FTR-K3JB012W-HC

FTR-K1 SERIES POWER RELAY 1 POLE - 20A Heavy Load FTR-K3 Series n FEATURES SPST 20A and #250 tab terminal type is also available Low coil power (780mW) l Type of service: continuous duty l Cadmium free contacts l SAFETY STANDARDS UL, CSA, VDE,CQC approved l RoHS compliant Please see page 6 for more information l l n PARTNUMBER INFORMATION FTR-K3 (a) J (b) B (c) [Example] (a) (b) (c) (d) (e) (f) 012 (d) W - HC (e) (f ) FTR-K3 : FTR-K3-Series A J B 012 W Nil LS HC : 1 form A (SPST-NO) (PCB terminal) : 1 form A (SPST-NO) (Tab terminal) : Standard type (780mW) : 5.....48 VDC Coil rating table at page 3 : Silver alloy : Standard type (20A) : High isolation type (20A) : High current type (25A) Relay type Contact configuration Coil type Coil rated voltage Contact material Option Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-K3AB012W Actual marking: K3AB012W 1 FTR-K1 SERIES FTR-K3 SERIES n SPECIFICATION Item Contact Data Configuration Construction Material Resistance (initial) Contact rating (resistive) Max. carrying current Max. switching current *¹ Max. switching voltage Max. switching power Min. switching load *² Life Mechanical Resistive load FTR-K3 1 form A Single Silver alloy Max. 100mΩ at 1A, 6VDC 20A, 250VAC 25A 25A 250VAC 6,250VA 100 mA, 5VDC Min. 2 x 106 operations Min. 100 x 103 operations Min. 200 x 103 operations (250VAC inrush 80A cosφ=0.7 cut off 20A cosφ=0.9) Min. 200 x 103 operations (250VAC inrush 80A cosφ=0.7 cut off 20A cosφ=0.9) Min. 200 x 103 operations (250VAC inrush 80A cosφ=0.7 cut off 25A cosφ=0.9) 20A, 250VAC 25A, 250VAC FTR-K3-LS FTR-K3-HC Electrical Motor load Inverter load Coil Data Rated power (at 20 °C) Operate power (at 20 °C) Operating temperature range Timing Data Insulation Operate (at nominal voltage) Release (at nominal voltage) Resistance Dielectric strength Surge strength Other Open contacts Contacts to coil Coil to contacts Misoperation Endurance Misoperation Endurance Clearance/creepage distance Vibration resistance Shock Weight Sealing Min. 30 x 103 operations 100VAC, inrush 200A / cut off 20A 780 mW 380 mW -40 °C to +60 °C (no frost) Max. 20ms (without bounce) Max. 10ms (no diode, without bounce) Min. 1,000MΩ at 500VDC 1,000VAC (50/60Hz) 1min 5,000VAC (50/60Hz) 1min 8,500V / 1.2 x 50µs standard wave 6.4mm / 9.5mm 8.0mm / 9.5mm 6.4mm / 9.5mm 10 to 55Hz double amplitude 1.5 mm 10 to 55Hz double amplitude 1.5 mm Min. 200m/s² (11 ± 1ms) Min. 1,000m/s² (6 ± 1ms) Approximately 25 g Flux proof, RTII * 1 Need to consider the heat from PCB when max. current is more than 10A * 2 Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2 FTR-K1 SERIES FTR-K3 SERIES n COIL RATING Coil Code 005 006 009 012 018 024 048 Rated Coil Voltage (VDC) 5 6 9 12 18 24 48 Coil Resistance +/- 10% (Ohm) 32 46 105 185 415 740 2,955 Must Operate Voltage (VDC) * 3.5 4.2 6.3 8.4 12.6 16.8 33.6 Must ReleaseVoltage (VDC) * 0.5 0.6 0.9 1.2 1.8 2.4 4.8 780 Rated Power (mW) Note: All values in the table are valid for 20°C and zero contact current. * Specified operate values are valid for pulse wave voltage. n SAFETY STANDARDS Compliance UL508 No. E63614 Contact rating FTR-K3 FTR-K3-LS FTR-K3-HC 25A, 277VAC (resistive at 60 °C) 1hp, 125VAC (at 60 °C) 2hp, 277VAC (100,000 ops. at 60 °C) 25A, 277VAC (resistive) 1hp, 125VAC 2hp, 277VAC (100,000 ops.) 25A, 250VAC (cos φ=1) 60 °C 25A, 250VAC 20A, 250VAC, 40T60/ 20 (13.33) A 250VAC, 40T60 20/200A 100VAC, 40T60 20A, 277VAC (resistive at 60 °C) 1hp, 125VAC (at 60 °C) 2hp, 277VAC (100,000 ops. at 60 °C) Type UL CSA C22.2 No. 14 No. LR40304 20A, 277VAC (resistive) 1hp, 125VAC 2hp, 277VAC (100,000 ops.) 20A, 250VAC (cos φ=1) 60 °C VDE IEC61810-1 CQC GB15092-1 GB8898 GB/T21711.1 No. 04001009179 EN61058-1 EN61095 20A, 250VAC SEMKO - - TUV EN61810-1 IEC61810-1 20A, 250VAC (cos φ=1) 60 °C - 3 FTR-K1 SERIES FTR-K3 SERIES n CHARACTERISTIC DATA 4 FTR-K1 SERIES FTR-K3 SERIES FTR-K3-HC type Electrical life tests (resistive load) n DIMENSIONS FTR-K3 AB type l Dimensions l Schematics l PC board mounting hole layout (BOTTOM VIEW) FTR-K3 JB type l Dimensions l Schematics l PC board mounting hole layout (BOTTOM VIEW) 5 FTR-K1 SERIES FTR-K3 SERIES RoHS Compliance and Lead Free Information 1. General Information l l l l All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. 2. Recommended Lead Free Solder Profile l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: Duration: maximum 360˚C maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to through hole mounted electromechanical relays, unless otherwise indicated. 4. Tin Whiskers l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 6 FTR-K1 SERIES FTR-K3 SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://us.fujitsu.com/components Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ ©2011 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. July 13, 2011 7