FTR-G1CN012W1-PH-F

FTR-K1 SERIES COMPACT POWER RELAY 1 POLE - 25A (For Automotive Applications) FTR-G1 Series n FEATURES Compact for high density packaging High contact capacity with proven contact material (min. 100,000 operations, 14V, 25A) l Coil power savings (640mW nominal achived with state-ofthe-art magnetic analysis/design) l Ease of PCB layout (all terminals on perimeter, coil and contact terminals separated) l Lower noise (60dB average at 5cm) l Plastic sealed l Through hole reflow capable type available l RoHS compliant Please see page 6 for more information l l n APPLICATIONS Power window l Power seat Door lock l Wiper/IWW l Tilt steering l Retractable antenna l Sunroof l l n PARTNUMBER INFORMATION [Example] FTR-G1 C N 010 W1 (a) (b) (c) (d) (e) FTR-G1 - RW (f) (a) Relay type : FTR-G1 Series (b) Contact configuration C : 1 form C (c) Contact gap N : 0.25 mm (d) Coil rated voltage 010 : 9.....12 VDC Coil rating table at page 3 (e) Contact material / TV type W1 : Silver-tin oxide indium (f) Soldering Nil RW : Standard (Flow soldering) : Reflow capable (THR) Actual marking does not carry the type name: "FTR" E.g.: Ordering code: FTR-G1CN010W1 Actual marking: G1CN010W1 1 FTR-K1 SERIES FTR-G1 SERIES n SPECIFICATION Item FTR-G1 Standard Contact Data Configuration 1 form C Material Silver-tin oxide indium (AgSnO2) Contact voltage drop Max. 100mV at 1A, 6VDC (after stabilization) Contact rating Max. carrying current Coil Data Timing Data Insulation 25A at 14VDC (locked motor load) *1 16VDC (reference) Max. switching current 35A (reference) 2 1A, 6VDC Mechanical Min. 10 x 106 operations Electrical * Min. 100 x 103 operations, 14VDC, 25A inrush power window motor * Min. 100 x 103 operations 14VDC, 20A inrush door locked motor Rated power 625 to 643mW Operate power 237mW Operating temperature range -40 °C to +85 °C (no frost) Operate (at nominal voltage) Max. 10 ms (without bounce) Release (at nominal voltage) Max. 5 ms (without bounce) Resistance (initial) Min. 100MΩ at 500VDC Dielectric withstanding voltage Other 25A/1 hour (25 °C, 100% rated coil voltage) Max. switching voltage Min. switching load * Life Reflow capable Vibration resistance Shock Open contacts -40 °C to +125 °C (no frost) 500VAC , 1 min. Between coil and 500VAC, 1 min. contacts Misoperation 10 to 200Hz, 44m/s2 (4.5G), constant acceleration Endurance 10 to 200Hz, 44m/s2 (4.5G), constant acceleration Misoperation 100m/s² minimum (11+/-1ms) Endurance 1,000m/s² minimum (6+/-1ms) Weight Approximately 3.5 g Sealing Plastic sealed cat III * 1 Need to consider the heat to PCB when max. current is more than 10A * 2 Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. Care shall be taken on the heat generated on PC board when maximum carrying current exceeds 10A. Please perform the confirmation test with actual conditions. 2 FTR-K1 SERIES FTR-G1 SERIES n COIL RATING Standard type Coil Code Rated Coil Voltage (VDC) Coil Resistance +/10% (Ohm) Must Operate Voltage (VDC) * Must Release Voltage (VDC) * 009 9 126 5.4 0.7 6.8 (at 85 °C) 0.9 (at 85 °C) 6.5 0.8 8.2 (at 85 °C) 1.0 (at 85 °C) 7.3 1.0 9.2 (at 85 °C) 1.3 (at 85 °C) 010 012 10 12 160 225 Reflow capable type Coil Code Rated Coil Voltage (VDC) Coil Resistance +/10% (Ohm) Must Operate Voltage (VDC) * Must Release Voltage (VDC) * 009 9 126 5.4 0.7 7.6 (at 125 °C) 1.1 (at 125 °C) 6.5 0.8 9.2 (at 125 °C) 1.0 (at 125 °C) 7.3 1.0 10.3(at125 °C) 1.4 (at 125 °C) 010 012 10 12 160 225 Note: All values in the table are valid for 20 °C and zero contact current, unless otherwise indicated. * Specified operate values are valid for pulse wave voltage. 3 FTR-K1 SERIES FTR-G1 SERIES n CHARACTERISTIC DATA (Characteristic data is not guaranteed value but measured values of samples from production line.) Distribution of operate/release voltage 100 Distribution of contact resistance 100 FTR-G1CN010W1 n=100 Release Operate 40 20 Duration time (sec.) 60 60 40 10 20 30 40 50 60 70 0 80 100 10 20 Coil voltage 16VDC max. 