MB39A214APFT-G-JNERE1

FUJITSU SEMICONDUCTOR DATA SHEET DS405-00007-1v0-E ASSP for Power Management Applications 2ch DC/DC converter IC with PFM/ PWM synchronous rectification MB39A214A „ DESCRIPTION MB39A214A is a N-ch/ N-ch synchronous rectification type 2ch Buck DC/DC converter IC equipped with a bottom detection comparator for low output voltage ripple. It supports low on-duty operation to allow stable output of low voltages when there is a large difference between input and output voltages. It also allows the high switching frequency setting, enabling the downsized peripheral circuits and low-cost configuration. MB39A214A realizes ultra-rapid response and high efficiency with built-in enhanced protection features. It is most suitable for the power supply for ASIC or FPGA core, input/output devices, or memory. „ FEATURES y y y y y y y y y y y y y y y y y y High efficiency Frequency setting by internal preset function : 310 kHz, 620 kHz, 1 MHz High accuracy reference voltage : ± 0.7% (Ta = + 25 °C) VIN Input voltage range : 6 V to 28 V Output voltage setting range : 0.7 V to 5.3 V Possible to select the automatic PFM/PWM selection mode or PWM-fixed mode PAF frequency limitation function (Prohibit Audio Frequency) : > 30 kHz (Min) Built-in boost diode, external fly-back diode not required Built-in discharge FET Built-in over voltage protection function Built-in under voltage protection function Built-in over temperature protection function Built-in over current limitation function Soft-start circuit without load dependence Current sense resistor not required Built-in synchronous rectification type output steps for N-ch MOS FET Standby current : 0 µA (Typ) Package : TSSOP24 (4.4 mm°6.5 mm°1.2 mm [Max]) „ APPLICATIONS y y y y y Digital TV Photocopiers STB BD, DVD players/recorders Projectors etc. Copyright©2011 FUJITSU SEMICONDUCTOR LIMITED All rights reserved 2011.12 FUJITSU SEMICONDUCTOR CONFIDENTIAL MB39A214A „ PIN ASSIGNMENT (TOP VIEW) BST1 1 24 DRVH1 EN1 2 23 LX1 VOUT1 3 22 DRVL1 FB1 4 21 PGND CS1 5 20 ILIM1 GND 6 19 VCC FREQ 7 18 VB CS2 8 17 MODE FB2 9 16 ILIM2 VOUT2 10 15 DRVL2 EN2 11 14 LX2 BST2 12 13 DRVH2 (FPT-24P-M09) 2 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A „ PIN DESCRIPTIONS Pin No. Pin Name I/O Description 1 BST1 — 2 EN1 I CH1 enable pin. 3 VOUT1 I CH1 input pin for DC/DC output voltage. 4 FB1 I CH1 input pin for feedback voltage. 5 CS1 I CH1 soft-start time setting capacitor connection pin. 6 GND — CH1 boost capacitor connection pin. Ground pin. 7 FREQ I Frequency switching signal input pin. FREQ : GND Short Switching frequency FREQ : Open Switching frequency FREQ : VB Short Switching frequency 8 CS2 I CH2 soft-start time setting capacitor connection pin. 9 FB2 I CH2 input pin for feedback voltage. 10 VOUT2 I CH2 input pin for DC/DC output voltage. 11 EN2 I CH2 enable pin. 12 BST2 — CH2 boost capacitor connection pin. 13 DRVH2 O CH2 output pin for external high-side FET gate drive. 14 LX2 — CH2 inductor and external high-side FET source connection pin. 15 DRVL2 — CH2 output pin for external low-side FET gate drive. 16 ILIM2 I CH2 over current detection level setting voltage input pin. 310 kHz 620 kHz 1 MHz 17 MODE I DC/DC control mode switching signal input pin. MODE : GND Short PFM/PWM MODE : Open PFM/PWM, PAF MODE : VB Short PWM fixed 18 VB O Internal circuit bias output pin. 19 VCC I Power input pin for control and output circuits. 20 ILIM1 I CH1 over current detection level setting voltage input pin. 21 PGND — Ground pin for output circuit. 22 DRVL1 O CH1 output pin for external low-side FET gate drive. 23 LX1 — CH1 inductor and external high-side FET source connection pin. 24 DRVH1 O CH1 output pin for external high-side FET gate drive. DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL 3 MB39A214A „ BLOCK DIAGRAM VIN (6 V to 28 V VCC EN1 EN2 VOUT1 VOUT1 VB VB 5.2 V VCC /EN1 OTP UVP VB 25 Ω tON Generator 1 µA FB1 BST1 VOUT1 R DRVH1 DRVH Q S CS1 VB 5 µA /EN1 /UVLO(OTP) REF1 (0.7 V) DRVL1 DRVL ILIM1 LX1 DRV Logic Slope & Offset ×1.0 4:1 LX1 ×1.0 PGND OVP1 OVP latch PGND OVP (delay:15 µs) REF1 × 1.15V OVP2 UVP1 REF1 × 0.7 V EN1 EN Logic UVP2 2 µA UVP latch UVP FREQ FREQ Select (delay:150 µs) 450 kΩ EN1 "H": Enable 2 µA UVLO (VB) VREF (0.7 V) REF1 REF2 2.5 V EN2 UVLO (VREF) OTP UVLO "H": UVLO Thermal release Protection 450 kΩ to CH2 VOUT2 MODE MODE Select BST2 VOUT2 VOUT2 DRVH2 LX2 FB2 DRVL2 CS2 ILIM2 EN2 GND 4 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A „ ABSOLUTE MAXIMUM RATINGS Parameter Symbol Condition Rating Min Max Unit VCC pin input voltage VVCC VCC pin − 0.3 + 30 V BST pin input voltage VBST BST1, BST2 pins − 0.3 + 36 V LX pin input voltage VLX LX1, LX2 pins −1 + 30 V — − 0.3 +7 V VEN EN1, EN2 pins − 0.3 + 30 V VFB FB1, FB2 pins − 0.3 VB + 0.3 V VVOUT VOUT1, VOUT2 pins − 0.3 +7 V VILIM ILIM1, ILIM2 pins − 0.3 VB + 0.3 V CS1, CS2 pins − 0.3 VB + 0.3 V VFREQ FREQ pin − 0.3 VB + 0.3 V VMODE MODE pin − 0.3 VB + 0.3 V DRVH1, DRVH2 pins, DRVL1, DRVL2 pins — 60 mA Ta ≤ + 25°C — + 1282 mW − 55 + 125 °C Voltage between BST and LX EN pin input voltage Input voltage Output current Power dissipation Storage temperature VBST-LX VCS IOUT PD TSTG — WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings. DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL 5 MB39A214A „ RECOMMENDED OPERATING CONDITIONS Parameter Symbol Condition Value Min Typ Max Unit VCC pin input voltage VVCC VCC pin 6 — 28 V BST pin input voltage VBST BST1, BST2 pins — — 34 V EN pin input voltage VEN EN1, EN2 pins 0 — 28 V VFB FB1, FB2 pins 0 — VB V VVOUT VOUT1, VOUT2 pins 0 — 5.5 V VILIM ILIM1, ILIM2 pins 0 — 2 V VFREQ FREQ pin 0 — VB V VMODE MODE pin 0 — VB V Input voltage Peak output current IOUT DRVH1, DRVH2 pins, DRVL1, DRVL2 pins Duty ≤ 5% (t = 1/fOSC¯Duty) − 1200 — + 1200 mA Operating ambient temperature Ta — − 30 + 25 + 85 °C WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device's electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their representatives beforehand. 