FTR-F1AD1.5V

POWER RELAY 2 POLES - 5A Low Profile Type FTR-F1 Series ■■ FEATURES • Low profile (height: 16.5mm) • DPST/DPDT 5A • High insulation • • • (due to its reinforced insulation construction) Insulation Distance (between coil and contacts): 8mm min. Dielectric strength : 5,000 VAC Surge strength : 10,000 V Pin configuration compatible to VB UL, CSA, VDE, CQC recognized RoHS compliant (Please see page 6 for more information) ■■ Part Numbers [Example] (a) (b) (c) FTR-F1 (a) - A (b) Relay type Contact configuration Coil type / enclosure (d) Coil rated voltage (e) Contact material / TV type (f) Special type A (c) 005 (d) FTR-F1 A C A D 005 V T Nil RG V (e) - RG (f) : FTR-F1 series : 2 form A (SPST-NO) : 2 form C : Standard type (530mW) : High sensitivity type (400mW contact material V type only) : 1.5....110VDC Coil rating table at page 3 : Gold plated silver alloy(standard type) : Gold plated silver alloy (TV-3 rating type, only for 2 form A standard coil type) : Standard type : Transparent cover type Actual marking does not carry the type nameL "FTR" E.g.: Ordering code: "FTR-F1AA005V", actual marking: "F1AA005V" 1 FTR-F1 Series ■■ Specifications Item Standard type F1 (A, C) A ()V 2 form A (DPST-NO) 2 form C Contact Configuration data Construction Material Resistance Contact rating Max. carrying current Timing data Life Insulation Surge strength Coil to contacts Creepage 8mm Voltage 250V Pollution 3 Category Other Vibration resis- Misoperation tance Endurance Shock resistance Misoperation Endurance Dimensions / weight Sealing without bounce, no diode without bounce, no diode At rated load At rated load 10000V / 1.2 x 50μs standard wave 8mm Material group No frost 3000VAC (50/60Hz), 1 minute Clearance EN61810-1, VDE0435 Remarks / conditions Single Movable: Gold plate silver tin oxide (AgSnO2) Stationary: Silver tin oxide Max.100mΩ at 6VDC, 1A Initial 5A, 250VAC / 24VDC Resistive 7A 400VAC, 300VDC 1250VA / 120W 10 mA, 5VDC 530mW, 110V type: 550mW 400mW 260mW, 110V type: 270mW 225mW -40ºC ~ +75ºC (at rated voltage) -40ºC ~ +70ºC (Transparent cover type, -RG) Operate Max. 15ms Release Max. 5ms Mechanical Min. 20 x 10⁶ operations Electrical AC contact rating Min. 100 x 103 operations (resistive) DC contact rating Min. 100 x 103 operations Lamp load (TV-3) 25 x 103 operations min. Insulation resistance Min. 1000MΩ at 500VDC Dielectric Open contacts 1000VAC (50/60Hz), 1 minute strength Coil contact 5000VAC (50/60Hz), 1 minute Adjecent contacts : 2 form A (DSDT-NO) Sensitive type F1 (A, C) D ()V 2 form A (DPST-NO) 2 form C (DPDT) Max. switching voltage Max. switching power Min. switching load *1 Rated power (20oC) Operate power (20oC) Operating temperature range Coil *1 TV-3 rating F1 AA ( ) T III a C / 250V (reference voltage) (VDE 0110b) 10Hz ~ 55Hz ~ 10Hz single amplitude 0.825mm 10Hz ~ 55Hz ~ 10Hz single amplitude 1.65mm Min. 100m/s² (11 ± 1ms) Min. 1,000m/s² (6 ± 1ms) 12.8 x 29.0 x 16.5 mm / approx. 12.0g Flux proof RTII Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental contions and expected reliability levels. 2 FTR-F1 Series ■■ Coil Data 530mW standard type Coil code Rated Coil Voltage Coil Resistance +/-10% Must Operate Voltage* Must Release Voltage* (VDC) (Ω) (VDC) (VDC) 1.5 1.5 4.2 1.05 0.15 005 5 47 3.5 0.5 006 6 68 4.2 0.6 009 9 155 6.3 0.9 012 12 270 8.4 1.2 018 18 610 12.6 1.8 024 24 1,100 16.8 2.4 048 48 4,400 33.6 4.8 060 60 6,800 42.0 6.0 110 110 22,000 77.0 11.0 Rated Power (mW) 530 550 400mW high sensitive type Coil code Rated Coil Voltage Coil Resistance +/-10% Must Operate Voltage* Must Release Voltage* (VDC) (Ω) (VDC) (VDC) 1.5 1.5 5.6 1.125 0.15 003 3 22.5 2.25 0.3 005 5 62 3.75 0.5 006 6 90 4.5 0.6 009 9 202 6.75 0.9 012 12 360 9 1.2 024 24 1,440 18 2.4 048 48 5,760 36 4.8 Rated Power (mW) 400 Note: All values in the table are valid at 20oC and zero contact current, unless otherwise specified. * : Specified operated values are valid for pulse wave voltage. Note: Please use at rated coil voltage. Please refer to characteristic data and set up adequate voltage in case of use at over voltage. Care shall be taken on the heat generated on PC board when maximum carrying current exceeds 10A. Please perform the confirmation test with actual conditions. ■■ Safety Standards Type UL Compliance UL 508 CSA C22.2 No. 14 File No. LR 40304 VDE CQC IEC/EN61810-1 EN60065 clause 14.6.1 (FTR-F1AA ( )T) EN60335-1 clause 15.3; 16.3; 29.1; 29.2; 29.3 EN60730-1 clause 12.2; 13.2; 20.1; 20.2; 20.3 GB/T21711.1, GB15092.1 (No.17002164350) Contact rating Flammability: UL 94-V-0 (plastics) 5A, 24VDC (resistive) 5A, 250VAC (resistive) 1/6 hp, 125VAC 1/4 hp, 250VAC Pilot duty: C300 Pilot duty: R300 (FTR-F1CA( )V) TV-3 (FTR-F1AA( )T) (except for -RG type) 5A, 250 VAC (cosφ=1) 2A, 250 VAC (cosφ=0.4) 5A, 24VDC (0ms) 2A/32A, 250VAC (FTR-F1AA( )T) 5A, 250VAC (FTR-F1CA( )V) 3 FTR-F1 Series ■■ Characteristic Data (Reference) * Characteristic data is not a guaranteed value, but measured values of samples from production line. 0A L/R=7ms L/R=15ms 4 FTR-F1 Series ■■ Dimensions • Dimensions FTR-F1A type FTR-F1C type * Dimensions of the terminals do not include thickness of pre-solder. • Schematics (BOTTOM VIEW) FTR-F1A FTR-F1C • PC Board Mounting Hole Layout (BOTTOM VIEW) FTR-F1A FTR-F1C ( ): Reference value Unit: mm * Tolerance of PC board mounting hole layout : ±0.1 unless otherwise specified. Cautions • • • • All values mentioned in this datasheet are provided under ideal conditions. Please perform the confirmation test before actual use. Reflow soldering is prohibited. Do not use relays in the atmosphere with sulfide gas, chloride gas or nitric oxide. Contact resistance may increase. Do not use silicon or silicon-containing product or materials near relays. It may cause contact failure. 5 FTR-F1 Series GENERAL INFORMATION 1. ROHS Compliance • All relays produced by Fujitsu Components are compliant with RoHS directive 2011/65/EU including amendments. • Use of Cadmium in electrical contacts is exempted as per Annex III of the RoHS directive 2011/65/EU. • Please consider expiry date of exemption. Relays with Cadmium containing contacts are not to be used for new designs. All relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/downloads/MICRO/fcai/relays/lead-free-letter.pdf Characteristic data is not guaranteed values, but measured values of samples from production line. • 2. Recommended lead free solder condition • Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. • Recommended solder for assembly: Sn-3.0Ag-0.5Cu. Flow Solder Condition: Pre-Heating: maximum 120˚C within 90 sec. Soldering: dip within 5 sec. at 255˚C ± 5˚C solder bath Relay must be cooled by air immediately after soldering Solder by Soldering Iron: Soldering Iron: 30-60W Temperature: maximum 350-360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity • Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers • Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 6 FTR-F1 Series Fujitsu Components International Headquarter Offices Japan FUJITSU COMPONENT LIMITED Shinagawa Seaside Park Tower 19F, 12-4, Higashi-shinagawa 4-chome, Shinagawa-ku, Tokyo,140-0002, Japan Tel: (81-3) 3450-1682 Fax: (81-3) 3474-2385 Email: fcl-contact@cs.jp.fujitsu.com Web: www.fujitsu.com/jp/fcl/ Asia Pacific FUJITSU COMPONENTS ASIA, LTD. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components North and South America FUJITSU COMPONENTS AMERICA, INC 2290 North First Street, Suite 212 San Jose, CA 95131, USA Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: us.fujitsu.com/components China FUJITSU ELECTRONIC COMPONENTS (SHANGHAI) CO., LTD. Unit 4306, InterContinental Center 100 Yu Tong Road, Shanghai 200070, China Tel: (86-21) 3253 0998 Fax: (86-21) 3253 0997 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components Europe FUJITSU COMPONENTS EUROPE B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: www.fujitsu.com/uk/components Hong Kong FUJITSU COMPONENTS HONG KONG CO., LTD Unit 506, Inter-Continental Plaza No.94 Granville Road, Tsim Sha Tsui, Kowloon, Hong Kong Tel: (852) 2881-8495 Tex: (852) 2894-9512 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components/ Korea FUJITSU COMPONENTS KOREA LIMITED Alpha Tower #403, 645 Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, 13524 Korea Tel: (82) 31-708-7108 Fax: (82) 31-709-7108 Email: fcal@sg.fujitsu.com www.fujitsu.com/sg/products/devices/components/ ©2018 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. July 17th, 2018 7