FTP-622DCL001

24V DRIVE INTERFACE BOARD (PARALLEL) FTP-622DCL001/011/ FTP-622DSL001/011/012 FOR FTP-622/632/642MCL001/002/301/302/303/304 s INTERFACE 1. Centronics (1) Connector (CN1) Connector part number : FCN-605Q030-G/S (Fujitsu Components) Mating connector part number : FCN-607B030-G/D (Fujitsu Components) or equivalent (2) Connector pin assignment No. 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 Signal PRSTB PRDT0 PRDT1 PRDT2 PRDT3 PRDT4 PRDT5 PRDT6 PRDT7 ACKNLG BUSY RINF2 SLCTIN RINF1 ATF I/O I I I I I I I I I O O O I O I Contents Data strobe Data 0 Data 1 Data 2 Data 3 Data 4 Data 5 Data 6 Data 7 Data input acknowledge Busy Printer status Printer select Printer status Paper feed request No. 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Signal PRSTB-RET PRDT0-RET PRDT1-RET PRDT2-RET PRDT3-RET PRDT4-RET PRDT5-RET PRDT6-RET PRDT7-RET ACKNLG-RET BUSY-RET INPRM-RET INPRM RINF3 GND I/O — — — — — — — — — — — — I O — Contents Connected to logic GND Connected to logic GND Connected to logic GND Connected to logic GND Connected to logic GND Connected to logic GND Connected to logic GND Connected to logic GND Connected to logic GND Connected to logic GND Connected to logic GND Connected to logic GND Reset Printer status Logic GND Notes: • Symbol “— means a negative logic signal. —” • “–RET” signal is a return signal of the twisted pair cable. • “I” or “O” means a signal direction from the interface board side. (3) Connector pin number (4) Data input signal timing PRDT0~7 t1 t3 FCN-605Q030-G/S (Fujitsu Components) or equivalent No.1 PRSTB t2 BUSY t4 ACKNLG No.30 No.2 Data set time :t1≥0.5 µsec PRSTB pulse :t2≥0.5 µsec Data hold time :t3≥0.5 µsec t5 PRSTB to BUSY= “H” :t4≤0.5 µsec . ACKNLG pulse :t5=5.0 µsec . 1 FTP-622DCL/DSL Product Parallel Interface Board Part Number FTP-622DCL001 FTP-622DCL011 FTP-622DSL001 FTP-622DSL011 Function Standard (without cutter) With cutter control Standard (without cutter) With cutter controller With cutter controller + FLASH ROM With Cutter + KANJI+FLASH ROM Serial Interface Board FTP-622DSL012 FTP-622DSL112 s SPECIFICATION Item Data receive speed Synchronous method Hand shake Input output level Signal level Specification 19200, 9600, 4800, 1200 bps (set by dip switch) Asynchronous, full duplex DTR/DSR signal or XON/XOFF RS232C Space (logic = 0) Mark (logic = 0) +3 V ~ +12 V –3 V ~ –12 V 2. SERIAL INTERFACE (RS232C) (1) Connector (CN2) Part number : B6B-XH-A (J.S.T) Mating connector part number : XHP-6 (J.S.T) or equivalent (2) Pin assignment No. 1 3 5 Signal FG TD GND I/O — O — Contents Frame GND Transmission Data Signal GND No. 2 4 6 Signal RD DTR DSR I/O I O I Receive data Data terminal ready Data set ready Contents Notes: “I” or “O” means a signal direction from the interface board side. (3) Pin number B6B-XH-A (J.S.T) CN2 CN1 6 1 2 FTP-622DCL/DSL s CONNECTOR PIN ASSIGNMENT 1. Connector for power supply (CN10) Part number : B6P-VH (J.S.T) Mating connector part number : VHR-6N (J.S.T) or equivalent No. 1 3 5 Signal VCC GND VDD I/O — — — Contents Power supply for logic (+5 V) GND (5 V, 24 V common) Power for head/motor (+24 V) No. 2 4 6 Signal GND GND V DD I/O — — — Contents GND (5 V, 24 V common) GND (5 V, 24 V common) Power for head/motor (+24 V) 2. Connector for thermal head drive (CN8) Part number : B16B-PH-K-S (J.S.T) Mating connector part number : PHR-16 (J.S.T) or equivalent No. 1 3 5 7 9 11 13 15 Signal VDH GND (VDH) STB1 STB3 STB4 STB5 HCLK GND (VDH) I/O O — O O O O O — Contents Power for head (+24 V) Head GND Print enable signal 1 Print enable signal 3 Print enable signal 4 Print enable signal 5 Data transmission clock Head GND No. 2 4 6 8 10 12 14 16 Signal VDH GND (VDH) STB2 TMP LAT 5 VH HD VDH I/O O — O I O O O O Contents Power for head (+24 V) Head GND Print enable signal 2 Temperature detection signal Print data latch signal Power for logic (+5 V) Print data output signal Power for head (+24 V) Notes: • Symbol “— means a negative logic signal. —” • “I” or “O” means a signal direction from the interface board side. 3. Connector for Sensor (CN3) Part number No. 1 3 5 Signal +5 V GND (5 V) HUP I/O — — I : B5B-PH-K-S (J.S.T) Contents Power for logic (+5 V) Logic GND Head-up detect signal No. 2 4 Signal PES +5 V I/O I — Contents Paper end detect signal Power for logic (+5 V) 3 FTP-622DCL/DSL 7. Connector for control signal input/ output (CN1) Part number Mating connector No. 