FTR-F1L

FTR-K1 SERIES POWER RELAY 2 POLES - 8A Polarized Latching Relay FTR-F1L Series n FEATURES l l Low profile (height: 16.5mm) High insulation Insulation distance (between coil and contacts): 8mm min. Dielectric strength: 5KV Surge strength: 10KV l Plastic materials - UL94 Flammability class V-0 l Cadmium free relay l RoHS compliant Please see page 4 for more information n PARTNUMBER INFORMATION [Example] (a) (b) (c) (d) (e) (f) (g) FTR-F1 L D (a) (b) (c) C (d) A 012 R (e) (f ) (g) FTR-FL: FTR-FL Series L Nil D A C A 012 R : Latching type :  Coil : 2 Coil : 2 form A : 2 form C : Standard, 400mW (1Coil) 600mW (2 Coil) : 5.....24 VDC Coil data table at page 2 : 8A Relay type Operating function Coil type Contact configuration Coil power Coil rated voltage Contact rating Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-F1LDCA012R FTR-F1LDCA012R Actual marking: F1LDCA012R Actual marking: F1LDCA012R  FTR-K1 SERIES FTR-F1L SERIES n SPECIFICATION Item Contact Data Configuration Construction Material Resistance (initial) Contact rating Max. carrying current Max. switching voltage Max. switching power Min. switching load * Life Coil Data Mechanical Electrical Rated power (20 °C) Operating temperature range Timing Data Insulation Set / reset (at nominal voltage) Coil exitation Resistance (initial) Open contacts Dielectric strength Surge strength Clearance Creepage Other Vibration resistance Shock Weight Endurance Endurance Adjacent contacts Coil to contacts coil to contacts FTR-FL 2 form A, 2 form C Single AgSnO2 ≤ 100mOhm at 1A, 6VDC 8A, 250VAC / 24VDC 8A 400VAC, 300VDC 2,000VA, 192W 10mA, 5VDC 3 x 106 operations minimum 50 x 103 operations minimum 1 coil : 400mW 2 coils: 600mW -40 °C to +85 °C (no frost) ≤ 15ms (no diode, no bounce) ≥ 30ms (no diode, no bounce) ≥ 1,000MOhm at 500VDC 1,000VAC, 1min. 50/60Hz 3,000VAC, 1min. 50/60Hz 5,000VAC, 1 min. 50/60Hz 10,000V/ 1.2 x 50µs standard wave 8mm 8mm Misoperation >1µs 10 to 55Hz double amplitude 1.65 mm 10 to 55Hz double amplitude 3.3 mm Min. 1,000m/s2 (6±1ms) Approximately 13g Misoperation >1µs Min. 200m/s2 (11±1ms) * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental contions and expected reliability levels. n COIL DATA Coil Code 5 2 24  coil Operating range Min. VDC 3.5 8.4 16.8 Max. VDC 9 21.2 42.2 Coil Resistance +/- 10% (Ohm) 62.5 360 1,440 Min. VDC 3.5 8.4 16.8 2 coils Operating range Max. VDC 9 21.2 42.2 Coil Resistance +/- 10% (Ohm) 41.7 240 960 Note: All values in the table are valid for 20°C and zero contact current. * Specified operate values are valid for pulse wave voltage. 2 FTR-K1 SERIES FTR-F1L SERIES n COIL POLARITY Version Coil terminal division Set Reset 4 - +  coil 7 + + 4 5 2 coils 6 7 + n DIMENSIONS 3 FTR-K1 SERIES FTR-F1L SERIES RoHS Compliance and Lead Free Information 1. General Information All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. l Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) l All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. l 2. Recommended Lead Free Solder Profile l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 4. Tin Whiskers l 4 FTR-K1 SERIES FTR-F1L SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://us.fujitsu.com/components Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ ©2009 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. November 5, 2009 5