6 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A „ ELECTRICAL CHARACTERISTICS Symbol Pin No. Output voltage VVB 18 VB = 0 A Input stability LINE 18 Load stability LOAD Short-circuit output current Parameter Bias Voltage Block [VB Reg.] 5.04 5.20 5.36 V VCC = 6 V to 28 V — 10 100 mV 18 VB = 0 A to − 1 mA — 10 100 mV IOS 18 VB = 0 V − 145 − 100 − 75 mA VTLH 18 VB pin 4.0 4.3 4.6 V VTHL 18 VB pin 3.7 4.0 4.3 V VH 18 VB pin — 0.3* — V Charge current ICS 5,8 CS1, CS2 = 0 V − 1.5 −1.0 − 0.75 µA Electrical discharge resistance RD 3,10 EN1, EN2 = 0 V, VOUT1, VOUT2 ≥ 0.15 V — 25* — Ω VVOVTH 3,10 EN1, EN2 = 0 V, VOUT1, VOUT2 pins — 0.2* — V tON11 24 FREQ pin GND connection VCC = 12 V, VOUT1 = 1.5 V 430 538 646 ns tON21 13 FREQ pin GND connection VCC = 12 V, VOUT2 = 1.5V 320 400 480 ns tON12 24 FREQ pin OPEN VCC = 12 V, VOUT1 = 1.5 V 210 263 316 ns tON22 13 FREQ pin OPEN VCC = 12 V, VOUT2 = 1.5 V 160 200 240 ns tON13 24 FREQ pin VB connection VCC = 12 V, VOUT1 = 1.5 V 130 163 196 ns tON23 13 FREQ pin VB connection VCC = 12 V, VOUT2 = 1.5 V 100 125 150 ns tONMIN11 24 FREQ pin GND connection VCC = 12 V, VOUT1 = 0V — 136 191 ns tONMIN21 13 FREQ pin GND connection VCC = 12 V, VOUT2 = 0V — 103 145 ns tONMIN12 24 FREQ pin OPEN VCC = 12 V, VOUT1 = 0V — 77 108 ns tONMIN22 13 FREQ pin OPEN VCC = 12 V, VOUT2 = 0V — 58 82 ns Under Threshold voltage voltage Lockout Protection Circuit Block Hysteresis width [UVLO] Soft-Start/ Discharge Block [Soft Start, Discharge] Discharge end voltage ON time (Preset value 1) ON time (Preset value 2) ON/OFF Time Generator Block [tON Generator] (Ta = +25°C, VCC = 12 V, EN1, EN2 = 5 V) Value Condition Unit Min Typ Max ON time (Preset value 3) Minimum ON time (Preset value 1) Minimum ON time (Preset value 2) Minimum ON time (Preset value 3) tONMIN13 24 FREQ pin VB connection VCC = 12V, VOUT1 = 0V — 55 77 ns tONMIN23 13 FREQ pin VB connection VCC = 12 V, VOUT2 = 0V — 43 61 ns Minimum OFF time tOFFMIN 24, 13 — 410 535 ns DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL — 7 MB39A214A Symbol Pin No. Threshold voltage VTH 4, 9 FB pin input current IFB VOUT pin input current IVO Parameter Error Comparison Block [Error Comp.] Over Current Detection Block [ILIM Comp.] Overvoltage Protection Circuit Block [OVP Comp.] Undervoltage Protection Circuit Block [UVP Comp.] Overtemperature Protection Circuit Block [OTP] Condition Value Unit Min Typ Max Ta = +25°C 0.695 0.700 0.705 V 4, 9 FB1, FB2 = 0.7 V − 0.1 0 +0.1 µA 3,10 VOUT1, VOUT2 = 1.5 V — 6.0 8.6 µA Over current detection VOFFILIM offset voltage 21 to 23 PGND − LX1, LX2 21 to 14 ILIM1, ILIM2 = 500 mV − 30 0 +30 mV ILIM pin current IILIM 20,16 ILIM1, ILIM2 = 0 V −6 −5 −4 µA ILIM pin current Temperature slope TILIM 20,16 Ta = +25°C — 4500* — ppm/ °C Over-voltage detecting voltage VOVP 4, 9 For REF1, REF2 voltage 110 115 120 % Hysteresis width VHOVP 4, 9 — — 5* — % Detection delay time tOVP — — 10 15 20 µs Under-voltage detecting voltage VUVP 4, 9 65 70 75 % Hysteresis width VHUVP 4, 9 — — 10* — % tUVP — — 100 150 200 µs TOTPH — — — 150* — °C TOTPL — — — 125* — °C High-side output on-resistance ROH 24,13 DRVH1, DRVH2 = − 100 mA — 4 6 Ω ROL 24,13 DRVH1, DRVH2 = 100 mA — 1 1.5 Ω Low-side output on-resistance ROH 22,15 DRVL1, DRVL2 = − 100 mA — 4 6 Ω ROL 22,15 DRVL1, DRVL2 = 100 mA — 1 1.5 Ω ISOURCE 24,13 22,15 LX1, LX2 = 0 V, BST1, BST2 = VB DRVH1, DRVH2 = 2.5 V Duty ≤ 5% — − 0.5* — A ISINK 24,13 22,15 LX1, LX2 = 0 V, BST1, BST2 = VB DRVH1, DRVH2 = 2.5 V Duty ≤ 5% — 0.9* — A 15 25 35 ns 35 50 65 ns Detection delay time Protection temperature Output source current Output Block [DRV] Output sink current Dead time tD For REF1, REF2 voltage LX1, LX2 = 0 V, BST1, BST2 = VB DRVL1, DRVL2-low to 24 to 22 DRVH1, DRVH2-on 13 to 15 LX1, LX2 = 0 V, BST1, BST2 = VB DRVH1, DRVH2-low to DRVL1, DRVL2-on 8 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A Parameter Output Block [DRV] Switching Frequency Control Block [FREQ] PFM Control Circuit Block [MODE] Condition Value Unit Min Typ Max 0.75 0.85 0.95 V LX1, LX2 = 0 V, BST1, BST2 = 5.2 V 11 15 22 µA VF 1,12 IF = 10 mA Bias current IBST 1,12 Preset value 1 conditions VFREQ1 7 FREQ pin: GND connection 0 — 0.2 V Preset value 2 conditions VFREQ2 7 FREQ pin: OPEN 0.6 — 1.2 V Preset value 3 conditions VFREQ3 7 FREQ pin: VB connection 2.4 — VB V FREQ pin output voltage VFREQ 7 FREQ = OPEN 0.63 0.9 1.17 V PFM/PWM mode conditions PAF function negate VPFM1 17 MODE pin: GND connection 0 — 0.2 V PFM/PWM mode conditions PAF function assert VPFM2 17 MODE pin : OPEN 0.6 — 1.2 V PWM-fixed mode conditions VPWM 17 MODE pin : VB connection 4.6 — VB V fPAF — Ta = − 30°C to +85°C 30 45 — kHz VMODE 17 MODE = OPEN 0.63 0.9 1.17 V MODE pin voltage Power Supply Current Pin No. BST diode voltage PAF frequency Enable Block [EN1 , EN2] Symbol ON condition VON 2, 11 EN1, EN2 pins 2.64 — — V OFF condition VOFF 2, 11 EN1, EN2 pins — — 0.66 V Hysteresis width VH 2, 11 EN1, EN2 pins — 0.4* — V Input current IEN 2, 11 EN1, EN2 = 5V 11 15 22 µA Standby current ICCS Power supply current during idle period Power supply current during operation ICC1 ICC2 19 EN1, EN2 = 0V — 0 10 µA 19 LX1, LX2 = 0 V BST1, BST2 : VB connection FB1, FB2 = 0.75 V — 600 860 µA 19 LX1, LX2 = 0V BST1, BST2 : VB connection FB1, FB2 = 0.6 V — 1200 1700 µA *: This parameter is not be specified. This should be used as a reference to support designing the circuits. DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL 9 MB39A214A „ TYPICAL CHARACTERISTICS Power dissipation vs. Operating ambient temperature Power dissipation PD (mW) 2000 1500 1282 1000 500 0 -50 -25 +0 +25 +50 +75 +100+125 Operating ambient temperature Ta (°C) VB bias voltage vs. Operating ambient temperature VB bias voltage vs. VB bias output current 5.4 5.40 5.36 Ta = +25 °C 5.28 5.24 5.20 5.16 5.12 VCC=12V IVB=0A 5.08 VB bias voltage VVB (V) VB bias voltage VVB (V) 5.32 5.3 5.2 VCC=12V 5.1 VCC=28V 5.04 VCC=6V 5.00 5.0 0 +20 +40 +60 +80 +100 -30 -25 -20 -15 -10 -5 0 Operating ambient temperature Ta (°C) VB bias output current IVB (mA) Error Comp. Threshold voltage vs. Operating ambient temperature ILIM pin current vs. Operating ambient temperature -3.5 0.705 0.704 0.703 -4.0 0.702 0.701 0.700 0.699 0.698 ILIM pin current IILIM (µA) Error Comp. Threshold voltage VTH (V) -40 -20 0.697 0.696 0.695 -40 -20 0 +20 +40 +60 +80+100 Operating ambient temperature Ta (°C) 10 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL -4.5 -5.0 -5.5 -6.0 -40 -20 0 +20 +40 +60 +80 +100 Operating ambient temperature Ta (°C) DS405-00007-1v0-E MB39A214A DRVH2 on time vs. Operating ambient temperature 500 450 350 250 FREQ=OPEN 200 150 100 FREQ=VB 50 -40 -20 0 +20 +40 +60 +80 +100 Operating ambient temperature Ta (°C) DRVH1 minimum on time vs. Input voltage DRVH2 minimum on time vs. Input voltage 200 Ta = + 25°C 200 FREQ=GND 150 FREQ=OPEN 100 50 FREQ=VB 0 DRVH2 minimum on time tONMIN1 (ns) 250 DRVH1 minimum on time tONMIN1 (ns) VCC=12V VOUT2=1.5V 300 Operating ambient temperature Ta (°C) Ta = + 25°C 150 FREQ=GND 100 FREQ=OPEN 50 FREQ=VB 0 5 10 15 20 25 30 5 20 25 DRVH1 minimum on time