FAR-M2CC

FUJITSU SEMICONDUCTOR DATA SHEET DS04-21710-1E ASSP Piezoelectric VCO (6 to 30 MHz) M2 Series (F150) s DESCRIPTION The M2 series (F150) of VCO (Voltage Controlled Oscillator) apply to the frequency range 6 to 30 MHz. These VCOs have a high stability and wide controllable frequency ranges using a LiTaO3 piezoelectric single crystal with high electromechanical coupling coefficient. Output level applies to CMOS type for digital interface. s FEATURES • • • • • • Wide frequency controllable range (Over than ±2000 ppm) High carrier noise ratio Excellent temperature stability CMOS output level Compact package (8 × 11 × 2.6 mm) Surface mountable package (SMD) s PACKAGE 1 M2 Series (F150) s PIN ASSIGNMENT (Bottom View) 3 4 2 1 s PIN DESCRIPTIONS Pin No. 1 2 3 4 Symbol VIN GND VCC VOUT GROUND VCC (Supply voltage) OUTPUT Descriptions INPUT (Control voltage) 2 M2 Series (F150) s ABSOLUTE MAXIMUM RATINGS Parameter Symbol VCC VIN VOUT IOUT Ta Tstg Rating Min. –0.5 –0.5 –0.5 –25 –10 –40 Max. +7.0 +7.0 VCC +0.5 +25 +70 +100 Unit V V V mA °C °C Supply voltage Control voltage Output voltage Output current Operating temperature Storage temperature WARNING: Piezoelectric devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings. s RECOMMENDED OPERATING CONDITIONS Parameter Symbol VCC VIN Ta Value Min. +4.75 0 –10 Max. +5.25 +5.0 +70 Unit V V °C Supply voltage Control voltage Operating temperature WARNING: The recommended operating conditions are required in order to ensure the normal operation of the piezoelectric device. All of the device’s electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their FUJITSU representatives beforehand. s STANDARD FREQUENCIES Nominal frequency 14.318 MHz 16.934 MHz 18.432 MHz 24.576 MHz 25.175 MHz Part number FAR-M2CC-14M318-F150 FAR-M2CC-16M934-F150 FAR-M2CC-18M432-F150 FAR-M2CC-24M576-F150 FAR-M2CC-25M175-F150 Application Video Audio Video Audio Display 3 M2 Series (F150) s ELECTRICAL CHARACTERISTICS Parameter Symbol ICC “H” “L” VOH VOL fH fL ∆f(VCC) ∆f(Ta) Condition Without load VIN = 2.5 V VIN = 5.0 V VIN = 0.0 V VCC = 4.75 V to 5.25 V VIN = 2.5 V VIN = 2.5 V Ta = –10 to +70 °C Value Min. — VCC – 0.5 — +2000 — –150 –500 Typ. 5.0 5.0 0 — — — — Max. 10 — +0.5 — –2000 +150 +500 Unit mA V V ppm Nominal frequency ppm reference VCC = 5.0 ppm reference V ppm 25°C reference Remarks Current consumption Output voltage Oscillation frequency Frequency stability Frequency stability with temperature Unless otherwise specified Ta = +25 °C, VCC = 5.0 V s MEASURMENT CIRCUIT VCC 0.1 µF 3 VIN 1 Output 4 CL = 22 pF 2 GND CL includes capacitance of probe and test fixture 4 M2 Series (F150) s TYPICAL CHARACTERISTICS Part number: FAR-M2CC-16M934-F150 1. Control Voltage vs. Oscillation Frequency Variation 6000 Oscillation frequency variation (ppm) 4000 2000 0 −2000 −4000 −6000 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Control voltage (V) 2. Temperature Characteristics 1000 Oscillation frequency variation (ppm) 800 600 400 200 0 −200 −400 −600 −800 −1000 −20 −10 0 10 20 30 40 50 60 70 80 Temperature (degree C) 3. Supply Voltage (Vcc) vs. Oscillation Frequency Variation 500 Oscillation frequency