FTR-C2GB012GB05

ULTRA MINIATURE RELAY SIGNAL RELAY FTR-C2 Series n FEATURES Dimensions of large contact gap relay Height: .8 mm maximum (THT) 2 mm maximum (SMT) Length: 20.2 mm maximum Width: 0 mm maximum l Conforms to IEC60950 / EN60950 / UL950/ CSA C22.2 No.950 spacing & high breakdown voltage l Recognized by UL/CSA and Bsi UL: File E6365 Vol. 2 Sec.4 CSA: Master contract 169663 Certificate 1088921 Clearance: 2.0 mm (between open contacts, coil and contacts, contact sets) Creepage: 2.0 mm (between open contacts, coil and contacts, contact sets) l HIGH RELIABILITY Bifurcated contacts l Low power consumption 300 mV l RoHS Compliant since production l RoHS compliant n ORDERING INFORMATION [Example] (a) (b) (c) (d) (e) (f) (g) FTR-C2 (a) C A 02 G -B 05* (b) (c) (d) (e) (f) (g) FTR-C2 C: Through hole type G: Surface mount type A: Standard type B: Latching type Nominal Voltage G: Silver alloy B: standard enclosing direction 05: 500 (standard) Series Name Termianl Apprearance Operation Function Coil Number Contact Material Relay enclosing direction Number of relays per reel Remarks: Actual marking on relay would not carry code FTR and be as below: Ordering code Actual marking FTR-C2CA03G → C2CA03G *only SMT version  FTR-C2 Series n COIL DATA CHART Coil Resistance (±10%) 30.0 Ω 83.3 Ω 480.0 Ω 1,920.0 Ω Nominal Operating Power (±10%) 300 mW 300 mW 300 mW 300 mW Standard type Model FTR-C2 ( ) A003G FTR-C2 ( ) A005G FTR-C2 ( ) A012G FTR-C2 ( ) A024G Single coil latching type Nominal Voltage 3 VDC 5 VDC 12VDC 24 VDC Coil Resistance (±10%) 60.0 Ω 167.0 Ω 960.0 Ω 3,840.0 Ω Nominal Operating Power (±10%) 150 mW 150 mW 150 mW 150 mW Nominal Voltage 3 VDC 5 VDC 12VDC 24 VDC Must Operate Voltage 2.25 VDC 3.75 VDC 9.00 VDC 18.00 VDC Must Release Voltage 0.3 VDC 0.5 VDC 1.2 VDC 2.4 VDC Model FTR-C2 ( ) B003G FTR-C2 ( ) B005G FTR-C2 ( ) B0012G FTR-C2 ( ) B024G Set Voltage Ω 2.25 VDC 3.75 VDC 9.00 VDC 18.00 VDC Reset Voltage 2.25 VDC 3.75 VDC 9.00 VDC 18.00 VDC Note: All values in the table are measured at 20˚C. 2 FTR-C2 Series n SPECIFICATIONS Item Arrangement Material Contact Resistance (initial) Max. Switching Power Max. Switching Voltage Max. Switching Current Coil Operating Temperature Max. Allowable Voltage Operate Time Release Time (without diode) Resistance (at 500 VDC) Between open contacts Dieelectric Strenght Insulation Surge Strength Mechanical Life Electrical (resistive load) Misoperation Endurance Misoperation Endurance Contact Rating Insulation Class IEC060950 UL1950 C22.2 No.950 EN60950 Working Voltage Pollution Degree Clearance Creepage Distance Between adjacent contacts Between coil and contacts Between open contacts Between adjacent contacts Between coil and contacts FTR-C2CA ( )G FTR-C2GA-( )G 2 F o rm C Silver alloy Max. 150m ohm (at 1A 6VDC) 37.5AV / 30W 250VAC, 220 VDC 1A -40˚ C to + 85˚ C (no frost) 150% nominal voltage (at 20˚ C) Max. 15ms (at nominal voltage, without bounce Max. 15ms (at nominal voltage, without bounce Min. 1,000M ohm 1,500VAC, 1 minute 1,500VAC, 1 minute 2,000VAC, 1 minute 2,500V (at10/700micros) 2,500V (at10/700micros) 2,500V (at10/700micros) 10x106 operations min. (at 10Hz) 100x103 operations min. at 1A, 30VDC, 0.5Hz 100x103 operations min. at 0.1A, 48VDC, 0.5Hz 100x103 operations min. at 0.3A, 125VDC, 0.5Hz 10 to 55 Hz at double amplitude of 3.3 mm 10 to 55 Hz at double amplitude of 5 mm Min. 300 m/s2 Min. 1,000 m/s2 0.3A 125 VAC 1A 30VDC 0.3 110VDC Supplementary Insulation 250 V 2 (outside) 2.0 mm (outside) 2.5 mm (outside) 1 (inside) 2.0 mm (inside) 2.0 mm (inside) 3 Time Value Vibration Resistance Shock Resistance UL / CSA FTR-C2 Series n DIMENSIONS AND SCHEMATICS Through hole type (1.135) 7.62 ±0.3 5.08 ±0.3 5.08 ±0.3 (1.115) 7.62 ±0.3 3.5 11.4 ±0.3 Unit: mm n TERMINAL DESIGNATIONS (Bottom view de-energized position) n RECOMMENDED MOUNTING PAD 8-O 0.9±0.1 (1.135) 7.62 ±0.1 5.08 ±0.1 5.08 ±0.1 Single Coil Polarity bar Type Latching (Bottom view reset position) SR Polarity bar S: shows polarity of