FAR-F1DA-1M5440-G205

FUJITSU SEMICONDUCTOR DATA SHEET DS04-20100-3E ASSP TIMING EXTRACTION BANDPASS FILTER (1.5 to 100MHz) F1/F2/F3 SERIES s DESCRIPTION The F1, F2 and F3 Series were developed as timing extraction filters for primary, secondary, and tertiary digital communication devices. This new all-solid-state bandpass filter (BPF) uses a piezoelectric with a large electromechanical coefficient (lithium tantalate: LiTaO3). The filter has a wide bandwidth, and is very stable. s FEATURES • • • • Wide frequency range 1.5 to 100MHz Wide fractional bandwidth (%): 0.1 to 2.5 Low insertion loss: 6dB or less Excellent temperature characteristics: 1.5 to 35MHz: ±400ppm or less (0 to 60°C) 36 to 100MHz: –30ppm/°C (0 to 60°C) • Small frequency deviation ∆fO < ±500ppm eliminating the need for adjustment • Highly reliable hermetically sealed package • Compatible with small 14-pin DIP IC s PACKAGE 14-PIN DIP SIZE METAL CASE F1/F2/F3 SERIES s PIN ASSIGNMENT (BOTTOM VIEW) 1 7 14 8 Pin No. 1 7 8 14 Pin name IN GND NC OUT Input pin Ground pin No connection Output pin Description s MAXIMUM RATINGS Item Operating temperature Storage temperature Insulation resistance Frequency range Symbol Ta Tstg IR –– Rating –20 to 80 –40 to 80 100 (100V DC) 1.5 to 100 Unit °C °C MΩ MHz s RECOMMENDED OPERATING CONDITIONS Item Operating temperature Symbol Ta Rating 0 to 70 Unit °C 2 F1/F2/F3 SERIES s STANDARD FREQUENCY Series Standard frequency 1.544MHz 2.048MHz 3.088MHz 3.152MHz 4.096MHz F1 6.312MHz 8.192MHz 8.448MHz 12.624MHz 16.384MHz 16.896MHz F2 32.064MHz 34.368MHz F3 44.736MHz For the U.S. and Japan (secondary group) For the U.S. and Japan (secondary group) For Europe (secondary group) For the U.S. and Japan (secondary group) For the U.S. and Japan (secondary group) For Europe (secondary group) For Japan (tertiary group) For Europe (tertiary group) For the U.S. (tertiary group) 6.312 × 2 8.192 × 2 8.448 × 2 Application For the U.S. and Japan (primary group) For Europe (primary group) For the U.S. and Japan (primary group) For the U.S. and Japan (primary group) For Europe (primary group) 2.048 × 2 1.544 × 2 Remarks 3 F1/F2/F3 SERIES s ELECTRICAL CHARACTERISTICS F1 Series Item Frequency deviation Load Q Insertion loss Stop band attenuation Frequency stability with temperature Symbol ∆fO Q Condition –– –– –– fO ± 10MHz –– Rating Min. –500 1000 –– 20 –400 Typical –– –– –– –– –– Max. +500 40 6 –– +400 Unit ppm –– dB dB ppm Remarks fO standard IL AOUT ∆f (Ta) 25°C standard, Ta = 0 to 70°C F2 Series Item Frequency deviation Load Q Insertion loss Stop band attenuation Frequency stability with temperature Symbol ∆fO Q Condition –– –– –– fO ± 10MHz –– Rating Min. –500 1000 –– 20 –400 Typical –– –– –– –– –– Max. +500 40 6 –– +400 Unit ppm –– dB dB ppm Remarks fO standard IL AOUT ∆f (Ta) 25°C standard, Ta = 0 to 70°C F3 Series Item Frequency deviation Load Q Insertion loss Stop band attenuation Frequency stability with temperature Symbol ∆fO Q Condition –– –– –– fO ± 10MHz –– Rating Min. –500 200 –– 20 –1350 Typical –– –– –– –– –– Max. +500 50 6 –– 750 Unit ppm –– dB dB ppm Remarks fO standard IL AOUT ∆f (Ta) 25°C standard, Ta = 0 to 70°C 4 F1/F2/F3 SERIES s ELECTRICAL CHARACTERISTICS Specification No. Standard frequency (MHz) 1.544 1.544 1.544 1.544 2.048 2.048 3.088 3.152 4.096 6.312 6.312 8.192 8.448 12.624 16.384 16.896 32.064 34.368 44.736 Part number Load Q FAR-F1DA-1M5440-G201 FAR-F1DA-1M5440-G202 FAR-F1DA-1M5440-G203 FAR-F1DA-1M5440-G205 FAR-F1DA-2M0480-G201 FAR-F1DA-2M0480-G202 FAR-F1DA-3M0880-G201 FAR-F1DA-3M1520-G201 FAR-F1DA-4M0960-G201 FAR-F1DA-6M3120-G201 FAR-F1DA-6M3120-G202 FAR-F1DA-8M1920-G201 FAR-F1DA-8M4480-G201 FAR-F1DA-12M624-G201 FAR-F1DA-16M384-G201 FAR-F1DA-16M896-G201 FAR-F2DA-32M064-G201 FAR-F2DA-34M368-G201 FAR-F3DA-44M736-G201 110 ±20 110 ±20 60 ±10 110 ±20 40 ±10 100 ±20 150 ±20 85 ±15 110 ±20 110 ±20 110 ±20 100 ±20 110 ±20 100 ±20 100 ±20 100 ±20 100 ±10 100 ±10 65 ±15 Insertion loss, IL (dB) 3 or less 3 or less 3 or less 3 or less 3 