FTP-628MCL354-01

BATTERY DRIVEN, FTP-608 Series 2” HIGH SPEED THERMAL PRINTER FTP-628MCL353/354 #01 / #02 s OVERVIEW The FTP-628 MCL Series are battery driven high-speed printers with a 2-inch paper width equivalent. The FTP-628 MCL Series can be used for a variety of applications, such as portable terminals, POS, ticket issuing machines, label printers, banking terminals, and measurement and medical equipment. s HIGHLIGHTS • Ultra compact Height 26.4 mm, width 83.5 mm, depth 43.0 mm • High speed printing It can print at 60 mm/s (480 dotlines/s) maximum by using Fujitsu's unique head drive control. • Auto Cutter Full cut type (#01) and partial cut type (#02) printers are available. • Easy paper setting Our unique platen release mechanism allows a wide paper route even if the printer is ultra-compact, so paper can be easily inserted. Conventional auto loading is also available. FTP-628MCL354 FTP-628DSL306 1 FTP-628MCL353/354 s PART NUMBERS Part Number FTP-628MCL353#01 (front paper insertion, full cut type with knob) FTP-628MCL353#02 (front paper insertion, partial cut type with knob) FTP-628MCL354#01 (bottom paper insertion, full cut type without knob) FTP-628MCL354#02 (bottom paper insertion, partial cut type without knob) FTP-628CU301 (ANK only) FTP-628DCL301 Parallel (Centronics) FTP-628DSL306 Serial (RS232C) FTP-628Y202 Printer mechanism with Cutter LSI for driving Interface Board Cutter for Mech/Cutter supported Interface cables Parallel (Centronics) Serial (RS232C) FTP-628Y302 Power cable Head, motor, logic FTP-628Y402 s SPECIFICATIONS Item Part number Printing method Dot structure Dot pitch (Horizontal) Dot pitch (Vertical) Effective printing area Number of columns Paper width Paper thickness Printing Speed Character types Specifications FTP-628MCL353#01/#02, FTP-628MCL354#01/#02 Thermal-line dot method 384 dots/line 0.125 mm (8 dots/mm)—Dot density 0.125 mm (8 dots/mm)—Line feed pitch 48 mm ANK 32 columns/line (maximum 12 x 24 dot font) 58 mm 60 to 80 µ m (some paper in this range may not be used because of paper characteristics) Maximum 60mm/sec. (480 dot line/sec.) at 8.5V Alphanumeric, kana: International characters: JIS Kanji (Kanji CG loaded board): 12 × 24 dots, (1.5 × 3.0 mm), 32 columns: ANK 24 × 24 dots, (3.0 × 3.0 mm), 16 columns: ANK 8 × 16 dots, (1.0 × 2.0 mm), 48 columns: ANK 16 × 16 dots, (2.0 × 2.0 mm), 24 columns: ANK 159 types 195 types about 6800 types Character, dimensions (W×H), number of columns 2 FTP-628MCL353/354 s SPECIFICATIONS Item Interface For print head Power supply For motor For cutter For logic Mechanism with cutter Dimensions Interface board Mechanism with cutter Weight Interface board Head Life Cutter Operating temperature* Operating humidity Operating environment Storage temperature Storage humidity Head temperature detection Paper out/mark detection Platen release Approximately 20g Pulse resistance: 100 million pulses/dot (under our standard conditions); Abrasion resistance: paper traveling distance 50km (print ratio: 25% or less) 300,000 cuts 0˚ C to 50˚ C 20 to 85% RH (no condensation) -20˚ C to +60˚ C (paper not included) 5 to 95% RH (no condensation) Detected by thermistor Detected by photo-interrupter Detected by sliding switch High Sensitive Paper Standard paper: TF50KS-E4 (Nippon Paper) TF60KS-E(Nippon Paper), FTP020PU001 (58mm), PD105R (Oji Paper), FTP-020P0701 (58mm) TF60KS-F1, FTP-020P0102 (58mm), PD170R (Oji