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 FTR-G1CN012W1 10A Allowable voltage e ltag t Mus -40 -20 0 20 40 60 40 50 60 70 80 100 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 20 l te vo 40 60 Vibration resistance 1000 Acceleration (m/s) 0.64W 70 at : 25 ℃ 60 50 0A 40 30 44 m/s2 Automotive standard Printed surface 50 Y 10 FTR-G1CN012W1 n=10 800 Make (coil energized) Break (coil de-energized) 600 10 20 Applied time (min.) 30 Y Z' X' X Z Y' 1 0 Printed surface 400 2 10 10 1000 200 20 1 Shock resistance Chattering >1msec. (Coil de-energized, Y direction) 100 70 Coil power (W) FTR-G1CN012W1 n=10 FTR-G1CN012W1 60 25A 20A 10A 0A 100 10 0.1 80 100 120 Coil temperature rise 100 50 試料：FTR-G1CN012W1 (25℃) 500 tage pera 0 40 1000 Allowable voltage -40 -20 30 Coil temperature rise 0A to Mus 20 16A FTR-G1CN012W1-RW Ambient temperature (°C) 80 10 Contact current (A) Coil voltage 16VDC max. Ambient temperature (° C) 90 0 80 Ambient temperature vs voltage (reflow capable type) 0A o ate v oper 30 Contact resistance (mΩ) Coil voltage (VDC) Coil voltage (VDC) 85℃ 10 0 Temperature rise (°C) 0 Ambient temperature vs voltage (standard type) Temperature rise (°C) 25℃ 1000 Failure mode: Make contact open by short coil Nominal voltage multiplying factor (%) 0 FTR-G1CN012W1 20 Impact (m/s₂) 0 FTR-G1CN010W1 n=100 80 Distribution (%) Distribution (%) 80 Contact current 10000 1 10 100 1000 Frequency (Hz) 10000 0 Time: 6±1ms, half sign curve Detection chattering >1msec. Coil voltage: rated voltage or 0V X X Y Y' Z Z' Direction 4 FTR-K1 SERIES FTR-G1 SERIES n DIMENSIONS l Dimensions (Standard type) l Dimensions (Reflow capable type) 13.7+0.5 3.5 3 0.4 0.9 14+0.5 13.5+0.5 6.6+0.5 6.6 +0.5 13.7+0.5 1 8 1 3.5 l Schematics (BOTTOM VIEW) 2 3 8 3.5 2.5 2.5 4.7 4.7 l PC board mounting hole layout (BOTTOM VIEW) 5 2-φ1+0.1 -0 2-φ1.5 -0 2.5±0.1 4.7±0.1 (2.05) +0.1 1 (0.95) (1) 4 φ1.7 +0.1 -0 8 ±0.1 * Dimensions of the terminals do not include thickness of pre-solder. * Tolerance of PC board mounting hole layout : ±0.1 unless otherwise specified. 3.5±0.1 ( ) : Reference Unit: mm Cautions • • • • All values mentioned in this datasheet are provided under ideal conditions. Please perform the confirmation test before actual use. Reflow soldering is prohibited for standard type. Do not use relays in the atmosphere with sulfide gas, chloride gas or nitric oxide. Contact resistance may increase. Do not use silicon or silicon-containing product or materials near relays. It may cause contact failure. 5 FTR-K1 SERIES FTR-G1 SERIES RoHS Compliance and Lead Free Information 1. General Information All relays produced by Fujitsu Components are compliant with RoHS directive 2011/65/EU including amendments. l Cadmium as used in electrical contacts is exempted from the RoHS directives. As per Annex III of directive 2011/65/EU. l All relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/downloads/MICRO/fcai/relays/lead-free-letter.pdf l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. l 2. Recommended Lead Free Solder Condition l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder Condition: Pre-heating: maximum 120˚C within 90 sec. Soldering: dip within 5 sec. at 255˚C ± 5˚C solder bath Relay must be cooled by air immediately after soldering Re-Flow Solder Condition: Solder by Soldering Iron: Soldering Iron 30-60W Temperature: maximum 350-360˚C Duration: maximum 3 sec. Applicable for FTR-G1CNxxx-W1-RW only We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 6 FTR-K1 SERIES FTR-G1 SERIES Fujitsu Components International Headquarter Offices Japan FUJITSU COMPONENT LIMITED Shinagawa Seaside Park Tower 19F, 12-4, Higashi-shinagawa 4-chome, Shinagawa-ku, Tokyo,140-0002, Japan Tel: (81-3) 3450-1682 Fax: (81-3) 3474-2385 Email: fcl-contact@cs.jp.fujitsu.com Web: www.fujitsu.com/jp/fcl/ Asia Pacific FUJITSU COMPONENTS ASIA, LTD. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components North and South America FUJITSU COMPONENTS AMERICA, INC 2290 North First Street, Suite 212 San Jose, CA 95131, USA Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: us.fujitsu.com/components China FUJITSU ELECTRONIC COMPONENTS (SHANGHAI) CO., LTD. Unit 4306, InterContinental Center 100 Yu Tong Road, Shanghai 200070, China Tel: (86-21) 3253 0998 Fax: (86-21) 3253 0997 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components Europe FUJITSU COMPONENTS EUROPE B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: www.fujitsu.com/uk/components Hong Kong FUJITSU COMPONENTS HONG KONG CO., LTD Unit 506, Inter-Continental Plaza No.94 Granville Road, Tsim Sha Tsui, Kowloon, Hong Kong Tel: (852) 2881-8495 Tex: (852) 2894-9512 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components/ Korea FUJITSU COMPONENTS KOREA LIMITED Alpha Tower #403, 645 Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, 13524 Korea Tel: (82) 31-708-7108 Fax: (82) 31-709-7108 Email: fcal@sg.fujitsu.com www.fujitsu.com/sg/products/devices/components/ ©2018 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. June 07, 2018 7