variation (ppm) 400 300 200 100 0 −100 −200 −300 −400 −500 4.5 4.75 5 Supply voltage (V) 5.25 5.5 5 M2 Series (F150) s PART NUMBER DESIGNATION [Designation example] FAR – M2CC – (1) – F150 – R (2) (1) : Frequency : This specifies the nominal frequency using six alphanumeric characters. M indicates the decimal point. [Example] 24.576 MHz → 24M576 (2) : Taping : “–R” means 1000 pcs/reel s MARKING Logo Frequency F 24M576 Lot Number Index 6 M2 Series (F150) s PACKAGE DIMENSION 9.90 +0.00 -0.20 7.60 ± 0.10 0.60 ± 0.10 2.60 ± 0.15 0.80 2.00 0.80 1.60 8.00 ± 0.20 5.10 11.00 ± 0.50 Dimensions in mm. 7 M2 Series (F150) s PACKAGE: Reel type 1.75 ± 0.1 4.0 ± 0.1 2.0 ± 0.1 φ1.5 -0.0 +0.1 0 . 3 ± 0 .0 5 11.5 ± 0.1 12.1 ± 0.1 24.0 ± 0.3 8.8 ± 0.1 12.0 ± 0.1 φ2.0 +0.1 -0.0 25.5 ± 1.5 φ13.0 ± 0.5 φ21.0 ± 0.8 φ330 ± 2.0 φ80 1.5 ± 0.2 Type Quantity R 1 k pcs 8 11.8 ± 0.1 3 .2 ± 0 .1 M2 Series (F150) FUJITSU LIMITED For further information please contact: Japan FUJITSU MEDIA DEVICES LIMITED Marketing and Technical Support Dept. SUN HAMADA BLDG 2F 1-19-20,Shin-yokohama Kouhoku-ku, Yokohama-shi Kanagawa 222-0033, Japan Tel: 81(45) 471-0067 Fax: 81(45) 471-0069 All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information and circuit diagrams in this document are presented as examples of semiconductor device applications, and are not intended to be incorporated in devices for actual use. Also, FUJITSU is unable to assume responsibility for infringement of any patent rights or other rights of third parties arising from the use of this information or circuit diagrams. FUJITSU semiconductor devices are intended for use in standard applications (computers, office automation and other office equipment, industrial, communications, and measurement equipment, personal or household devices, etc.). CAUTION: Customers considering the use of our products in special applications where failure or abnormal operation may directly affect human lives or cause physical injury or property damage, or where extremely high levels of reliability are demanded (such as aerospace systems, atomic energy controls, sea floor repeaters, vehicle operating controls, medical devices for life support, etc.) are requested to consult with FUJITSU sales representatives before such use. The company will not be responsible for damages arising from such use without prior approval. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be required for export of those products from Japan. http://www.fujitsu.co.jp/ North and South America FUJITSU MICROELECTRONICS, INC. Semiconductor Division 3545 North First Street San Jose, CA 95134-1804, USA Tel: (408) 922-9000 Fax: (408) 922-9179 Customer Response Center Mon. - Fri.: 7 am - 5 pm (PST) Tel: (800) 866-8608 Fax: (408) 922-9179 http://www.fujitsumicro.com/ Europe FUJITSU MIKROELEKTRONIK GmbH Am Siebenstein 6-10 D-63303 Dreieich-Buchschlag Germany Tel: (06103) 690-0 Fax: (06103) 690-122 http://www.fujitsu-ede.com/ Asia Pacific FUJITSU MICROELECTRONICS ASIA PTE LTD #05-08, 151 Lorong Chuan New Tech Park Singapore 556741 Tel: (65) 281-0770 Fax: (65) 281-0220 http://www.fmap.com.sg/ F9812 © FUJITSU LIMITED Printed in Japan 9