FTR-K1AK024W-HT

FTR-K1 SERIES POWER RELAY 1 POLE - 16A 105ºC FTR-K1 Series n FEATURES l l RoHS compliant l l l l l l Low profile (height: 15.7mm) HIGH ISOLATION Insulation Distance (between coil and contacts): 10mm min. Dielectric strength: 5KV Surge strength: 10KV Low coil power (400mW) Cadmium free contacts SAFETY STANDARDS UL, CSA, VDE, SEMKO approved UL, CSA TV-5 rating approved ( form A type) RoHS Compliant UL F class isolation wire VDE Glow-wire ignitablility test 775 (IEC60335-1) approved n ORDERING INFORMATION [Example] (a) (b) (c) (d) (e) (f) FTR-K C K 005 W – HT (a) (b) (c) (d) (e) (f ) FTR-K : FTR-K Series A C K 005 08 048 W T HT :  form A (SPST-NO) :  form C (SPDT) : Standard (400 mW) / flux free : 5 VDC, : 8 VDC : 48VDC 006 : 6VDC, 022 :022VDC 009 : 9VDC 024 : 24VDC, 02 : 2VDC 028 : 28VDC Series Name Contact Arrangement Coil Type / Enclosure Nominal Voltage Contact Material / TV type Special Designation : AgSnO2 ( form C) : AgSnO2 / TV-5 rated (form A TV-5) : 05ºC Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-K1CK012W Actual marking: K1CK012W  FTR-K1 SERIES n PART NUMBERS 400mW type Ordering Part Number FTR-KAK005T-HT FTR-KAK006T-HT FTR-KAK009T-HT FTR-KAK02T-HT FTR-KAK08T-HT FTR-KAK022T-HT FTR-KAK024T-HT FTR-KAK028T-HT FTR-KAK048T-HT FTR-KCK005W-HT FTR-KCK006W-HT FTR-KCK009W-HT FTR-KCK02W-HT FTR-KCK08W-HT FTR-KCK022W-HT FTR-KCK024W-HT FTR-KCK028W-HT FTR-KCK048W-HT K: 430 mW C:  form C K: 400 mW FTR-K K: 430 mW A:  form A K: 400 mW Series Contact Coil Power Coil Voltage 5 6 9 2 8 22 24 28 48 5 6 9 2 8 22 24 28 48 W: AgSnO2 T: AgSnO2 Contact Material n COIL DATA CHART Coil Voltage 005 006 009 02 08 022 024 028 048 Nominal Voltage (VDC) 5 6 9 2 8 22 24 28 48 Max. Coil Voltage* 12.2 VDC 14.7 VDC 22.0 VDC 29.4 VDC 44.1 VDC 53.9 VDC 58.8 VDC 68.6 VDC 117.6 VDC Coil Must Operate Must Resistance Voltage*2 Release Voltage*2 (±0%) 62 Ω 90 Ω 202 Ω 360 Ω 810 Ω 1,210 Ω 1,440 Ω 1,960 Ω 5,360 Ω 3.5 VDC 4.2 VDC 6.3 VDC 8.4 VDC 12.6 VDC 15.4 VDC 16.8 VDC 19.6 VDC 33.6 VDC 0.5 VDC 0.6 VDC 0.9 VDC 1.2 VDC 1.8 VDC 2.2 VDC 2.4 VDC 2.8 VDC 4.8 VDC 430 400 Nominal Power (mW) Note: All values in the table are measured at 20°C. *1: No contact current at 20°C *2: Specified values are subject to pulse wave voltage 2 FTR-K1 SERIES n SPECIFICATIONS Item Contact Arrangement Material Resistance (initial) Rating Maximum Carrying Current*1 Maximum Inrush Current Maximum Switching Rating Maximum Switching Voltage Minimum Switching Load*2 Coil Nominal Power (at 20ºC) Operate Power (at 20ºC) Operating Temperature Time Value Life Operate (without diode) Release (without diode) Mechanical Electrical Other Vibration Resistance Shock Resistance Weight AC Contact rating DC contact rating Misoperation Endurance Misoperation Endurance FTR-K AK ( ) T-HT Standard  form A AgSnO2 Maximum 100 mΩ at 1 A, 6 VDC 6 A, 250 VAC / 24 VDC 6 A 80A (20ms) 250VAC 4,000 VA / 384W 440 VAC / 300VDC 0 mA 5 VDC 400mW (at 430mW 48V coil) 200 mW (20mW at 48V coil) -40ºC to +05ºC (no frost) Maximum 