vs. Operating ambient temperature DRVH2 minimum on time vs. Operating ambient temperature 30 FREQ=GND VCC=12V VOUT1= 0 V FREQ=OPEN 80 60 FREQ=VB 40 -40 -20 0 +20 +40 +60 +80 +100 Operating ambient temperature Ta (°C) DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DRVH2 minimum on time tONMIN2 (ns) 140 120 100 15 Input voltage VIN (V) 160 140 10 Input voltage VIN (V) 180 DRVH1 minimum on time tONMIN1 (ns) FREQ=GND 400 DRVH2 on time tON2 (ns) DRVH1 on time tON1 (ns) DRVH1 on time vs. Operating ambient temperature 700 650 600 FREQ=GND 550 500 VCC=12V 450 VOUT1=1.5V 400 350 FREQ=OPEN 300 250 200 150 FREQ=VB 100 -40 -20 0 +20 +40 +60 +80 +100 120 FREQ=GND 100 VCC=12V VOUT2=0 V 80 FREQ=OPEN 60 40 FREQ=VB 20 -40 -20 0 +20 +40 +60 +80 +100 Operating ambient temperature Ta (°C) 11 MB39A214A Minimum off time vs. Operating ambient temperature Minimum off time vs. Input voltage 600 600 550 Ta = + 25°C 500 Minimum off time tOFFMIN (ns) Minimum off time tOFFMIN (ns) 550 450 400 350 300 250 200 5 10 15 20 25 400 350 300 250 0 +20 +40 +60 +80 +100 Input voltage VIN (V) Operating ambient temperature Ta (°C) Dead time vs. Operating ambient temperature Bootstrap diode IF vs. VF 100 tD2 10 45 40 LX=0V VBST=VB 35 30 20 -40 -20 0 Ta =+ 85°C 1 Ta = - 30°C 0.1 Ta =+25°C 0.01 tD1 25 IF current IF (mA) Dead time (ns) 50 450 200 -40 -20 30 60 55 VCC=12V 500 +20 +40 +60 +80 +100 Operating ambient temperature Ta (°C) 0.001 0.2 0.4 0.6 0.8 1 1.2 VF voltage VF (V) tD1 : Period from DRVL off to DRVH on tD2 : Period from DRVH off to DRVL on 12 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A „ FUNCTION Bottom detection comparator system for low output voltage ripple The bottom detection comparator system for low output voltage ripple determines the ON time (tON) using the input voltage (VIN) and output voltage (VOUT) to hold the ON state to a specified period. During the OFF period, the reference voltage (INTREF) is compared with the feedback voltage (FB) using the error comparator (Error Comp.). When the feedback voltage (FB) is below the reference voltage (INTREF) , RS-FF is set and the ON period starts again. Switching is repeated as described above. Error Comp. is used to compare the reference voltage (INTREF) with the feedback voltage (FB) to control the off-duty condition in order to stabilize the output voltage. This system adds the inductor current slope detected during the synchronous rectification period (tOFF) to the reference voltage (INTREF) , and generates an output voltage slope during the OFF period, which is essential for the bottom detection comparator system, in the IC. This enables the stable control operations under the low output voltage ripple conditions. y Circuit diagram VOUT VIN Bias Reg. VIN tON generator tON FB INTREF + Hi-side Drive RS-FF R Q RS out DRVH Drive Logic S IL VOUT Bias Lo-side Drive + - DRVL Slope Detector VREF y Waveforms tON DRVH tOFF IL FB INTREF t DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL 13 MB39A214A (1) Bias Voltage Block (VB Reg.) The 5.2 V (Typ) bias voltage is generated from the VCC pin voltage for the control, output, and boost circuits. When either or both of the EN1 pin (pin 2) and EN2 pin (pin 11) are set to the “H” level, the system is restored from the standby state to supply the bias voltage from the VB pin (pin 18). (2) ON/OFF Time Generator Block (tON Generator) This block contains a capacitor for timing setting and a resistor for timing setting and generates ON time (tON) which depends on input voltage and output voltage. The switching frequency can be switched by setting the FREQ pin (pin 7) to any one of GND connection, OPEN, and VB connection. ON time for each CH is obtained from the following formula. tON1 (ns) = VVOUT1 ¯ 4300 (fOSC1 VVIN 230 kHz) tON2 (ns) = VVOUT2 ¯ 3200 (fOSC2 VVIN 310 kHz) tON1 (ns) = VVOUT1 ¯ 2100 (fOSC1 VVIN 460 kHz) tON2 (ns) = VVOUT2 ¯ 1600 (fOSC2 VVIN 620 kHz) tON1 (ns) = VVOUT1 ¯ 1300 (fOSC1 VVIN 750 kHz) tON2 (ns) = VVOUT2 ¯ 1000 (fOSC2 VVIN 1000 kHz) The switching frequency of CH2 is set to 1.33 times that of CH1 to prevent the beat by the frequency difference of channel to channel. (3) Output Block (DRV1, DRV2) The output circuit is configured in CMOS type for both of the high-side and the low-side. It provides the 0.5 A (Typ) source current and 0.9 A (Typ) sink current, drive the external N-ch MOS FET. The output circuit of the high-side FET supplies the power from the boost circuit including the built-in boost diode. The output circuit of the low-side FET supplies the power from the VB pin. This circuit monitors the gate voltages of the high-side and low-side FETs. Until either FET is turned off, this circuit controls the ON timing of another FET, preventing the shoot-through current. The sink ON resistance of the output circuit is low 1 Ω (Typ), improve the self turn on margin of low-side FET. 14 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A (4) Starting sequence When the EN1 pin (pin 2) or EN2 pin (pin 11) is set to the “H” level, the bias voltage is supplied from the VB pin. If the voltage of the VB pin exceeds the UVLO threshold voltage, the DC/DC converter starts operations and carries out the soft start. The soft start is a function used to prevent a rush current when the power is started. Activating the soft start initiates charging of the capacitor connected to the CS1 pin (pin 5) and CS2 pin (pin 8) and inputs the lamp voltage to the error comparator (Error Comp.) of each channel. The DC/DC converter generates the output voltage according to that lamp voltage. This results in the soft start operation that does not depend on the output load. The over voltage protection (OVP) and under voltage protection (UVP) functions are disabled while the soft start is active. EN1 VB CS1 UVLO release UVLO VTLH CH1 soft start completed INTREF 0.805 V 1.6 V DRVH1 DRVL1 VOUT1 EN2 CS2 CH2 soft start completed INTREF 1.6 V 0.805 V DRVH2 DRVL2 VOUT2 DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL 15 MB39A214A (5) DC/DC converter stop sequence (Discharge, standby) When the EN1 pin (pin 2) or EN2 pin (pin 11) is set to the “L” level, the output capacitor is discharged using the discharge FET (RON 25 Ω) in the IC. If the voltage of the VOUT1 pin (pin 3) and VOUT2 pin (pin 10) is below 0.2 V (Typ) by discharging the output capacitor, the IC stops discharge operation. Further, if both the EN1 and EN2 pins are set to the “L” level, the IC also stops the output of the VB pin and enters the standby state after detecting UVLO. The current of the VCC pin (IVCC) is then 10 µA (Max). Standby EN1 VB UVLO VTHL 1.6 V CS1 DRVH1 DRVL1 VOUT1 CH1 discharge FET ON 0.2 V EN2 CS2 1.6 V DRVH2 DRVL2 VOUT2 CH2 discharge FET ON 0.2 V (6) Under Voltage Lockout Protection (UVLO) The under voltage lockout protection (UVLO) protects ICs from malfunction and protects the system from destruction/deterioration, according to the reasons mentioned below. y Transitional state when the bias voltage (VB) or the reference voltage (VREF) starts. y Momentary decrease To prevent such a malfunction, this function detects a voltage drop of the VB pin (pin 18) using the comparator (UVLO Comp.), and stops IC operations. When the VB pin exceeds the threshold voltage of the under voltage lockout protection circuit, the system is restored. 