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 NC NC NC NC NC NC NC NC NC NC NC NC SLCTIN NC ATF Signal I/O — — — — — — — — — — — — I — I : FCN-605Q030-G/S (Fujitsu Components) : FCN-607B030-G/D (Fujitsu Components) or equivalent Contents No connection No connection No connection No connection No connection No connection No connection No connection No connection No connection No connection No connection Select signal No connection Paper feed request No. 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 NC NC NC NC NC NC NC NC NC NC NC NC INPRM NC GND Signal I/O — — — — — — — — — — — — I — — Contents No connection No connection No connection No connection No connection No connection No connection No connection No connection No connection No connection No connection Reset signal No connection GND *Do not connect outside signal to NC. 4 FTP-622DCL/DSL 4. Connector for paper near end detection (CN5) Part number : B2B-PH-K-S (J.S.T) Mating connector part number : PHR-2 (J.S.T) or equivalent No. 1 Signal +5 V I/O — Contents Power for logic (+5 V) No. 2 Signal NES I/O I Contents Paper near end detect signal 5. Connector for stepping motor drive (CN13) Part number No. 1 3 Signal MT/B MT/A I/O O O : B4B-PH-K-S (J.S.T) Contents Stepping motor coil excitation Stepping motor coil excitation No. 2 4 Signal MT/B MT/A I/O O O Contents Stepping motor coil excitation Stepping motor coil excitation 6. Connector for cutter drive (CN11) *1 Part number No. 1 3 Signal SW1 M+ I/O I O : B4B-EH (J.S.T) Contents Cutter position detect signal Motor control signal (+) No. 2 4 Signal GND MI/O — O Logic ground Motor control signal (-) Contents *1: Only for FTP-622DCL011/111. 5 FTP-622DCL/DSL s PRINTING COMMANDS (CENTRONICS INTERFACE) Command HT LF FF ESC RS ESC US ESC ! +n ESC* +m+n1+n2+d1~dN ESC 2 ESC 3 + n ESC @ ESC A+n ESC C+n ESC D+d1~dN+NUL ESC J+n ESC K+n ESC c+1+n ESC R+n ESC s+n ESC d+n ESC e+n ESC t+n ESC {+n ECS EM+n ESC X+n+m ESC V+n ESC %+n ESC &+y+c1+c2+x+d1~dn ESC ?+n FS E+n FS ! +n FS & Contents Moves the print position to the next tab. Line feed. Feeds forms (new page). Sets reverse printing. Resets reverse printing. Sets print mode. Sets the bit image mode “m” for n1, n2 dot numbers. Sets 1/6 inch line feed length. Sets the line feed length. Printer initialization. Sets the space between lines. Sets the page length by character line. Sets the tab position. Feeds paper in forward direction. Feeds paper in reverse direction. Sets the internal processing. Selects the international character. Sets the printing speed. Printing and n-line feeding. Reverse line feed in “n” lines after printing. Character code table selection. Sets/resets the upside down printing. Automatic paper feed distance setting. Setting turning time of the motor excitation. Right Rotation 90° specification / cancellation. Selects the font to download*3. Registers the download front*3. External character registration deletion*3. Correction of impressed energy. Sets the Kanji print mode*1. Sets Kanji mode*1. (Continued) 6 FTP-622DCL/DSL (Continued) Command FS . FS C+n FS 9+n FS*+m+n1+n2+d1~dn FS r+n FS W+n GS < GS A+m+n GS E+n GS V+n+m GS e+n+m GS h+n GS k+m+n+d1~dN GS w+n GS &+m+x+y1+y2+[d]k GS '+m+n GS a+n Contents Resets Kanji mode*1. Selects Kanji code type*1. Sets the detection functions. Prints image data on SRAM*3. Notifies of printing finish*4. Sets/resets 4 times enlarged character. Line feeds to the next mark. Sets the line feed length after mark detection. Sets print quality. Executes paper cutting*2. Sets the bar width. Sets the barcode height. Selects the barcode type and prints. Sets the barcode length. Registration of image data*3. Prints registered image data *3. Sets and cancels status transmission (valid only for DSL)*3. *1: Only for FTP-622DSL112. *2: Only for FTP-622DCL011 or FTP-622DSL011/012. *3: Only for FTP-622DSL012. *4: Only for FTP-622DSL011/012. 7 FTP-622DCL/DSL s OPTIONS 1. Cable (With FTP-622MCL, FTP-632MCL, FTP-642MCL) Name Thermal head connection cable (CN8)* Centronics (CN1) Interface cable Serial (CN2) Power cable for head, motor, and logic (CN10) * short cable option FTP-622Y301 FTP-622Y401 FTP-624Y001 500 mm (19.71 inches) 300 mm (11.8 inches) 150 mm (5.9 inches) Part Number FTP-622Y001 FTP-622Y201 Cable Length 270 mm (10.6 inches) 500 mm (19.71 inches) 2. Paper holder Name Flange Stand Part number FTP-040HF FTP-040HS Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: marcom@fcai.fujitsu.com Web: www.fcai.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: www.fceu.fujitsu.com Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #04-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com www.fcal.fujitsu.com © 2004 Fujitsu Components America, Inc. All company and product names are trademarks or registered trademarks of their respective owners. Rev. 11/15/2004. 8