FTR-H1CA012V

FTR-K1 SERIES NOT FOR NEW DESIGN POWER RELAY 1 POLE - 10A Low Profile Type FTR-H1 Series n FEATURES Working class: B (for IMQ)/ C (for VDE) Type of service: continuous duty l Low profile (height 16.5 mm) l 1 form A/ 1 form C 10 A, TV-5 rating available l Transparency cover type available l UL class B (130°C) wire class l High insulation in small package Insulation distance : 8 mm (between coil and contacts) Dielectric strength : 5,000 VAC Surge strength :10,000 V l Plastic materials - UL94 flame class V-0 UL CTI level class 2 l Plastic sealed relay, RT III l Pin configuration compatible to VS / FBR610 series l UL, CSA, BSI, VDE, SEMKO recognized l Conforms to FIMKO, DEMKO l RoHS compliant Please see page 6 for more information l l n PARTNUMBER INFORMATION [Example] (a) FTR-H1 A (a) (b) A 005 (c) (d) Relay type V - RG (e) (f ) FTR-H1 : FTR-H1 Series (b) Contact configuration A C (c) Coil type A D (d) Coil rated voltage 005 : 1 form A (SPST-NO) : 1 form C (SPDT) (e) Contact material / TV type V T : Gold plate silver tin oxide (standard type) : Gold plate silver tin oxide (TV-5 rating type, 1 form A standard) RG : Transparent cover type (f) Special type : Standard type (530mW) : High sensitive type (400mW - V type only) : 5....48VDC Coil rating table at page 3 Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-H1AA005V Actual marking: H1AA005V 1 FTR-H1 FTR-K1SERIES SERIES NOT FOR NEW DESIGN n SPECIFICATION Item Contact Data Life FTR-H1 (AC) A ( ) FTR-H1 AA ( ) T FTR-H1 (AC) D ( ) V Configuration 1 form A (SPST-NO) 1 form C (SPDT) 1 form A (SPST-NO) 1 form A (SPST-NO) 1 form C (SPDT) Construction Single Material Movable: gold plate silver tin oxide, stationary: silver tin oxide Resistance (initial) Max. 100mOhm at 1A, 6VDC Contact rating 10A, 250VAC, 30VDC Max. carrying current 14A Max. switching voltage 400VAC, 300VDC Max. switching power 2,500VA, 300W Min. switching load* 10 mA, 5VDC Mechanical Min. 20 x 106 operations Electrical Coil Data Timing Data Insulation Min. 100 x 103 operations DC load Min. 100 x 103 operations Lamp load (TV-5) - Min. 25 x 103 operations - Rated power 530 mW 400 mW Operate power 260 mW 230 mW Operating temperature range -40 °C to +75 °C (no frost) (refer to characteristic data) -40 °C to +70 °C (transparent cover -RG type) Operate (at nominal voltage) Max. 10ms (without bounce) Release (at nominal voltage) Max. 5ms (no diode) Resistance (initial) Min. 1,000MOhm at 500VDC Dielectric strength Surge strength Open contacts 1,000VAC (50/60Hz) 1min Contacts to coil 5,000VAC (50/60Hz) 1min Coil to contacts 10,000V / 1.2 x 50µs standard wave Clearance 8mm Creepage 8mm EN61810-1, VDE0435 Other AC load Vibration resistance Shock Voltage 250V Pollution degree 3 Material group IIIa Category C / 250V Misoperation 10 to 55Hz double amplitude 1.65mm Endurance 10 to 55Hz double amplitude 3.3mm Misoperation Min. 100m/s2 (11±1ms) Endurance Min. 1,000m/s2 (6±1ms) Weight Approximately 12g Sealing Sealed RT III * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental contions and expected reliability levels. 2 FTR-K1SERIES SERIES FTR-H1 NOT FOR NEW DESIGN n COIL RATING Standard type (530 mW) Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must ReleaseMax. Coil Voltage Voltage (VDC) (VDC) * 005 5 47 3.5 0.5 8.2 006 6 68 4.2 0.6 9.9 009 9 155 6.3 0.9 14.8 012 12 270 8.4 1.2 19.8 024 24 1,100 16.8 2.4 39.6 048 48 4,400 33.6 4.8 79.2 Rated Power (mW) 530 High sensitive type (400 mW) Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must ReleaseMax. Coil Voltage Voltage (VDC) (VDC) * 005 5 62 3.75 0.5 9.7 006 6 90 4.5 0.6 11.7 009 9 202 6.75 0.9 17.5 012 12 360 9 1.2 23.4 024 24 1,440 18 2.4 46.8 048 48 5,760 36 4.8 93.6 Rated Power (mW) 400 Note: All values in the table are valid for 20°C and zero contact current. * Specified operate values are valid for pulse wave voltage. n SAFETY STANDARDS Type Compliance Contact rating UL UL 508 Flammability: UL 94-V0 (plastics) E63614 CSA C22.2 No. 14 LR 40304 VDE 0435, 0631, 0700, 0860 40015054 10A, 30 VAC (resistive) 10A, 250 VAC (resistive) 12A, 250VAC (resistive) 1/3 HP, 125VAC 1/2 HP, 125VAC Pilot duty: B300 TV-5 (only T type) 10A, 250 VAC (cosφ=1), 3A, 250 VAC (cosφ=0.4) 10 250 VAC (0ms) 5/80A, 250 VAC (T type) Complies with SEMKO, BSI, CQC,NEMKO, DEMKO, FIMKO 3 NOT FOR NEW DESIGN FTR-K1SERIES SERIES FTR-H1 n CHARACTERISTIC DATA n REFERENCE DATA 4 FTR-K1SERIES SERIES FTR-H1 NOT FOR NEW DESIGN n DIMENSIONS Dimensions FTR-H1C type n l Schematics (BOTTOM VIEW) 3 PC board mounting hole layout (BOTTOM VIEW) 4 5 (2.65) l 4-Ø1.3 NO 7.5 NC COM 1 2 Orientation mark (2.1) 3.5 3.5 20 3 5 (2.65) FTR-H1A type 4-Ø1.3 7.5 NO COM 2 Orientation mark 1 (2.1) 20 3.5 Unit: mm 5 NOT FOR NEW DESIGN FTR-K1SERIES SERIES FTR-H1 RoHS Compliance and Lead Free Information 1. General Information All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. l Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) l All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. l 2. Recommended Lead Free Solder Profile l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 6 NOT FOR NEW DESIGN FTR-K1SERIES SERIES FTR-H1 Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://us.fujitsu.com/components Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ ©2010 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. July 22, 2010 7