set position R: shows polarity of reset position Unit: mm 4 7.62 ±0.1 (1.115) FTR-C2 Series n DIMENSIONS AND SCHEMATICS Surface mount type 11.7 ±0.3 0.25+.03 3 o ±.2 o (1.135) 7.62 ±0.3 5.08 ±0.3 5.08 ±0.3 7.62 ±0.3 10.8 ±0.3 0.3+0 -0.1 1.5 Unit: mm n TERMINAL DESIGNATIONS (Top view de-energized position) n R ECOMMENDED MOUNTING 3±0.1 1 ±0.1 1 ±0.1 1 ±0.1 1 ±0.1 3±0.1 Polarity bar 7.62 ±0.1 5.08 ±0.1 5.08 ±0.1 Single Coil Latching Type (Top view reset position) SR Polarity bar S: shows polarity of set position R: shows polarity of reset position Unit: mm 5 8.9±0.1 FTR-C2 Series n RECOMMENDED SOLDERING CONDITIONS (TEMPERATURE PROFILE) IRS (Infrared Reflow Soldering) Temperature (C) T3 T2 T1 preheating soldering T 3 = 245C max. T 2 = 200C max. cooling T 1 = 165C max. Note: 1.Temperature profiles show the tempera- ture of PC board surface. 2. Please perform soldering test with your actual PC board before mass production, since the temperatures of PC board surfaces vary according to the size of PC board, status of parts mounting and heating method. 0 120 sec maximum 30 sec Max. 6 FTR-C2 Series RoHS Compliance and Lead Free Relay Information 1. General Information Relays produced after the specific date code that is indicated on each data sheet are lead-free now. Most of our signal and power relays are lead-free. Please refer to Lead-Free Status Info. (http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf) l Lead free solder paste currently used in relays is Sn-3.0Ag-0.5Cu. l All signal and most power relays also comply with RoHS. Please refer to individual data sheets. Relays that are RoHS compliant do not contain the 5 hazardous materials that are restricted by RoHS directive (lead, mercury, chromium IV, PBB, PBDE). l It has been verified that using lead-free relays in leaded assembly process will not cause any problems (compatible). l “LF” is marked on each outer and inner carton. (No marking on individual relays). l To avoid leaded relays (for lead-free sample, etc.) please consult with area sales office. l We will ship leaded relays as long as the leaded relay inventory exists. Note: Cadmium was exempted from RoHS on October 2, 2005. (Amendment to Directive 2002/95/EC) l 2. Recommended Lead Free Solder Profile l Recommended solder paste Sn-3.0Ag-0.5Cu amd Sm-3.0 Cu-Ni (only FTR-B3 and FTR-B4 from February 2005. Reflow Solder condtion for SMT Peak Temp.: max. 250 C 250 Temperature ( C) 220 Pre-heating Cooling Soldering Flow Solder condtion: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C soler bath Solder by Soldering Iron: 0 30 30 Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. 90~20 sec. max. 20 sec. 20~30 sec. (duration) We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical realys. SnAgCu and SnCuNi solder is known as low risk of tin whisker. No considerable length whisker was found by our in-house test.  4. Tin Whisker l FTR-C2 Series Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 4, Japan Tel: (8-3) 5449-00 Fax: (8-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (-408) 45-4900 Fax: (-408) 45-490 Email: marcom@fcai.fujitsu.com Web: http://www.fujitsu.com/us/services/edevices/components/ Europe Fujitsu Components Europe B.V. Diamantlaan 25 232 WV Hoofddorp Netherlands Tel: (3-23) 556090 Fax: (3-23) 5560950 Email: info@fceu.fujitsu.com Web: http://www.fujitsu.com/emea/services/components/ Asia Pacific Fujitsu Components Asia Ltd. 02E Pasir Panjang Road #04-0 Citilink Warehouse Complex Singapore 8529 Tel: (65) 635-8560 Fax: (65) 623-302 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ ©2005 Fujitsu Components America, Inc. All rights reserved. All trademarks or registered trademarks are the property off their respective owners. Fujitsu Components America does not warrant that the content of datasheet is error free. In a continuing effort to improve our products Fujitsu Components America, Inc. reserves the right to change specifications/datasheets without prior notice. Rev. 11/18/2005. 8