or less 3 or less 3 or less 3 or less 3 or less 3 or less 3 or less 3 or less 3 or less 3 or less 3 or less 3 or less 3 or less 3 or less 6 or less Phase rotation θ (degree) –90±20 –90±20 –95±10 –90±20 –90±10 –90±20 –90±20 –90±15 –90±20 –90±20 –90±20 –90±20 –90±20 –90±20 –90±20 –90±20 –90±15 –90±15 38±10 Terminating impedance Z (Ω) 790 1000 2035/20pF 2000 2035 1000 640 1285 750 985 1000 980 980 590 410 390 100 100 105 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 s TEST CIRCUIT 50Ω Z Z 50Ω LM OSC 5 F1/F2/F3 SERIES s CHARACTERISTICS SAMPLE Pass band characteristic A : T/R (dB) B : A MAX 0.000 B MAX 180.0 θ 0 MKR dB GAIN deg PHASE 1544000.000Hz –722.721mdB –93.1330deg Stop band characteristic A : T/R (dB) B : A MAX 0.000 B MAX 180.0 θ 0 MKR dB GAIN deg PHASE 1544000.000Hz –724.276mdB deg A/DIV 1.000 B MIN –180.0 dB CENTER deg SPAN 1544000.000Hz 50000.000Hz A/DIV 5.000 B MIN –180.0 dB CENTER deg SPAN 1544000.000Hz 200000.000Hz Temperature characteristic F3 Series Frequency change (ppm) 1000 F2 Series F1 Series –1000 –20 0 20 40 60 Temperature (°C) 80 s PART NUMBERING SYSTEM [Example] FAR–F1DA– –G Œ Œ Series designation  Ž  Frequency designation: The standard frequency is designated in six alphanumeric characters. M is used to designate the decimal point in MHz. Refer to “ELECTRIC CHARACTERISTICS” in detail Example: 1.544MHz: 1M5440 Ž Serial number: 6 The serial number is assigned from 201 to 999 (201 is normal). F1/F2/F3 SERIES s MARKING Fujitu logo Standard frequency F G201×××××× F-1M5440 No. 1 pin position Lot number s DIMENSIONS Unit: mm (in.) 20.8 max (0.819) 18.3 (0.720) 5.5 (0.217) Hmax 10.7 (0.421) ø0.5 (0.020) 15.2 (0.598) 13.1 max (0.516) 1 7 7.6 (0.299) Series F1 < 3 MHz F1 ≥ 3 MHz F2 F3 H 8.5 (0.335) 5.8 (0.228) 5.8 (0.228) 5.8 (0.228) 14 8 7 FUJITSU LIMITED For further information please contact: Japan FUJITSU LIMITED Corporate Global Business Support Division Electronic Devices KAWASAKI PLANT, 4-1-1, Kamikodanaka Nakahara-ku, Kawasaki-shi Kanagawa 211-88, Japan Tel: (044) 754-3763 Fax: (044) 754-3329 North and South America FUJITSU MICROELECTRONICS, INC. Semiconductor Division 3545 North First Street San Jose, CA 95134-1804, U.S.A. Tel: (408) 922-9000 Fax: (408) 432-9044/9045 Europe FUJITSU MIKROELEKTRONIK GmbH Am Siebenstein 6-10 63303 Dreieich-Buchschlag Germany Tel: (06103) 690-0 Fax: (06103) 690-122 Asia Pacific FUJITSU MICROELECTRONICS ASIA PTE. LIMITED #05-08, 151 Lorong Chuan New Tech Park Singapore 556741 Tel: (65) 281-0770 Fax: (65) 281-0220 All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information and circuit diagrams in this document presented as examples of semiconductor device applications, and are not intended to be incorporated in devices for actual use. Also, FUJITSU is unable to assume responsibility for infringement of any patent rights or other rights of third parties arising from the use of this information or circuit diagrams. FUJITSU semiconductor devices are intended for use in standard applications (computers, office automation and other office equipment, industrial, communications, and measurement equipment, personal or household devices, etc.). CAUTION: Customers considering the use of our products in special applications where failure or abnormal operation may directly affect human lives or cause physical injury or property damage, or where extremely high levels of reliability are demanded (such as aerospace systems, atomic energy controls, sea floor repeaters, vehicle operating controls, medical devices for life support, etc.) are requested to consult with FUJITSU sales representatives before such use. The company will not be responsible for damages arising from such use without prior approval. Any semiconductor devices have inherently a certain rate of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Control Law of Japan, the prior authorization by Japanese government should be required for export of those products from Japan. F9703 © FUJITSU LIMITED Printed in Japan 24