JS-24-K

POWER RELAY 1 POLE - 8A Medium Load Control JS Series ■■ FEATURES • UL class B (130°C) coil wire insulation • 1 form A (SPST-NO) or 1 form C (SPDT) contact • Low profile and space saving • • • • • • Height: 12.5 mm - Mounting space: 290 mm2 High sensitivity in small package Operating power 110 to 140 mW Nominal power 220 to 290 mW High insulation in small package Insulation distance : 8.0 mm (between coil and contacts) Dielectric strength : 5,000 VAC Surge strength : 10,000 V Plastic materials UL 94 flame class V-0 UL CTI level class 2 Plastic sealed type Various contact material options RoHS compliant (Please see page 6 for more information) ■■ Part Numbers [Example] JS (a) - 12 (b) (a) (b) (c) Relay type Contact rated voltage (d) Contact material (e) (f) Enclosure Construction (g) Gold plating (h) Special type Coil configuration Note: Actual marking omits the hyphen (-) or (*) *: V3 is marked at different position on the relay E.g.: Ordering code: JS-12F Actual marking: JS12F-K M (c) F (d) - K (e) T (f) - V3* (g) - RW (h) JS 12 Nil M D F N K Nil T Nil V3 : JS series : 5....60VDC (Coil rating table at page 3) : 1 form C (SPDT) : 1 form A (SPST-NO) : Silver nickel : Gold flash silver nickel : Gold flash : Plastic sealed type : 3.2mm : 5.0mm (only JS-MN) : Standard (0.1micron gold flash with Nil, N and F contact) : 3.0μ gold plating for lower current applications (available with Nil and N contact, not available for T, 5.0mm type) V1 : 1.0μ gold plating for lower current applications (avaialble with N contact, not available for T, 5,0mm type) Nil : Standard RW : Reflow capable (through hole reflow) (not available for V1, V3) 1 JS Series ■■ Specifications Item Contact Configuration data Construction Plating Material Resistance Contact rating Max. carrying current Coil Timing data Life Insulation Max. switching voltage Max. switching power Min. switching load *1 Rated power (20oC) Operate power (20oC) Operating temperature range Operate Release Mechanical Electrical AC contact rating (resistive) DC contact rating Insulation resistance Dielectric Open contacts strength Coil contact Surge strength Coil to contacts 8mm Voltage 250V Pollution 3 Vibration resis- Misoperation tance Endurance Shock resistance Misoperation Endurance Dimensions / weight Sealing : 6VDC, 1A Resistive No frost without bounce without bounce, no diode At rated load At rated load 10000V / 1.2 x 50μs standard wave Creepage Category Remarks / conditions 5000VAC (50/60Hz), 1 minute 8mm Material group *1 400VAC / 300VDC (-RW; 400VAC / 150VDC) 2000VA / 192W 100 mA, 5VDC 10 mA, 5VDC 220 - 290mW 110 - 140mW -40ºC ~ +85ºC (at rated voltage) Max. 10ms Max. 5ms Min. 20 x 10⁶ operations Min. 50 x 103 operations (AgSnO2) Min. 20 x 103 operations (AgNi) Min. 50 x 103 operations (AgSnO2) Min. 20 x 103 operations (AgNi) Min. 1000MΩ at 500VDC 1000VAC (50/60Hz), 1 minute Clearance EN61810-1, VDE0435 Other JS-( ) JS-( )D-K JS-( ) JS-( ) F/N-K N-K-V1 N-K-V3 1 form A (SPST-NO), 1 form C (SPDT) Single 0.1μ Au 1μ Au 3μ Au Plated Plated Plated See partnumber information Max.100mΩ Max.30mΩ 8A, 250VAC / 24VDC 10A III a C / 250V (reference voltage) (VDE 01106) 10Hz ~ 55Hz ~ 10Hz single amplitude 0.825mm 10Hz ~ 55Hz ~ 10Hz single amplitude 1.65mm Min. 100m/s² (11 ± 1ms) Min. 1,000m/s² (6 ± 1ms) Direction X, Y, Z, contact ON/OFF total 36 times Direction X, Y, Z, contact OFF total 18 times 10.0 x 29.0 x 12.5 mm / approx. 