16 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A (7) Over Current Limitation (ILIM) This function limits the output current when it has increased, and protects devices connected to the output. This function detects the inductor current IL from the electromotive force of the low-side FET on-resistance RON, and compares this voltage with the 1/5-time value of the voltage VILIM of the ILIM1 pin (pin 20) and ILIM2 pin (pin 16) on a cyclically, using ILIM Comp. Until this voltage falls below the over current limit value, the high-side FET is held in the off state. After the voltage has fallen below the limit value, the high-side FET is placed into the on state. This limits the lower bound of the inductor current and also restricts the over current. As a result, it becomes operation that the output voltage droops. The over current limit value is set by connecting the resistor to the ILIM pin. The ILIM pin supplies the constant current of 5 µA (Typ) . However, the current value has a temperature slope up to 4500 ppm/°C to compensate the temperature dependence characteristics of the low-side FET on-resistance. ILIM detection value (RON × IL = IL (IOUT1 ) VILIM 5 ) Keep the off state of the high-side FET until the detection value is gained. Output voltage setting value VOUT DRVH DRVL Normal operation DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL Over current limit operation 17 MB39A214A (8) Over Voltage Protection (OVP) This function stops the output voltage when the output voltage has increased, and protects devices connected to the output. 1. Using OVP Comp, this function makes a comparison between the voltage which is 1.15 times (Typ) of the internal reference voltage INTREF1 and INTREF2 (0.7 V), and the feedback voltage for the FB1 pin (pin 4) and the FB2 pin (pin 9). 2. If the feedback voltage mentioned in 1 detects the higher state by 15µs (Typ) or more, the operations below will be performed. y Set the RS latch. y Set the DRVH1 pin (pin 24) and the DRVH2 pin (pin 13) to the “L” level. y Set the DRVL1 pin (pin 22) and the DRVL2 pin (pin 15) to the “H” level. These operations fix the high-side FET to the off state and the low-side FET to the on state for both channels of the DC/DC converter, and stops switching (latch stop).The over-voltage protection state can be cancelled by setting both the EN1pin (pin 2) and EN2 pin (pin 11) to the “L” level or reducing the VCC power once until the bias voltage (VB) falls below VTHL of UVLO. VOUT1 Output voltage setting value 0V INTREF¯1.15 INTREF¯1.10 FB1 INTREF 0V DRVH1 DRVL1 CS1 Output voltage setting value VOUT2 0V INTREF FB2 0V DRVH2 DRVL2 CS2 EN1, EN2 Standby UVLO VTHL VB Less than 15 µs 15 µs Cancellation of over-voltage protection state by EN = "L". 18 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A (9) Under Voltage Protection (UVP) This function stops the output voltage when the output voltage has lowered, and protects devices connected to the output. 1. Using UVP Comp, this function makes a comparison between the voltage which is 0.7 times (Typ) of the internal reference voltage REF1, REF2 (0.7 V), and the feedback voltage for the FB1 pin (pin 4) and the FB2 pin (pin 9). 2. If the feedback voltage mentioned in 1 detects the higher state by 150µs (Typ) or more, the operations below will be performed. y Set the RS latch. y Set the DRVH1 pin (pin 24) and the DRVH2 pin (pin 13) to the “L” level. y Set the DRVL1 pin (pin 22) and the DRVL2 pin (pin 15) to the “L” level. These operations fix the high-side FET to the off state and the low-side FET to the off state for both channels of the DC/DC converter, and stops switching (latch stop). The discharge operation is then carried out to discharge the output capacitor (The discharge operation continues until the state of the under-voltage protection is released). The under-voltage protection state can be cancelled by setting both the EN1 pin (pin 2) and EN2 pin (pin 11) to the “L” level or reducing the VCC power once until the bias voltage (VB) falls below VTHL of UVLO. Output voltage setting value VOUT1 0V INTREF INTREF ¯ 0.8 INTREF ¯0.7 0V FB1 DRVH1 DRVL1 CS1 Output voltage setting value VOUT2 0V INTREF FB2 0V DRVH2 DRVL2 CS2 EN1, EN2 Standby UVLO VTHL VB Less than 15 µs 150 µs DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL Cancellation of over-voltage protection state by EN = "L". 19 MB39A214A (10) Over Temperature Protection (OTP) The over-temperature protection circuit block (OTP) provides a function that prevents the IC from a thermal destruction. If the junction temperature reaches + 150°C, the DRVH1 pin (pin 24) and DRVH2 pin (pin 13) are set to the “L” level, and the DRVL1 pin (pin 22 ) and DRVL2 pin (pin 15) are set to the “L” level. This fixes the high-side and low-side FETs to the off-state, of both channels in the DC/DC converter, causing switching to be stopped. The discharge operation is then carried out to discharge the output capacitor (The discharge operation continues until the state of the over-temperature protection is released). If the junction temperature drops to + 125°C, the soft start is reactivated. (Restored automatically.) (11) Operation mode In the PWM-fixed mode, the system acts by the switching frequency specified with the FREQ pin regardless of the load. In the automatic PFM/PWM selection mode, the switching frequency is reduced at low load, for enhancing the conversion efficiency characteristics. This function detects 0 A of the inductor current from the electromotive force of the low-side FET ON resistance when the low-side FET ON state, and places the low-side FET into the off state. This idle period continued until the output voltage decreased, this results the switching frequency being reduced automatically depending on the