FTR-K1KW

FTR-K1 SERIES POWER RELAY 1 POLE - 16A Sealed Type FTR-K1 Series n FEATURES l l 1 pole 16A l 1 form A / 1 form C l Coil sensitive 400mW l High insulation in small package (between coil and contacts) - Insulation distance: 10mm min. - Dielectric strength: 5,000VAC - Surge strength: 10,000V l Conform to UL1446 Class F coil insulation system l Cadmium free contacts l RoHS compliant Please see page 7 for more information n PARTNUMBER INFORMATION FTR-K1 C K 05 W - KW 0 [Example] (a) (b) (c) (d) (e) (f) (a) (b) (c) (d) (e) (f) Relay type Contact configuration Coil type Coil rated voltage Contact material Special type FTR-K1: FTR-K1 Series A C K 005 W : 1 form A : 1 form C : Standard type (400mW) / flux free : 5.....48 VDC Coil rating table at page 3 : AgSnO2 KW : Sealed type Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-K1CK005W-KW Actual marking: K1CK005W-KW 1 FTR-K1 SERIES FTR-K1 SERIES n SPECIFICATION 16A type Item Contact Data Configuration Construction Material Resistance (initial) Contact rating (resistive) Max. carrying current *1 Max. switching voltage Max. switching power Min. switching load *2 Life Mechanical Electrical Coil Data Timing Data Insulation Rated power (20 °C) Operating temperature range Operate (at nominal voltage) Release (at nominal voltage) Resistance (initial) Dielectric strength Surge strength Clearance Creepage EN61810-1, VDE0435 Voltage Pollution degree Material group Category Other Vibration resistance Shock Weight Endurance Endurance Open contacts Contacts to coil Coil to contacts Rating resistive load FTR-K1 CK ( ) W-KW 1 form C Single AgSnO2 FTR-K1 AK ( ) W-KW 1 form A Maximum 100mΩ at 1A, 6VDC 16A, 250VAC 20A 440VAC 4,000VA 100mA, 5VDC 20 x 106 operations minimum 10 x 103 operations minimum 400 / 430 mW -40 °C to +85 °C (no frost) ≤ 15ms (no bounce, no diode) ≤ 5ms (no bounce, no diode) ≥ 1,000MOhm at 500VDC 1,000VAC (50/60Hz) 1min 5,000VAC (50/60Hz) 1min 10,000V / 1.2 x 50µs standard wave 10mm 10mm 250 3 III a C / 250V 10 to 55Hz double amplitude 1.5mm 1,000m/s² (6 ± 1ms) Approximately 13g 20 x 103 operations minimum Misoperation≥1us 10 to 55Hz double amplitude 0.7mm Misoperation≥1us 100m/s² (11 ± 1ms) * 1: Need to consider the heat from PCB when max. current is more than 10A. * 2: Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2 FTR-K1 SERIES FTR-K1 SERIES n COIL RATING Coil Code 005 006 009 012 018 022 024 028 048 Rated Coil Coil Resistance Voltage +/- 10% (Ohm) (VDC) 5 6 9 12 18 22 24 28 48 62 90 202 360 810 1210 1440 1960 5360 Must Operate Must ReleaseMax. Coil Voltage Voltage Voltage (VDC) (VDC) * (VDC) * 3.5 4.2 6.3 8.4 12.6 15.4 16.8 19.6 33.6 0.5 0.6 0.9 1.2 1.8 2.2 2.4 2.8 4.8 12.2 14.7 22.0 29.4 44.1 53.9 58.8 68.6 117.6 430 400 Rated Power (mW) Note: All values in the table are valid for 20°C and zero contact current. * Specified operate values are valid for pulse wave voltage. n SAFETY STANDARDS Type UL VDE Compliance 508 E 63614 0435; 40013848 Contact rating Flammability: UL 94-VII (plastics) UL-94-V0 16A, 250VAC cos Ø=1 85 °C 10.000 ops. 3 FTR-K1 SERIES FTR-K1 SERIES n CHARACTERISTIC DATA 4 FTR-K1 SERIES FTR-K1 SERIES 5 FTR-K1 SERIES FTR-K1 SERIES n DIMENSIONS l Dimensions Drilling plan (BOTTOM VIEW) l l Wiring diagram (BOTTOM VIEW) Unit: mm Note: In case of 1 form A, there is no "stationary" contact arm. 6 FTR-K1 SERIES FTR-K1 SERIES RoHS Compliance and Lead Free Information 1. General Information All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. l Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) l All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. l 2. Recommended Lead Free Solder Profile l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 4. Tin Whiskers l 7 FTR-K1 SERIES FTR-K1 SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://us.fujitsu.com/components Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ ©2010 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. April 13, 2010 8