Paper), P220VBB-1 Mitsubishi Paper) PD160R-N (Oji Paper), AFB-235 (Mitsubishi Paper), TP50KJ-R (Nippon Paper), HA220AA (Nippon Paper) 69.3 x 52 x 15mm Approximately 120g Specification Conforms to RS232C / Centronics 4.2 - 8.5 VDC average current, 0.78A (0.93A) peak value (print ratio: 12.5%, print speed: 50mm/sec. at 7.2V) 4.2 - 8.5 VDC, 1A maximum 5 VDC ± 5%, 1A maximum 5 VDC ± 5%, 0.1 A maximum 83.5 x 43.0 x 26.4 mm (WxDxH) Detection function Recommended thermal sensitive paper Medium Life Paper Long Life Paper *+5˚C to +40˚C printing density assurance rance (-25 to 70˚C capability) 3 FTP-628MCL353/354 s FUNCTION OF INTERFACE BOARD Item 1. 2. 3. 4. 5. 6. 7. Test print function Paper out detection Paper near end detection Platen open detection Thermal head temperature abnormality detection Blow-out fuse detection Head voltage abnormality detection 8. 9. 10. 11. 12. 13. 14. Item Cutter trouble detect Motor power saving function Mark detection function MCU operation abnormality detection Power ON/OFF sequence protection Motor over-current protection Hardware timer s DIMENSIONS 1. Printer mechanism FTP-628MCL353 FTP-628MCL354 83.5 1 26.4 12 38.6 58 at release at close 80.5 1 26.4 38.6 58 at release at close (26. 32 29.5 (26 3 (75) (67) 3 MAX 33.7 .9 45˚ 3 MAX 33.7 (75) (67) 45˚ (37.2) (37.2) Unit: mm Note: 1. Dimensions are nominal value (tolerance ±5 unless otherwise specified). 2. Platen unit (lever, platen, etc) moves by approximately 0.7mm toward paper insertion direction when platen is open. 4 FTP-628MCL353/354 2. Interface board Unit: mm 5 FTP-628MCL353/354 1. Connector (FPC) specification (CN4) (1) Connector Mechanical unit side: FPC connector Remote side (housing site): 52610-3090 (made by Molex) (2) Pin assignment on the mechanical side No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 PHK VSEN PHE SW1 SW2 VH VH DI CLK GND GND STB6 STB5 STB4 VDD TM TM STB3 STB2 STB1 GND GND LAT DO VH VH MT/A MT/A MT/B MT/B Signal I/O — I O O I I Head drive power I I I — Ground power supply for thermal head — I I I I O O I I I — Ground power supply for thermal head — I O I Power supply for thermal head I I I Stepping motor excitation signal I I 6 Contents Cathode for photo interruptor paper sensor power Emittor for photo interruptor Platen release switch Platen release switch Data in Synchronous clock for communication Thermal head energizing control signal Logic power Thermally sensitive resistor input termnial 1 Thermally sensitive resistor input termnial 2 Thermal head energizing control signal Data latch Data out FTP-628MCL353/354 Sensor (Photointerruptor) Platen unit Thermal head Motor FPC Connect terminal: surface side Connector No 30,29, .....................2,1 (FPC pin numbers) 2. Cutter (CN5) Connector on control circuit side: B4B-PH-K-S (J.S.T. or equivalent) No. 1 3 Signal CHP MT+ I/O I O Contents Cutter position detect signal Stepping motor coil excitation A No. 2 4 Signal GND MTI/O O Contents Logic ground Not connected Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: marcom@fcai.fujitsu.com Web: www.fcai.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: www.fceu.fujitsu.com Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #04-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com www.fcal.fujitsu.com © 2004 Fujitsu Components America, Inc. All company and product names are trademarks or registered trademarks of their respective owners. Rev. 11/15/2004. 7