8.0g Plastic sealed Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental contions and expected reliability levels. 2 JS Series ■■ Coil Data Coil code Rated Coil Voltage Coil Resistance +/-10% Must Operate Voltage* Must Release Voltage* (VDC) (Ω) (VDC) (VDC) 005 5 112 3.5 0.5 006 6 160 4.2 0.6 009 9 360 6.3 0.9 012 12 660 8.5 1.2 018 18 1,455 12.7 1.8 024 24 2,350 16.8 2.4 048 48 8,000 33.4 4.8 060 60 12,500 41.7 6.0 Rated Power (mW) 225 220 225 245 290 Note: All values in the table are valid at 20oC and zero contact current, unless otherwise specified. * : Specified operated values are valid for pulse wave voltage. Note: Please use at rated coil voltage. Please refer to characteristic data and set up adequate voltage in case of use at over voltage. Care shall be taken on the heat generated on PC board when maximum carrying current exceeds 10A. Please perform the confirmation test with actual conditions. ■■ Safety Standards Type UL Compliance UL 508 CSA File No. E 56140 C22.2 No. 14 File No. LR 35579 VDE IEC/EN61810-1 EN60335-1 clause 15.3; 16.3; 29.1; 29.2; 29.3 EN60730-1 clause 12.2; 13.2; 20.1; 20.2; 20.3 EN60947-5-1 Appendix C CQC GB15092.1 CQC17001162883 Contact rating Flammability: UL 94-V-0 (plastics) Contact material: N D, F Nil, E 8A, 24VDC resistive 8A 24VDC 8A 24VDC 8A, 250VAC resistive (resistive) 100k (resistive) 100k 8A, 250VAC 8A, 250VAC (resistive) 100k (resistive) 100k 10A, 30VDC 10A, 30VDC (resistive) (resistive) 10A, 250VAC ( 10A, 250VAC resistive) (resistive) 1/4HP, 125VAC / 1/4HP, 125VAC / 250VAC 250VAC 1/3HP, 125VAC 1/3HP, 125VAC 1/2HP, 250VAC 1/2HP, 250VAC Pilot duty: C150, Pilot duty: A300, B300 B300 Pilot duty: 0.27A, C150, R300 250VDC 8A 250VAC (cos φ=1) JS-( )D-K, JS-( )F-K: 8A 24VDC (L/R=0ms) 6A, 250VAC, (cos φ=1) 8A, 24VDC (L/R=0ms) JS-( )MD-K, JS-( ) MF-K: 8A, 240VAC (cos φ=1) 8A, 24VDC (L/R=0ms) 10A 30VDC/250VAC (except -V3 type) 3 JS Series ■■ Characteristic Data (Reference) * Characteristic data is not guaranteed value but measured values of samples from production line. 4 JS Series ■■ Characteristic Data (Reference) * Characteristic data is not guaranteed value but measured values of samples from production line. 5 JS Series ■■ Dimensions • Dimensions JS-K 10＋0.3 29＋0.3 10＋0.3 22.1 5 -pre solder 4 -pre solder 1 (Spring terminal) 7.62 (2.1) 0.24 0.4 3.2 0.4 3.2 0.25 (Coil terminal) 0.8 3.3 0.8 0.24 0.4 3.2 3.3 4 -pre solder 29＋0.3 10＋0.3 22.1 (2.1) 12.5+0.3 12.5+0.3 12.5+0.3 29＋0.3 JS-MN-KT 4 -pre solder 5 -pre solder 1 (Spring terminal) 7.62 0.25 0.4 (Coil terminal) 5 0.4 0.8 3.3 JS-M-K 4 -pre solder (2.1) 18.9 1 (Spring terminal) 7.62 0.25 (Coil terminal) * Dimensions of the terminals do not include thickness of pre-solder. • Schematics (BOTTOM VIEW) JS-M-K JS-K 1 3 JS-MN-KT 1 NO 2 NO COM 5 1 3 COM COM 4 5 5 4 Orientation mark 3 NO NC 4 Orientation mark Orientation mark • PC Board Mounting Hole Layout (BOTTOM VIEW) 2 -φ1.5 22.1 2 -φ1.3 (2.1) (1.19) 7.62 5 7.62 3.2 3.2 7.62 3.2 JS-MN-KT (1.19) JS-K (1.19) JS-M-K 3 -φ1.5 22.1 2 -φ1.3 (2.1) 2 -φ1.5 18.9 (2.1) 2 -φ1.3 ( ): Reference value Unit: mm * Tolerance of PC board mounting hole layout : ±0.1 unless otherwise specified. 