load current when the inductor current is below the critical current. The system acts by the switching frequency specified with the FREQ pin, when the inductor current exceeds the critical current. For Automatic PFM/PWM selection mode with PAF function, the switching frequency at low load is held to 30 kHz (Min) or more. The operation mode can be switched by setting the MODE pin (pin 17) to any one of GND connection, OPEN, and VB connection. y PWM-fixed mode IOUTx ILXx 0A VLXx Inductor current in the opposite direction y Automatic PFM/PWM selection mode IOUTx ILXx 0A VLXx Switching frequency reduced X : Each channel number 20 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A y Enable function table EN1 pin EN2 pin DC/DC converter (CH1) DC/DC converter (CH2) L L OFF OFF H L ON OFF L H OFF ON H H ON ON y DC/DC Control mode function table MODE pin DC/DC control GND connection Automatic PFM/PWM selection mode OPEN Automatic PFM/PWM selection mode with PAF function VB connection PWM-fixed mode y Switching frequency control function table FREQ pin Switching frequency GND connection fOSC1 230 kHz, fOSC2 310 kHz OPEN fOSC1 460 kHz, fOSC2 620 kHz VB connection fOSC1 750 kHz, fOSC2 1000 kHz y Protection function table The following table shows the state of the VB pin (pin 18), the DRVH1 pin (pin 24), the DRVH2 pin (pin 13), the DRVL1 pin (pin 22), the DRVL2 pin (pin 15) when each protection function operates. Protection function Under Voltage Lockout Protection (UVLO) Detection condition Output of each pin after detection VB DRVH1, DRVL1, DRVH2 DRVL2 — Over-current limitation (ILIM) VPGND - VLX1, VLX2 > VILIM1, VILIM2 5.2 V Over Voltage Protection (OVP) VFB1, VFB2 > INTREF1, INTREF2¯1.15 (15 µs or higher) 5.2 V L H 0 V clamping Under Voltage Protection (UVP) VFB1, VFB2 > INTREF1, INTREF2¯0.7 (150 µs or higher) 5.2 V L L Electrical discharge by discharge function Tj > + 150 °C 5.2 V L L Electrical discharge by discharge function EN1, EN2: H → L (VOUT1, VOUT2 > 0.2 V) 5.2 V L L Electrical discharge by discharge function Enable (EN) DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL L Natural electric discharge VB < 4.0 V Over Temperature Protection (OTP) L DC/DC output dropping operation Switching Switching The voltage is dropped by the constant current 21 MB39A214A „ I/O PIN EQUIVALENT CIRCUIT DIAGRAM FB1, FB2 pins EN1, EN2 pins VB VCC ESD protection element EN1 EN2 FB1 FB2 ESD protection element GND GND FREQ pin MODE pin VB VB FRWQ MODE GND GND ILIM1, ILIM2 pins VB ILIM1 ILIM2 GND 22 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL VOUT1, VOUT2 pins VB VOUT1 VOUT2 PGND GND DS405-00007-1v0-E MB39A214A CS pin DRVL1, DRVL2 pins VB VB DRVL1 DRVL2 CS1 CS2 GND PGND DRVH1, DRVH2, BST1, BST2, LX1, LX2 pins VB pin VB VCC BST1 BST2 VB DRVH1 DRVH2 GND LX1 LX2 PGND VCC pin VCC GND PGND DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL 23 MB39A214A „ EXAMPLE APPLICATION CIRCUIT VIN VCC VIN PGND R1-2 R1-1 C7 3 VOUT1 VB 18 C8 FB1 R2 4 12 V 19 R5 4 3 1.0 V, 7 A L1 VOUT1 LX1 23 DRVL1 22 Q1 7 8 2 C2-3 17 MODE PGND + C2-1 C12 20 ILIM1 Q1 5 6 C1-1 DRVH1 24 C1-2 EN1 5 CS1 C5 2 EN1 VIN BST1 1 1 7 FREQ MB39A214A R3-2 R3-1 10 VOUT2 VIN BST2 12 3 C3-2 C6 4 C3-1 Q3 5 6 R4 9 FB2 DRVH2 13 1.8 V, 7 A L2 VOUT2 LX2 14 ILIM2 R6 C13 16 DRVL2 15 PGND 6 2 + PGND C4-3 8 CS2 Q3 7 8 C4-1 11 EN2 EN2 1 21 GND 24 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A „ PART LIST Component Vendor Package Part number Remarks Q1 VDS = 30 V, ID = 9 A, 5.4 A, N-ch FET RON = 34 mΩ, 13 mΩ RENESAS SOP8 µPA2758 DualType (2elements) Q3 N-ch FET VDS = 30 V, ID = 9 A, 5.4 A, RON = 34 mΩ, 13 mΩ RENESAS SOP8 µPA2758 DualType (2elements) L1 Inductor 1 µH (18 A) NEC TOKIN - MPC1055L1R0 L2 Inductor 1.5 µH (12.4 A) NEC TOKIN - MPLC1040L1R5 C1-1 Ceramic capacitor 10 µF (25 V) MURATA 3216 GRM31CB31E106K C1-2 Ceramic capacitor 10 µF (25 V) MURATA 3216 GRM31CB31E106K C2-1 POSCAP 220 µF (2 V) SANYO D case 2TPLF220M6 C2-3 Ceramic capacitor 1000 pF (50 V) TDK 1608 C1608JB1H102K C3-1 Ceramic capacitor 10 µF (25 V) MURATA 3216 GRM31CB31E106K C3-2 Ceramic capacitor 10 µF (25 V) MURATA 3216 GRM31CB31E106K C4-1 POSCAP 150 µF (6.3 V) SANYO D case 6TPL150MU C4-3 Ceramic capacitor 1000 pF (50 V) TDK 1608 C1608JB1H102K C5 Ceramic capacitor 0.1 µF (50 V) TDK 1608 C1608JB1H104K C6 Ceramic capacitor 0.1 µF (50 V) TDK 1608 C1608JB1H104K C7 Ceramic capacitor 0.1 µF (50 V) TDK 1608 C1608JB1H104K C8 Ceramic capacitor 4.7 µF (16 V) TDK 1608 C1608JB1C475K C12 Ceramic capacitor 3300 pF (50 V) TDK 1608 C1608JB1H332K C13 Ceramic capacitor 3300 pF (50 V) TDK 1608 C1608JB1H332K R1-1 Resistor 1.6 kΩ SSM 1608 RR0816P162D R1-2 Resistor 27 kΩ SSM 1608 RR0816P273D R2 Resistor 68 kΩ SSM 1608 RR0816P683D R3-1 Resistor 0.047 kΩ SSM 1608 RR0816P470D R3-2 Resistor 56 kΩ SSM 1608 RR0816P563D R4 Resistor 36 kΩ SSM 1608 RR0816P363D R5 Resistor 110 kΩ SSM 1608 RR0816P114D SSM 1608 RR0816P124D R6 RENESAS SANYO NEC TOKIN TDK MURATA SSM Item Specification 120 kΩ Resistor : Renesas Electronics Corporation : SANYO Electric Co., Ltd : NEC TOKIN Corporation : TDK Corporation : Murata Manufacturing Co., Ltd. : SUSUMU Co.,Ltd. DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL 25 MB39A214A „ APPLICATION NOTE 1. Setting Operating Conditions Setting output voltages The output voltage can be set by adjusting the setting output voltage resistor ratio. Setting output voltage is calculated by the following formula. VOUTx = R1 + R2 R2 ¯ (0.6946 + 0.2667¯ΔIL¯ (1− ΔVOUTx = ESR ¯ΔIL, ΔIL = VOUTx VIN ΔVOUTX tOFF RON_Sync ΔIL ESR L fOSC VIN − VOUT L ¯ 2.8¯10-7 tOFF VOUT VIN ¯ fOSC , tOFF = ) ¯RON_Sync) + ΔVOUTx 2 (VIN − VOUTx) VIN¯fOSC : Output setting voltage [V] : Power supply voltage [V] : Output ripple voltage value [V] : Off time [s] : ON resistance of low-side FET [Ω] : Ripple current peak-to-peak value of inductor [A] : Series resistance element of output capacitor [Ω] : Inductor value [H] : Switching frequency [Hz] VOUTX VOUTx R1 FBX R2 x: Each channel number The total resistor value (R1+R2) of the setting output resistor should be selected up to 100 kΩ. 26 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A Minimum power supply voltage The maximum on duty is limited by "the minimum off time (tOFFMIN) that an IC holds without fail as a fixed value" and "the on time (tON) determined by the power voltage value and the output voltage setting value". The ratio between the output voltage and the power voltage must be less than the maximum on duty. The minimum power supply voltage that is required to sustain the output voltage can be