A-48W-K

MINIATURE RELAY 2 POLES—1 to 2 A (FOR SIGNAL SWITCHING) A SERIES n FEATURES RoHS compliant l Extremely low profile and light weight —Height: 5 mm —Weight: approximately 1.2 g l Meet FCC (Part 68) standard l Conforms to FCC rules and regulations part 68 —Surge strength 1,500 V l High reliability—bifurcated contacts l Wide operating range l DIL pitch terminals l Plastic sealed type l Latching version available l RoHS compliant since date code: 0437B8 Please see page 7 for more information n ORDERING INFORMATION [Example] (a) (b) (c) (d) (e) (f ) (g) A L – D 12 W – K - HA (a) (b) (*) (c) (d) (e) (f ) (g) A : A Series Nil : Standard type L : Latching type Nil : Single winding type D : Double winding type Refer to the COIL DATA CHART W : Bifurcated type K : Plastic sealed type Series Name Operation Function Number of Coil Nominal Voltage Contact Enclosure Coil Sensitivity Nil : Standard HA : 75% must voltage operate Note: ctual marking omits the hyphen (-) of (*) A 1 A SERIES n COIL DATA CHART MODEL A-1.5W-K A- 3 W-K Standard Type A-4.5W-K A- 5 W-K A- 6 W-K A- 9 W-K A-12 W-K A-18 W-K A-24 W-K A-48 W-K Nominal voltage 1.5 VDC 3 VDC 4.5 VDC 5 VDC 6 VDC 9 VDC 12 VDC 18 VDC 24 VDC 48 VDC Coil resistance (±10%) 16.1Ω 64.3Ω 145Ω 178Ω 257Ω 579Ω 1,028Ω 1,620Ω 2,880Ω 7,680Ω Must operate voltage*1 +1.13 VDC +2.25 VDC +3.38 VDC +3.75 VDC +4.5 VDC +6.75 VDC +9.0 VDC +13.5 VDC +18.0 VDC +36.0 VDC Must release voltage*1 +0.15 VDC +0.3 VDC +0.45 VDC +0.5 VDC +0.6 VDC +0.9 VDC +1.2 VDC +1.8 VDC +2.4 VDC +4.8 VDC Nominal power 140 mW 140 mW 140 mW 140 mW 140 mW 140 mW 140 mW 200 mW 200 mW 300 mW Note: *1 Specified values are subject to pulse wave voltage. All values in the table are measured at 20°C. MODEL AL-1.5W-K Single Winding Latching Type AL- 3 W-K AL-4.5W-K AL- 5 W-K AL- 6 W-K AL- 9 W-K AL-12 W-K AL-18 W-K AL-24 W-K AL-D1.5W-K AL-D 3 W-K AL-D4.5W-K Double Winding Latching Type AL-D 5 W-K AL-D 6 W-K AL-D 9 W-K AL-D12 W-K AL-D18 W-K AL-D24 W-K Nominal voltage 1.5 VDC 3 VDC 4.5 VDC 5 VDC 6 VDC 9 VDC 12 VDC 18 VDC 24 VDC 1.5 VDC 3 VDC 4.5 VDC 5 VDC 6 VDC 9 VDC 12 VDC 18 VDC 24 VDC Coil resistance (±10%) 22.5Ω 90Ω 203Ω 250Ω 360Ω 810Ω 1,440Ω 2,160Ω 3,840Ω P 11.25Ω S 11.25Ω P S P S P S P S P S P S 45Ω 45Ω 101Ω 101Ω 125Ω 125Ω 180Ω 180Ω 405Ω 405Ω 720Ω 720Ω +13.5 VDC +12.6 VDC +18.0 VDC +16.8 VDC P: Primary coil S: Secondary coil 300 mW +9.0 VDC +8.4 VDC 300 mW +6.75 VDC +6.3 VDC 200 mW +4.50 VDC +4.2 VDC 200 mW +3.75 VDC +3.5 VDC 200 mW +3.38 VDC +3.15 VDC 200 mW +2.25 VDC +2.1 VDC 200 mW Set voltage*1 +1.13 VDC +2.25 VDC +3.38 VDC +3.75 VDC +4.5 VDC +6.75 VDC +9.0 VDC +13.5 VDC +18.0 VDC +1.13 VDC +1.05 VDC Reset voltage*1 -1.05 VDC -2.1 VDC -3.15 VDC -3.5 VDC -4.2 VDC -6.3 VDC -8.4 VDC -12.6 VDC -16.8 VDC Nominal power 100 mW 100 mW 100 mW 100 mW 100 mW 100 mW 100 mW 150 mW 150 mW 200 mW 200 mW P 1,080Ω S 1,080Ω P 1,920Ω S 1,920Ω Note: *1 Specified values are subject to pulse wave voltage. All values in the table are measured at 20°C. 2 A SERIES n SPECIFICATIONS Contact Coil Time Value Life Other Item Arrangement Material Resistance (initial) Rating (resistive) Maximum Carrying Current Maximum Switching Power Maximum Switching Voltage Maximum Switching Current Minimum Switching Load*1 Capacitance Nominal Power (at 20°C) Operate Power (at 20°C) Operating Temperature Operate (at nominal voltage) Release (at nominal voltage) Mechanical Electrical Vibration Misoperation Resistance Endurance Shock Misoperation Resistance Endurance Weight Standard Type A-( ) W-K 2 form C (DPDT) Gold overlay silver alloy Maximum 50 mΩ (at 1 A 6 VDC) 0.5 A 125 VAC or 1 A 30 VDC 2 A 62.5 AV/30 W 125VAC, 110VDC 