FBR582ND24-W

FTR-K1 SERIES COMPACT POWER RELAY 1 POLE x 2 - 12A (28VDC) (For 24V battery automotive applications) FBR572, 582 Series n FEATURES Two independent relays mounted in a single package l High current contact capacity (carrying current: 40 A/2 minutes, 30 A/1 hour) l Suitable for controlling 24 V motors in trucks and other large vehicles l High heat resistance and extended operating voltage l Two types of contact gap (FBR572: 0.8 mm, FBR582: 1.4 mm) l RoHS compliant Please see page 8 for more information l n PARTNUMBER INFORMATION [Example] FBR572 (a) N (b) D24 (c) - W1 (d) - ** (e) (a) Relay type FBR572 : FBR572 Series (contact gap 0.8mm) FBR582 : FBR582 Series (contact gap 1.4mm) (b) N Enclosure : Plastic sealed type (c) Coil rated voltage D24 : 24 VDC Coil rating table at page 2 (d) Contact material W1 Y : Silver-tin oxide indium : Silver-tin oxide (e) To be assigned custom specification Special type Actual marking does not carry the type name: "FBR" E.g.: Ordering code: FBR572ND24-W1 Actual marking: 572ND24-W1 1 FTR-K1 SERIES FBR572, 582 SERIES SPECIFICATION n Item Contact Data Life Coil Data Timing Data Other FBR572 FBR582 Configuration 1 form C x 2 (SPDT x 2) Material Silver-tin oxide indium (-W1 type) Silver-tin oxide (-Y type) Voltage drop Maximum 100 mV at 2A, 12VDC Contact rating 28VDC, 12A (locked motor load) 28VDC, Inrush 15A, break 2.5A (motor free load) Max. carrying current 40A/2 minutes, 30A/1 hour (25 °C, 100% rated coil voltage) Max. inrush current (reference) 60A Max. switching voltage (reference) 28VDC 32VDC Max. switching current (reference) 12A 14A Min. switching load (reference) * 6 VDC, 1A Mechanical Min. 10 x 106 operations Min. 1 x 106 operations Electrical Min. 100 x 103 operations (locked motor load) Min. 500 x 103 operations (motor free load) Min. 100 x 103 operations (locked motor load) Operating temperature range -40 °C to +85 °C (no frost) Storage temperature range -40 °C to +100 °C (no frost) Operate (at nominal voltage) Max. 10 ms Release (at nominal voltage) Max. 5 ms Vibration resistance 10 to 55Hz double amplitude 1.5mm Shock Misoperation 100m/s² Endurance 1,000m/s² Weight Approximately18 g * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. n COIL RATING Series FBR572 FBR582 Coil Code Rated Coil Voltage (VDC) D24 24 Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Thermal resistance (°C / W) 384 14.4 (at 20 °C) 67 170 18 (at 85 °C) 56 Note: All values in the table are valid for 20°C and zero contact current, unless otherwise stated. * Specified operate values are valid for pulse wave voltage. 2 FTR-K1 SERIES FBR572, 582 SERIES n n PRINCIPAL APPLICATIONS Application Normal load current Life x 103 Recommended model (Example) Power window 10A to 12A (switching at motor locking) 100 FBR582ND24-W1 Automatic door lock 5A/2 door (switching at motor locking) 100 FBR572ND24-W1 CHARACTERISTIC DATA 3 FTR-K1 SERIES FBR572, 582 SERIES Life test (example) (1) Motor lock Test item Test circuit Current wave form Test circuit Current wave form 12A, 28VDC Motor lock 100,000 operations minimun Contact material: Silver tin oxide indium (2) Motor free Test item Inrush 15A, Idle 2.5A 28VDC Motor free 500,000 operations minimum Contact material: Silver tin oxide indium 4 FTR-K1 SERIES FBR572, 582 SERIES 5 FTR-K1 SERIES FBR572, 582 SERIES n DIMENSIONS FBR572 l l Dimensions l Schematics (BOTTOM VIEW) l PC board mounting hole layout (BOTTOM VIEW) Tube carrier Unit: mm 6 FTR-K1 SERIES FBR572, 582 SERIES n DIMENSIONS FBR582 l l Dimensions l Schematics (BOTTOM VIEW) l PC board mounting hole layout (BOTTOM VIEW) Tube carrier Unit: mm 7 FTR-K1 SERIES FBR572, 582 SERIES RoHS Compliance and Lead Free Information 1. General Information All relays produced by Fujitsu Components are compliant with RoHS directive 2011/65/EU including amendments. l Cadmium as used in electrical contacts is exempted from the RoHS directives. As per Annex III of directive 2011/65/EU. l All relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/downloads/MICRO/fcai/relays/lead-free-letter.pdf l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. l 2. Recommended Lead Free Solder Condition l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: Duration: maximum 360˚C maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 8 FTR-K1 SERIES FBR572, 582 SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://us.fujitsu.com/components Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ ©2013 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. July 03, 2013 9