15ms (at nominal voltage, no bounce) Maximum 5ms (at nominal voltage, no bounce) 20 x 106 operations minimum 100 x 103 operations min. 100 x 103 operations min. 50 x 103 operations min. 30 x 103 operations min. FTR-K CK ( )W-HT Standard  from C 10 to 55 Hz, at double amplitude of 0.7 mm 10-55Hz, at double amplitude of 1.5 mm Min. 100m/s2 (±ms) Approximately 13g Min. 1,000m/s2 (6±ms) * Need to consider the heat from PCB when max. current is more than 10A. *2 Minimum switching loads mentioned above are reference values. Please perform the confirmation test with the actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 3 FTR-K1 SERIES n INSULATION Item Resistance (initial) Dielectric Strength open contacts coil and contacts FTR-K Minimum 1,000 MΩ 1 min. 1,000 VAC (50/60 Hz) 1 min. 5,000 VAC (50/60 Hz) 1 min. 0,000 V 0 mm / 0 mm 250 V 3 IIIa 1.2 x 50µs standard wave Note at 500 VDC Surge Voltage (coil and contact) Clearance/Creepage Insulation (DIN EN61810-1 VDE0435) Voltage Pollution Isolation material group Isolation category / Reference voltage (VDE00b) C / 250 V n SAFETY STANDARDS Type UL Compliance UL 508 E63614 CSA C22.2 No. 14 LR 40304 Contact rating FTR-KCK ( ) W-HT Flammability: UL 94-V0 (plastics) 16A, 277 VAC (resistive) 105ºC 6A, 24 VDC (resistive) 05ºC 1 HP, 277VAC 105ºC /2 HP, 25VAC 05ºC TV-5, 20VAC, 25,000 cycles, 05ºC Pilot duty: A300 105ºC 6A, 24VDC (resistive) 16A, 277 VAC (resistive) 20A 277VAC (resistive) 1 HP, 277VAC /2 HP, 25VAC TV-5, 20VAC 25,000 cycles Pilot duty: A300 250VAC, 16 (3)A 40T85 5A/80A 250VAC 40T85 6A, 24 VDC (resistive) 05ºC 16A, 277 VAC (resistive) 105ºC 1 HP, 277VAC 105ºC /2 HP, 25VAC 05ºC /8 HP, 25VAC 05ºC Pilot duty: B300 105ºC 6A, 24VDC (resistive) 16A, 277 VAC (resistive) 20A 277VAC (resistive) 1 HP, 277VAC /2 HP, 25VAC /8 HP, 25VAC Pilot duty: B300 FTR-KAK ( ) T-HT VDE 0435, 0631, 0700, 0860 SEMKO EN 6058-:992 and A EN 61095:1993 and A+A Complies with NEMKO, DEMKO, FIMKO 4 FTR-K1 SERIES n CHARACTERISTIC DATA Coil Temperature Rise 00 Nominal voltage multiplying factor Operating Range 2.5 FTR-K 2 0A 1.5 6A Maximum Switching Power 50 Temperature Rise (deg.) 90 80 70 60 50 40 30 20 0 0 0 0.2 0.4 0.6 0.8  1.2 0A 0A 6A Switching Current (A) 20 0 5 2  0.5 0.2 0.1 0 20 AC resistive FTR-K  mu te volta st opera ge (hot coil) 0.5 must ope 0 20 rate volta 40 ge (cool c oil) DC resistive 60 80 00 Coil Power (W) Ambient temperature (ºC) 50 00 200 500 000 Contact Voltage (V) Distribution of Operation & Release Voltage FTR-KCK02W n=200 Operate Release Service Life (03 operations) Service Life (03 operations) 000 500 300 200 00 50 30 20 0 0 2 4 Life Curve 250VAC resistive 24VDC resistive FTR-KAK 000 500 300 200 00 50 30 20 0 Life Curve 250VAC resistiveFTR-KCK 250VAV cosφ=0.7 24VDC resistive 250VAC cosφ=0.4 24VDC τ=7ms 00 90 80 Distribution (%) 250VAC cosφ=0.7 70 60 50 40 30 20 DC24V τ=7ms AC250V cosφ=0.4 DC24V τ=15ms 24VDC τ=15ms 6 8 0 2 4 6 8 20 Contact Current Load (A) 0 Contact Current Load (A) 2 4 6 8 0 2 4 6 8 20 0 0 0 