calculated by the following formula. VIN_MIN = (VOUT + IOUT_MAX ¯ (RDC + RON_Main)) ¯ VOUT VOUT − (VOUT + IOUT_MAX ¯ (RDC + RON_Sync)) ¯ tOFF_MIN ¯ fOSC ¯1.2 VIN_MIN VOUT IOUT_MAX RON_Main RON_Sync RDC fOSC tOFF_MIN : Power supply voltage [V] : Output setting voltage [V] : Maximum load current value [A] : ON resistance of high-side FET [Ω] : ON resistance of low-side FET [Ω] : Series resistance of inductor [Ω] : Switching frequency setting value [Hz] : Minimum off time (Maximum value) [s] (For the minimum off time, see “ON/OFF Time [Minimum OFF time ] ” in “„ELECTRICAL CHARACTERISTICS”.) Use the smaller switching frequency setting in order to make the voltage output possible with the lower power voltage. Slope voltages It is necessary to sustain the Slope voltage 15 mV or higher in order to obtain the stable switching cycle. The Slope voltage can be calculated by the following formula. VSlope = (VIN − VOUT) ¯ VOUT ¯ RON_Sync L ¯ VIN ¯ fOSC VSlope VIN VOUT fOSC RON_Sync L : Slope voltage [V] : Power supply voltage [V] : Output setting voltage [V] : Switching frequency [Hz] : ON resistance of low-side FET [Ω] : Inductor value [H] DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL 27 MB39A214A Setting soft-start time Calculate the soft-start time by the following formula. ts = 7 ¯ 105 ¯ CCS ts CCS : Soft-start time [s] (time until output reaches 100%) : CS pin capacitor value [F] Calculate the delay time until the soft-start activation by the following formula. td = 43 ¯ CVB td : VB voltage delay time (at VIN = 12 V) [s] CVB : VB pin capacitor value [F] When activating the other in the state where a side channel has already been activated (UVLO release: VB output already), the delay time is hardly generated. ts1 ts2 EN1 EN2 VOUT1 VOUT2 td 28 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A Setting switching frequency The switching frequency is set at the FREQ pin. As for the setting process, see the switching frequency control function table. Setting over current limitation The over current limitation value can be set by adjusting the over current limitation setting resistor value connected to the ILIM pin. Calculate the resistor value by the following formula. RLIM = 106 ¯ RON_Sync ¯ (ILIM − RLIM ILIM ΔIL RON_Sync ΔIL 2 ) : Over current limitation value setting resistor [Ω] : Over current limitation value [A] : Ripple current peak-to-peak value of inductor [A] : ON resistance of low-side FET [Ω] ILIM RLIM Inductor current ΔIL ILIM Over current limitation value IOUT 0 Time If the rate of inductor saturation current is small, the inductor value decreases and the ripple current of inductor increase when the over-current flows. At that time there is a possibility that the limited output current increases or is not limited, because the bottom of inductor current is detected. It is necessary to use the inductor that has enough large rate of inductor saturation current to prevent the overlap current. DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL 29 MB39A214A The over current limit value is affected by ILIM pin source current and over current detection offset voltage in the IC except for the on resistance of the low-side FET and the inductor value. The variation of dropped over current limit value caused by IC characteristics is calculated by the following formula. ΔILIM = 2 ¯10-7¯ RLIM + 0.03 RON_Sync ΔILIM RLIM RON_Sync : The variation of dropped over current limit value [A] : Over current limitation value setting resistor [Ω] : ON resistance of low-side FET [Ω] Inductor current Over current limit value ILIM ΔILIM Dropped over current limit value due to ILIM’ IC's characteristics IO 0 Time The over current detection value needs to set a sufficient margin against the maximum load current. 30 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A Power dissipation and the thermal design IC's loss increases, if IC is used under the high power supply voltage, high switching frequency, high load and high temperature. The IC internal loss can be calculated by the following formula. PIC = VCC ¯ (ICC + QG_Total1 ¯ fOSC1 + QG_Total2 ¯ fOSC2) PIC VCC ICC QG_Total1 QG_Total2 fOSC1 fOSC2 : IC internal loss [W] : Power supply voltage (VIN) [V] : Power supply current [A] (2 mA Max) : Total quantity of charge for the high-side FET and the low-side FET of each CH1 [C] : Total quantity of charge for the high-side FET and the low-side FET of each CH2 [C] : CH1 switching frequency [Hz] : CH2 switching frequency [Hz] Calculate junction temperature (Tj) by the following formula. Tj = Ta + θja ¯ PIC Tj Ta θja PIC : Junction temperature [°C] (+ 125°C Max) : Ambient temperature [°C] : TSSOP-24P Package thermal resistance (+ 78°C /W) : IC internal loss [W] Handling of the pins when using a single channel Although this device is a 2-channel DC/DC converter control IC, it is also able to be used as a 1-channel DC/DC converter by handling the pins of the unused channel as shown in the following diagram. VOUTx FBx CSx ILIMx ENx LXx BSTx “Open” DRVHx “Open” DRVLx “Open” Note: x is the unused channel number. DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL 31 MB39A214A 2. Selecting parts Selection of smoothing inductor The inductor value selects the value that the ripple current peak-to-peak value of the inductor is 50% or less of the maximum load current as a rough standard. Calculate the inductor value in this case by the following formula. L≥ VIN −VOUT ¯ LOR¯ IOUT_MAX L IOUT_MAX LOR VIN VOUT fOSC VOUT VIN ¯fOSC : Inductor value [H] : Maximum load current [A] : Ripple current peak-to-peak value of inductor/Maximum load current ratio (= 0.5) : Power supply voltage [V] : Output setting voltage [V] : Switching frequency [Hz] It is necessary to calculate the maximum current value that flows to the inductor to judge whether the electric current that flows to the inductor is a rated value or less. Calculate the maximum current value of the inductor by the following formula. ILMAX ≥ IOUT_MAX + ΔIL 2 ILMAX : Maximum current value of inductor [A] IOUT_MAX : Maximum load current [A] : Ripple current peak-to-peak value of inductor [A] ΔIL L : Inductor value [H] VIN : Power supply voltage [V] VOUT : Output setting voltage [V] fOSC : Switching frequency [Hz] Inductor current ILMAX IOUT_MAX ΔIL Time 0 32 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A Selection of Switching FET If selecting the high-side FET so that the value of the high-side FET conduction loss and the high-side FET switching loss is same, the loss is effectively decreased. Confirm