FTR-K1CK012W

FTR-K1 SERIES POWER RELAY 1 POLE - 16A 80A Inrush type FTR-K1 Series n FEATURES Peak 80A inrush current (1 form A type) Low profile (height: 15.7mm) l HIGH INSULATION Insulation distance (between coil and contacts): 10mm min. Dielectric strength: 5KV Surge strength: 10KV l Class F coil wire l Low coil power (400mW) l Cadmium free contacts l SAFETY STANDARDS UL, CSA, VDE, SEMKO approved UL, CSA TV-5 rating approved (1 form A type) l Flux proof, RTII l RoHS compliant Please see page 6 for more information l l n PARTNUMBER INFORMATION [Example] (a) FTR-K1 C (a) (b) K 012 (c) (d) Relay type W - BG (e) (f ) FTR-K1 : FTR-K1 Series (b) Contact configuration A C (c) Coil type K (d) Coil rated voltage 012 : 1 form A (SPST-NO) : 1 form C (SPDT) (standard type "K" only) (e) Contact material / TV type W T : AgSnO2 (1 form C contact type only) : AgSnO2 / TV-5 rated (1 form A / TV-5 contact type only) (f) Special type Nil BG : Standard type (without gold plate) : Gold plated 3µm : Standard type (400mW / Flux proof) : 5....110VDC Coil rating table at page 3 Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-K1CK012W Actual marking: K1CK012W 1 FTR-K1SERIES SERIES FTR-K1 n SPECIFICATION Item Contact Data FTR-K1 AK ( ) T Standard FTR-K1 CK ( ) W Standard Configuration 1 form A 1 form C Construction Single Material AgSnO2 Resistance (initial) Max. 100mOhm at 1A, 6VDC Contact rating (resistive) Max. carrying current 20A Max. inrush current 80A (20ms) 250VAC (only make contact) Max. switching voltage 440VAC / 300VDC Max. switching power 4,000VA / 384W Min. switching load Life 16A, 250VAC / 24VDC *1 *2 100mA, 5VDC Min. 20 x 106 operations Mechanical Electrical AC contact rating Min. 100 x 103 operations Min. 50 x 103 operations DC contact rating Min. 100 x 103 operations Min. 30 x 103 operations Peak Inrush (80A) Min. 10 x 103 operations (only make contact) Lamp load (UL TV-5) Min. 25 x 103 operations Coil Data Timing Data Insulation Rated power (20 °C) 400mW (430mW at 48V coil) Operate power (20 °C) 200mW (210mW at 48V coil) Operating temperature range -40 °C to +85 °C (no frost) Operate (at nominal voltage) Max. 15ms (without bounce) Release (at nominal voltage) Max. 5ms (without bounce, no diode) Resistance (initial) Min. 1,000MOhm at 500VDC Dielectric strength Surge strength Open contacts 1,000VAC (50/60Hz) 1min Contacts to coil 5,000VAC (50/60Hz) 1min Coil to contacts 10,000V / 1.2 x 50µs standard wave Clearance 10mm Creepage 10mm EN61810-1, VDE0435 Other Min. 25 x 103 operations (only make contact) Vibration resistance Shock Voltage 250V Pollution degree 3 Material group III a Category C / 250V (Reference voltage) (VDE0110b) Misoperation≥1us 10 to 55Hz double amplitude 0.7mm Endurance 10 to 55Hz double amplitude 1.5mm Misoperation≥1us 100m/s² (11 ± 1ms) Endurance 1,000m/s² (6 ± 1ms) Weight Approximately 13g Sealing Flux proof, RTII * 1: Need to consider the heat from PCB when max. current is more than 10A. * 2: Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental contions 2 FTR-F4 SERIES FTR-K1SERIES SERIES FTR-K1 n COIL RATING Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must ReleaseMax. Coil Voltage Voltage (VDC) (VDC) * 005 5 62 3.5 0.5 12.2 006 6 90 4.2 0.6 14.7 009 9 202 6.3 0.9 22 012 12 360 8.4 1.2 29.4 018 18 810 12.6 1.8 44.1 022 22 1,210 15.4 2.2 53.9 024 24 1,440 16.8 2.4 58.8 028 28 1,960 19.6 2.8 68.6 048 48 5,360 33.6 4.8 117.6 060 60 8,570 42.0 6.0 147.0 110 110 28,800 77.0 11.0 269.5 Rated Power (mW) 400 430 420 Note: All values in the table are valid for 20°C and zero contact current. * Specified operate values are valid for pulse wave voltage. n SAFETY STANDARDS Type Compliance Contact rating UL UL 508 FTR-K1CK ( ) W E63614 FTR-K1AK ( ) T Flammability: UL 94-V0 (plastics) 16A, 277VAC/24VDC (resistive) 20A, 277VAC (resistive) 1 HP, 277VAC 1/2 HP, 125VAC 1/8 HP, 125VAC TV-5, 120VAC, 25,000 cycles (only make contact) Pilot duty: B300 16A, 24VAC (resistive) 16A, 277VAC (resistive) 20A, 277VAC (resistive) 1 HP, 277VAC 1/2 HP, 125VAC TV-5, 120VAC 25,000 cycles Pilot duty: A300 CSA C22.2 No. 14 LR 40304 VDE 0435, 0631, 0700, 0860, 40013848 SEMKO EN 61058-1:1992 and A1 250VAC, 16 (3)A 40T85 EN 61095:1993 and A1+A11 5A/80A 250VAC 40T85 (only make contact) 16A, 250VAC (cosφ=1), 85˚C 3.5A, 250VAC (cosφ=0.4), 85˚C 16 A 24VDC (0ms), 85˚C 5A/80A, 250VAC 10,000 times, 85˚C (only make contact) Complies with NEMKO, DEMKO, FIMKO 3 FTR-K1SERIES SERIES FTR-F4 SERIES FTR-K1 n CHARACTERISTIC DATA 4 FTR-K1SERIES SERIES FTR-F4 FTR-K1 n DIMENSIONS l Dimensions l Schematics (BOTTOM VIEW) FTR-K1AK ( ) T l l Dimensions l PC board mounting hole layout (BOTTOM VIEW) Schematics (BOTTOM VIEW) FTR-K1CK ( ) W l PC board mounting hole layout (BOTTOM VIEW) Unit: mm 5 FTR-K1SERIES SERIES FTR-F4 SERIES FTR-K1 RoHS Compliance and Lead Free Information 1. General Information All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. l Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) l All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. l 2. Recommended Lead Free Solder Profile l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 6 FTR-F4 SERIES FTR-K1SERIES SERIES FTR-K1 Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://us.fujitsu.com/components Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ ©2010 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. July 28, 2010 7