FTR-G1CN010W1

FTR-K1 SERIES COMPACT POWER RELAY 1 POLE - 25A (For Automotive Applications) FTR-G1 Series FEATURES  Compact for high density packaging  High contact capacity with proven contact material (min. 100,000 operations, 14V, 25A)  Coil power savings (640mW nominal achived with state-ofthe-art magnetic analysis/design)  Ease of PCB layout (all terminals on perimeter, coil and contact terminals separated)  Lower noise (57dB average at 5cm)  RoHS compliant Please see page 5 for more information   APPLICATIONS  Power window  Door lock  Tilt steering  Sunroof  Power seat Wiper/IWW Retractable antenna  PARTNUMBER INFORMATION [Example] (a) (b) (c) (d) (e) FTR-G1 (a) C (b) N (c) 010 (d) W1 (e) FTR-G1: FTR-G1 Series C N 010 W1 : 1 form C : 0.25mm : 9....12VDC Coil rating table at page 3 : Silver-tin oxide indium Relay type Contact configuration Contact gap Coil rated voltage Contact material Actual marking does not carry the type name: "FTR" E.g.: Ordering code: FTR-G1CN010W1 Actual marking: G1CN010W1 1 FTR-K1 SERIES FTR-G1 SERIES SPECIFICATION Item Contact Data Configuration Material Contact voltage drop Contact rating Max. carrying current *1 Max. switching voltage Max. switching current Min. switching load * 2 Life Mechanical 1 form C Silver-tin oxide indium (AgSnO2) Max. 100mV at 1A, 6VDC (after stabilization) 25A at 14VDC (locked motor load) 25A/1 hour (25 °C, 100% rated coil voltage) 16VDC (reference) 35A (reference) 1A, 6VDC Min. 1 x 106 operations * Min. 100 x 103 operations, 14VDC, 25A inrush power window motor (1 operation: 1 forward and 1 reverse) * Min. 100 x 103 operations 14VDC, 20A inrush door locked motor 640mW 237mW -40 °C to +85 °C (no frost) Max. 10 ms (without bounce) Max. 5 ms (without bounce, no diode) Min. 100MΩ at 500VDC Open contacts Between coil and contacts Misoperation Misoperation Endurance 500VAC , 1 min. 500VAC, 1 min. 10 to 55Hz double amplitude 1.5mm 100m/s² minimum (10G) 1,000m/s² minimum (100G) Approximately 3.5 g Plastic sealed cat III FTR-G1 Electrical Coil Data Rated power Operate power Operating temperature range Timing Data Insulation Operate (at nominal voltage) Release (at nominal voltage) Resistance (initial) Dielectric withstanding voltage Other Vibration resistance Shock Weight Sealing * 1 Need to consider the heat to PCB when max. current is more than 10A * 2 Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2 FTR-G1 SERIES FTR-K1 SERIES COIL RATING Coil Code 009 010 012 Rated Coil Voltage (VDC) 9 10 12 Coil Resistance +/- 10% (Ohm) 126 160 225 Must Operate Voltage (VDC) * 5.4 6.8 (at 85 °C) 6.5 8.2 (at 85 °C) 7.3 9.2 (at 85 °C) Note: All values in the table are valid for 20°C and zero contact current, unless otherwise indicated. * Specified operate values are valid for pulse wave voltage. Coil Power at Must Release Voltage Nominal Voltage (VDC) * (W) 0.75 0.8 1 0.64 REFERENCE DATA 3 FTR-G1 SERIES FTR-K1 SERIES DIMENSIONS Mounting hole layout (bottom view) Schematics Marking (example) Tube Unit: mm 4 FTR-K1 SERIES FTR-G1 SERIES RoHS Compliance and Lead Free Information 1. General Information     All automotive relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) All our automotive relays are lead-free. Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. 2. Recommended Lead Free Solder Profile  Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity  Moisture Sensitivity Level standard is not applicable to through hole mounted electromechanical relays, unless otherwise indicated. 4. Tin Whiskers  Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 5 FTR-K1 SERIES FTR-G1 SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://us.fujitsu.com/components Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ ©2011 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. January 11, 2011 6