0 20 30 40 50 60 70 80 Nominal Voltage Multiplying Factor Distribution of Operation & Release Time FTR-KCK02W n=200 Operate 00 90 80 Distribution of Contact Resistance 00 90 80 FTR-KCK02W n=200 Make Break Distribution (%) Distribution (%) 9 0 70 60 50 40 30 20 0 0 0 1 2 3 4 5 6 Release 70 60 50 40 30 20 0 7 8 0 Time (ms) 0 Contact Resistance (mΩ) 0 20 30 40 50 5 FTR-K1 SERIES n DIMENSIONS l Dimensions FTR-KAK ( ) T-HT 29 +0.3 12.7 +0.3 l Schematics (BOTTOM VIEW) 5 6 COM 7 8 NO 15.7 +0.3 COM 4 3 2  NO Orientation mark φ 0.45 (2.6) 3.3 0.3 20 5 0.5 0.9 2.6 7.5 0.9 l PC board mounting hole layout (BOTTOM VIEW) (2.6) 2-Ø ±0.1 20 4-Ø1.3 (2.6) 5 l Dimensions FTR-KCK ( ) W-HT 29 +0.3 12.7 +0.3 l Schematics (BOTTOM VIEW) 5 6 NC COM 7 8 NO 15.7 +0.3 NC COM 4 3 2  NO Orientation mark 3.3 φ 0.45 0.5 0.3 5 (2.6) 20 5 0.5 0.9 2.6 7.5 0.9 l PC board mounting hole layout (BOTTOM VIEW) (2.6) 2-φ1 ±0.1 20 6-φ1.3 -0 5 5 (2.6) 7.5 Unit: mm 7.5 6 FTR-K1 SERIES RoHS Compliance and Lead Free Relay Information 1. General Information Relays produced after the specific date code that is indicated on each data sheet are lead-free now. All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info. (http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf) l Lead free solder paste currently used in relays is Sn-3.0Ag-0.5Cu. l All signal and power relays also comply with RoHS. Please refer to individual data sheets. Relays that are RoHS compliant do not contain the 5 hazardous materials that are restricted by RoHS directive (lead, mercury, chromium IV, PBB, PBDE, DecaBDE). l It has been verified that using lead-free relays in leaded assembly process will not cause any problems (compatible). l “LF” is marked on each outer and inner carton. (No marking on individual relays). l To avoid leaded relays (for lead-free sample, etc.) please consult with area sales office. l We will ship leaded relays as long as the leaded relay inventory exists. Note: Cadmium was exempted from RoHS on October 21, 2005. (Amendment to Directive 2002/95/EC) l 2. Recommended Lead Free Solder Profile l Recommended solder paste Sn-3.0Ag-0.5Cu. Solder condition Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays. Dipped SnAgCu solder is known as low risk tin whisker. No considerable length whisker was found by our in house test. 4. Tin Whisker l 7 FTR-K1 SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 4, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://www.fujitsu.com/us/services/edevices/components/ Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 8529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ ©2008 Fujitsu Components America, Inc. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. Fujitsu Components America or its affiliates do not warrant that the content of datasheet is error free. In a continuing effort to improve our products Fujitsu Components America, Inc. or its affiliates reserve the right to change specifications/datasheets without prior notice. Rev. July 21, 2008. 8