that the high-side FET loss is within the rating value. PMainFET = PRON_Main + PSW_Main PMainFET : High-side FET loss [W] PRON_Main : High-side FET conduction loss [W] PSW_Main : High-side FET switching loss [W] High-side FET conduction loss PRON_Main = IOUT_MAX2 ¯ PRON_Main IOUT_MAX VIN VOUT RON_Main VOUT ¯ RON_Main VIN : High-side FET conduction loss [W] : Maximum load current [A] : Power supply voltage [V] : Output voltage [V] : ON resistance of high-side FET [Ω] The high-side FET switching loss can be calculated roughly by the following formula. PSW_Main 1.56 ¯ VIN ¯ fOSC ¯ IOUT_MAX ¯ QSW PSW_Main VIN fOSC IOUT_MAX QSW : Switching loss [W] : Power supply voltage [V] : Switching frequency [Hz] : Maximum load current [A] : Amount of high-side FET gate switch electric charge [C] MOSFET has a tendency where the gate drive loss increases because the lower drive voltage product has the bigger amount of gate electric charge (QG). Normally, we recommend a 4 V drive product, however, the idle period at light load (both the high-side FET and the low-side FET is off-period) gets longer and the gate drive voltage of the high-side FET may decrease, in the automatic PFM/PWM selection mode. The voltage drops most at no-load mode. At this time, confirm that the boost voltage (voltage between BST-LX pins) is a big enough value for the gate threshold value voltage of the high-side FET. If it is not enough, consider adding the boost diode, increasing the capacitor value of the boost capacitor or using a 2.5 V (or 1.8 V) drive product to the high-side FET. Select the ON resistance of low-side FET from the range below. 0.2 RON_Sync ≤ (ILIM − RON_Sync ΔIL ILIM ΔIL 2 , RON_Sync ≤ ) 0.1 ΔIL , RON_Sync ≥ 0.015 ΔIL : ON resistance of low-side FET [Ω] : Ripple current peak-to-peak value of inductor [A] : Over current detection value [A] DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL 33 MB39A214A If the formula above has been already satisfied and then a low ON resistance FET as possible is used for the low-side FET, the loss is effectively decreased. Especially, it works dramatically in the low on duty mode. The loss of the low-side FET can be calculated by the following formula. PSyncFET = PRON_Sync = IOUT_MAX2 ¯ (1 – PSyncFET PRON_Sync IOUT_MAX VIN VOUT RON_Sync VOUT ) ¯ RON_Sync VIN : Low-side FET loss [W] : Low-side FET conduction loss [W] : Maximum load current [A] : Power supply voltage [V] : Output voltage [V] : ON resistance of low-side FET [Ω] Turn-on and turn-off voltage of the low-side FET is generally small and the switching loss is small enough to ignore, so that is omitted here. Especially, when turning on the high-side FET under the high power supply voltage condition, the rush-current might be generated by according to self-turn-on of the low-side FET. The parasitic capacitor value of the low-side FET needs to satisfy the following conditions. VTH_Sync > Crss ¯VIN Ciss VTH_Sync Crss Ciss VIN : Threshold voltage of low-side FET [V] : Parasitic feedback capacitance of low-side FET [F] : Parasitic input capacitance of low-side FET [F] : Power supply voltage [V] Also approaches of adding a capacitor close between the gate source pins of the low-side FET or adding resistor between the BST pin and the boost capacitor, and so on are effective as a countermeasure of the self-turn-on(adding resistor between the BST pin and the boost capacitor is also effective to adjust turn-on time of the high-side FET). This device monitors the gate voltage of the switching FET and optimizes the dead time. If the dumping resistor is inserted among DRVH, DRVL and the switching FET gate to adjust turn-on and turn-off time of the switching FET, this function might malfunction. In this device, resistor should not be connected among the DRVH pin, the DRVL pin of IC and the switching FET gate, and should be connected by low impedance as possible. The gate drive power of the switching FET is supplied from LDO (VB) of IC inside. Select switching FET so that the total amount of the switching FET electric charge for 2 channels (QG_Total1, QG_Total2) satisfies the following formula. IVB_MAX > QG_Total1 ¯ fOSC1 + QG_Total2 ¯ fOSC2 IVB_MAX QG_Total1 QG_Total2 fOSC1 fOSC2 : VB load current upper limit value (see the following graph) [A] : Total quantity of charge for the high-side FET and the low-side FET of each CH1 [C] : Total quantity of charge for the high-side FET and the low-side FET of each CH2 [C] : CH1Switching frequency [Hz] : CH2 Switching frequency [Hz] 34 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A VB load current upper limit value [A] 0.08 0.07 0.06 0.05 0.04 0.03 0.02 0.01 0 6 8 10 12 14 16 18 20 22 24 26 28 VIN [V] Moreover, select the total quantity of the high-side FET electric charge as a guide that does not exceed the total quantity of the high-side FET electric charge upper limit value shown below. The total quantity upper limit of electric charge of the high-side FET QG_MAX [nC] 35 From the top line FREQ=GND:CH1 FREQ=GND:CH2 FREQ=OPEN:CH1 FREQ=OPEN:CH2 FREQ=VB:CH1 FREQ=VB:CH2 30 25 20 15 10 5 0 5 10 15 20 25 30 Power supply voltage VIN [V] Whether the mean current value that flows to switching FET is a rated value or less of switching FET is judged. Each rating value for the switching FET can be calculated roughly by the following formula. ID_Main > IOUT_MAX ¯ D ID_Sync > IOUT_MAX ¯ (1 – D) ID_Main ID_Sync IOUT_MAX D : high-side FET drain current [A] : Low-side FET drain current [A] : Maximum load current [A] : On-duty VDSS > VIN VDSS VIN : Voltage between the high-side FET drain and source and the low-side FET drain and source [V] : Power supply voltage [V] DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL 35 MB39A214A Selection of fly-back diode This device is improved by adding the fly-back diode when the conversion efficiency improvement or the suppression of the low-side FET fever is desired, although those are unnecessary to execute normally. The effect is achieved in the condition where the switching frequency is high or output voltage is lower. Select schottky barrier diode (SBD) that the forward current is as small as possible. In this DC/DC control IC, the period for the electric current flow into fly-back diode is limited to dead time period because the synchronous rectification system is adopted. (as for the dead time, see “Output Block” in “ELECTRICAL CHARACTERISTICS”). Each rating for the fly-back diode can be calculated by the following formula. ID ≥ IOUT_MAX ¯fOSC ¯ (tD1 + tD2) ID IOUT_MAX fOSC tD1, tD2 : Forward