6 JS Series GENERAL INFORMATION 1. ROHS Compliance • All relays produced by Fujitsu Components are compliant with RoHS directive 2011/65/EU including amendments. • Use of Cadmium in electrical contacts is exempted as per Annex III of the RoHS directive 2011/65/EU. • Please consider expiry date of exemption. Relays with Cadmium containing contacts are not to be used for new designs. All relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/downloads/MICRO/fcai/relays/lead-free-letter.pdf Characteristic data is not guaranteed values, but measured values of samples from production line. • 2. Recommended lead free solder condition • Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. • Recommended solder for assembly: Sn-3.0Ag-0.5Cu. Flow Solder Condition: Solder by Soldering Iron: Soldering Iron: 30-60W Temperature: maximum 350-360˚C Duration: maximum 3 sec. IRS (infrared reflow soldering) Peak temperature: Max.250° C 250 Temperature (° C) Pre-Heating: maximum 120˚C within 90 sec. Soldering: dip within 5 sec. at 255˚C ± 5˚C solder bath Relay must be cooled by air immediately after soldering Recommended reflow soldering profile 220 170 Air cooling Pre-heating 130 90 to 120 sec. 20 to 30 sec. Max.120 sec. (Time) IMPORTANT NOTES FOR REFLOW SOLDERING • Temperature shall be measured at PC board upper surface. • Temperature at PC board upper surface may be changed depending on size of PC board, components • • mounted on the PC board and/or heating method. Please perform the confirmation test with your actual PC boards. This reflow solder condition is applicable only for reflow-capable relays. Do not reflow reflow-incapable relays. Recommended solder for assembly: Sn-3.0 Ag-0.5 Cu. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity • Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers • Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 7 JS Series Fujitsu Components International Headquarter Offices Japan FUJITSU COMPONENT LIMITED Shinagawa Seaside Park Tower 19F, 12-4, Higashi-shinagawa 4-chome, Shinagawa-ku, Tokyo,140-0002, Japan Tel: (81-3) 3450-1682 Fax: (81-3) 3474-2385 Email: fcl-contact@cs.jp.fujitsu.com Web: www.fujitsu.com/jp/fcl/ Asia Pacific FUJITSU COMPONENTS ASIA, LTD. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components North and South America FUJITSU COMPONENTS AMERICA, INC 2290 North First Street, Suite 212 San Jose, CA 95131, USA Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: us.fujitsu.com/components China FUJITSU ELECTRONIC COMPONENTS (SHANGHAI) CO., LTD. Unit 4306, InterContinental Center 100 Yu Tong Road, Shanghai 200070, China Tel: (86-21) 3253 0998 Fax: (86-21) 3253 0997 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components Europe FUJITSU COMPONENTS EUROPE B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: www.fujitsu.com/uk/components Hong Kong FUJITSU COMPONENTS HONG KONG CO., LTD Unit 506, Inter-Continental Plaza No.94 Granville Road, Tsim Sha Tsui, Kowloon, Hong Kong Tel: (852) 2881-8495 Tex: (852) 2894-9512 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components/ Korea FUJITSU COMPONENTS KOREA LIMITED Alpha Tower #403, 645 Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, 13524 Korea Tel: (82) 31-708-7108 Fax: (82) 31-709-7108 Email: fcal@sg.fujitsu.com www.fujitsu.com/sg/products/devices/components/ ©2017 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. October 31, 2018 8