2 A 0.01 mA 10 mVDC Approximately 0.5 pF (between open contacts, adjacent contacts) Approximately 1.0 pF (between coil and contacts) 140 to 300 mW 100 to 150 mW 200 to 300 mW 80 to 170 W 60 to 85 mW Maximum 6 ms Maximum 6 ms (set) Maximum 4 ms Maximum 6 ms (reset) 1 × 108 ops. minimum 1 × 107 ops. minimum 2 × 105 ops. min. (0.5 A 125 VAC), 5 × 105 ops. min. (1 A 30 VDC) 10 to 55 Hz (double amplitude of 3.3 mm) 10 to 55 Hz (double amplitude of 5.0 mm) 500 m/s2 (11 ±1 ms) 1,000 m/s2 ( 6 ±1 ms) Approximately 1.2 g 150 to 170 mW –40°C to +85°C (no frost) (refer to the CHARACTERISTIC DATA) Single Winding Latching Type AL-( ) W-K Double Winding Latching Type AL-D ( ) W-K *1 Minimum switching loads mentioned above are reference values. Please perform the confirmation test with the actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. n INSULATION Item Resistance (initial) Dielectric Strength Surge Voltage Type UL Compliance open contacts coil and contacts adjacent contacts Minimum 1,000 MΩ (500VDC) 1,000 VAC 1 min. 1,000 VAC 1 min. 1500V (coil-contact) (10/160 µs standard wave) Contact rating Flammability: UL 94-V0 (plastics) 0.5A, 125VAC (General use) 2A, 30VDC (resistive) 0.3A, 110VDC (resistive) n SAFETY STANDARD AND FILE NUMBERS UL 478, UL 508 E 45026 CSA C22.2 No. 14 LR 35579 3 A SERIES n CHARACTERISTIC DATA 0.1 0.3 0.5 n REFERENCE DATA 4 A SERIES 5 A SERIES n DIMENSIONS l Dimensions l Schematics (Bottom View) l PC board mounting hole layout (Bottom View) A, AL type (Non-latching type, single winding latching type) AL-D type (Double winding latching type) Unit: mm 6 A SERIES RoHS Compliance and Lead Free Relay Information 1. General Information Relays produced after the specific date code that is indicated on each data sheet are lead-free now. Most of our signal and power relays are lead-free. Please refer to Lead-Free Status Info. (http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf) l Lead free solder paste currently used in relays is Sn-3.0Ag-0.5Cu. l All signal and most power relays also comply with RoHS. Please refer to individual data sheets. Relays that are RoHS compliant do not contain the 5 hazardous materials that are restricted by RoHS directive (lead, mercury, chromium IV, PBB, PBDE). l It has been verified that using lead-free relays in leaded assembly process will not cause any problems (compatible). l “LF” is marked on each outer and inner carton. (No marking on individual relays). l To avoid leaded relays (for lead-free sample, etc.) please consult with area sales office. l We will ship leaded relays as long as the leaded relay inventory exists. Note: Cadmium was exempted from RoHS on October 21, 2005. (Amendment to Directive 2002/95/EC) l 2. Recommended Lead Free Solder Profile l Recommended solder paste Sn-3.0Ag-0.5Cu. Reflow Solder condition Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C soler bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical realys. Dipped SnAgCu solder is known as low risk tin whisker. No considerable length whisker was found by our in house test. 4. Tin Whisker l 7 A SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://www.fujitsu.com/us/services/edevices/components/ Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ ©2008 Fujitsu Components America, Inc. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. Fujitsu Components America or its affiliates do not warrant that the content of datasheet is error free. In a continuing effort to improve our products Fujitsu Components America, Inc. or its affiliates reserve the right to change specifications/datasheets without prior notice. Rev. January 9, 2008. 8