FTR-K3WG

FTR-K1 SERIES POWER RELAY 1 POLE - 25A - 1.5mm contact gap FTR-K3-WG Series n FEATURES l l 1 pole, 25A 1 Form A l Contact gap 1.5mm l High insulation in small package (between coil and contact) - Insulation distance: Clearance > 6.5mm Creepage > 9.5mm - Dielectric strength: 5,000VAC - Surge strength: 8,500V l Flammability UL94V-0 (plastics) l RoHS compliant Please see page 5 for more information Contains no lead and features cadmium-free contacts n PARTNUMBER INFORMATION [Example] FTR-K3 A B 012 W - WG (a) (b) (c) (d) (e) (f) (a) (b) (c) (d) (e) (f) Relay type Contact configuration Coil type Coil rated voltage Contact material Version FTR-K3-WG : FTR-K3-WG Series A B 012 W WG : 1 form A : Standard (0.78W) : 5.....48 VDC Coil rating table at page 3 : Silver tin oxide : Contact gap 1.5mm Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-K3AB012W-WG Actual marking: K3AB012W K3AB012W WG marked on the relay  FTR-K3-WG SERIES FTR-K1 SERIES n SPECIFICATION Item Contact Data Configuration Material Resistance (initial) Contact rating Max. carrying current Max. switching power Max. switching voltage Max. switching current Min. switching load (reference) Life Mechanical FTR-K3-WG 1 form A Silver tin oxide ≤ 100mOhm at 1A, 6VDC 25A / 250VAC (resistive) 25A 6,250VA 250VAC 25A 100mA, 5VDC 2 x 106 operations minimum 25A 250VAC, 100 x 103 operations resistive Electrical Inrush 200A / break 25A 100VAC: 30 x 103 operations (inverterload) Inrush 80A cosφ 0.7 / 20A cosφ 0.9 ; 250VAC 2 x 105 operations (motorload) Coil Data Rated power (at 20 °C) Operate power (at 20 °C) Operating temperature range Timing Data Insulation Operate (at nominal voltage) Release * Contact gap (initial) Resistance Dielectric strength Surge strength Other Vibration resistance Shock resistance Weight Open contacts Coil and contacts Coil to contacts Misoperation Endurance Misoperation Endurance Approximately 0.78W Approximately 0.38W -40 °C to +60 °C (no frost) ≤ 20ms (no bounce) ≤ 10ms (no diode, no bounce) Minimum 1.5 mm ≥ 1,000MOhm at 500VDC 1,000VAC, 1min. 5,000VAC, 1min. 8,500V / 1.2 x 50µs standard wave 10 to 55Hz double amplitude 1.5 mm 10 to 55Hz double amplitude 1.5 mm Min. 200m/s² (11 ± 1ms) Min. 1,000m/s² (6 ± 1ms) Approximately 25 g * Use a varistor as a protective circuit against reverse surge in the relay coil. A varistor is connected parallel to the coil. The reverse blocking voltage should be about 3 times the value of the power surge voltage. 2 FTR-K1 SERIES FTR-K3-WG SERIES n COIL RATING Coil Code 005 006 009 012 08 024 048 Rated Coil Coil Resistance Voltage +/- 10% (Ohm) (VDC) 5 6 9 12 8 24 48 32 46 105 185 415 740 2,955 Must Operate Must ReleaseVoltage Voltage (VDC) * (VDC) * 3.5 4.2 6.3 8.4 12.6 16.8 33.6 0.5 0.6 0.9 1.2 .8 2.4 4.8 Approx. 0.78 Rated Power +/- 10% (W) Note: All values in the table are measured at 20°C and zero contact current * Specified values are measured with pulse wave voltage n SAFETY STANDARDS Type UL Compliance UL 508 Contact rating 20A, 277VAC, resistive 1HP, 125VAC 1HP, 277VAC 20A, 250VAC (cosφ=1) 60°C VDE 0435 3 FTR-K1 SERIES FTR-K3-WG SERIES n DIMENSIONS l Dimensions l Schematics (BOTTOM VIEW) l PC board pattern (BOTTOM VIEW) Unit: mm 4 FTR-K1 SERIES FTR-K3-WG SERIES RoHS Compliance and Lead Free Information 1. General Information All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. l Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) l All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. l 2. Recommended Lead Free Solder Profile l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. l 5 FTR-K1 SERIES FTR-K3-WG SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://us.fujitsu.com/components Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ ©2009 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. October 15, 2009 6