DC Output Current at OCP E ff ic ienc y (%) 80 100 120 140 160 180 200 220 240 260 280 AC Line Voltage ( V) Fuji Electric Co., Ltd. AN-087E Rev.1.0 April-2011 33 http://www.fujielectric.co.jp/products/semiconductor/