current rating of SBD [A] : Maximum load current [A] : Switching frequency [Hz] : Dead time [s] IFSM ≥ IOUT_MAX + ΔIL 2 IFSM : Peak forward surge current ratings of SBD [A] IOUT_MAX : Maximum load current [A] : Ripple current peak-to-peak value of inductor [A] ΔIL VR_Fly > VIN VR_Fly VIN : Reverse voltage of fly-back diode direct current [V] : Power supply voltage [V] 36 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A Selection of input capacitor Select the input capacitor whose ESR is as small as possible. The ceramic capacitor is an ideal. Use the tantalum capacitor and the polymer capacitor of the low ESR when a mass capacitor is needed as the ceramic capacitor can not support. The ripple voltage is generated in the power supply voltage by the switching operation of DC/DC. Calculate the lower bound of input capacitor according to an allowable ripple voltage. Calculate the ripple voltage of the power supply from the following formula. ΔVIN = IOUT_MAX CIN ΔVIN IOUT_MAX CIN VIN VOUT fOSC ESR ΔIL ¯ VOUT VIN ¯ fOSC + ESR ¯ (IOUT_MAX + ΔIL 2 ) : Power supply ripple voltage peak-to-peak value [V] : Maximum load current value [A] : Input capacitor value [F] : Power supply voltage [V] : Output setting voltage [V] : Switching frequency [Hz] : Series resistance component of input capacitor [Ω] : Ripple current peak-to-peak value of inductor [A] Capacitor has frequency characteristic, the temperature characteristic, and the bias voltage characteristic, etc. The effective capacitor value might become extremely small depending on the use conditions. Note the effective capacitor value in the use conditions. Calculate ratings of the input capacitor by the following formula: VCIN > VIN VCIN : Withstand voltage of the input capacitor [V] VIN : Power supply voltage [V] Irms ≥ IOMAX ¯ Irms IOMAX VIN VOUT √ VOUT¯ (VIN – VOUT) VIN : Allowable ripple current of input capacitor (effective value) [A] : Maximum load current value [A] : Power supply voltage [V] : Output setting voltage [V] DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL 37 MB39A214A Selection of output capacitor A certain level of ESR is required for stable operation of this IC. Use a tantalum capacitor or polymer capacitor as the output capacitor. If using a ceramic capacitor with low ESR, a resistor should be connected in series with it to increase ESR equivalently. Calculate the output capacitor value by the following formula as a guide. COUT ≥ 1 4 ¯fOSC ¯ ESR COUT fOSC ESR : Output capacitor value [F] : Switching frequency [Hz] : Series resistance of output capacitor [Ω] Moreover, the output capacitor values are also derived from the allowable amount of overshoot and undershoot. The following formula is represented as the worst condition in which the shift time for a sudden load change is 0s. The output capacitor value allow a smaller amount than the value calculated by the following formula when a longer shift time. COUT ≥ COUT ≥ ΔIOUT2 ¯ L …Overshoot condition 2 ¯ VOUT ¯ ΔVOUT_OVER ΔIOUT2 ¯ L ¯ (VOUT + VIN ¯ fOSC ¯ tOFF_MIN) … Undershoot condition 2 ¯ VOUT ¯ ΔVOUT_UNDER ¯ (VIN – VOUT – VIN ¯ fOSC ¯ tOFF_MIN) COUT : Output capacitor value [F] : Allowable amount of output voltage overshoot [V] ΔVOUT_OVER ΔVOUT_UNDER : Allowable amount of output voltage undershoot [V] : Current difference in sudden load change [A] ΔIOUT L VIN VOUT fOSC tOFF_MIN : Inductor value [H] : Power supply voltage [V] : Output setting voltage [V] : Switching frequency [Hz] : Minimum off time When changing to no load suddenly, the output voltage is overshoot, however, the current sink is not executed in the mode other than PWM fix. As a result, the decrement of the output voltage might take a long time. This sometimes results in the stop mode because of the over voltage detection. In the mode other than PWM fix, select the capacitor value so that the overshoot value is set to the over voltage detection voltage value or less (115% of the output setting voltage or less). The capacitor has frequency, operating temperature, and bias voltage characteristics, etc. Therefore, it must be noted that its effective capacitor value may be significantly smaller, depending on the use conditions. 38 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A Calculate each rating of the output capacitor by the following formula: VCOUT > VOUT VCOUT VOUT IRMS ≥ : Withstand voltage of the output capacitor [V] : Output voltage [V] ΔIL 2 3 IRMS ΔIL : Allowable ripple current of output capacitor (effective value) [A] : Ripple current peak-to-peak value of inductor [A] When connecting resistance in series configuration while a ceramic capacitor is in use, the resistor rating is calculated by the following formula. PESR > ESR¯ΔIL2 12 PESR ESR ΔIL : Power dissipation of resistor [W] : Resistor value [Ω] : Ripple current peak-to-peak value of inductor [A] DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL 39 MB39A214A Selection of bootstrap capacitor To drive the gate of high-side FET, the bootstrap capacitor must have enough stored charge. 0.1 µF is assumed to be standard, however, it is necessary to adjust it when the high-side FET QG is big. Consider the capacitor value calculated by the following formula as the lowest value for the bootstrap capacitor and select a thing any more. CBST ≥ 10¯QG CBST QG : Bootstrap capacitor value [F] : Total quantity of charge for the high-side FET gate [C] Calculate ratings of the bootstrap capacitor by the following formula: VCBST > VB VCBST VB : Withstand voltage of the bootstrap capacitor [V] : VB voltage [V] VB pin capacitor 4.7 µF is assumed to be a standard, and when QG of switching FET used is large, it is necessary to adjust it. To suppress the ripple voltage by the switching FET gate drive, consider the capacitor value calculated by the following formula as the lowest value for VB capacitor and select a thing any more. CVB ≥ 50¯QG CVB QG : VB pin capacitor value [F] : Total amount of gate charge of high-side FET and low-side switching FET for 2CH [C] Calculate ratings of the VB pin capacitor by the following formula: VCVB > VB VCVB VB : Withstand voltage of the VB pin capacitor [V] : VB voltage [V] 40 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A Layout Consider the points listed below and do the layout design. y Provide the ground plane as much as possible on the IC mounted face. Connect bypass capacitor connected with the VCC and VB pins, and GND pin of the switching system parts with switching system GND (PGND). Connect other GND connection pins with control system GND (AGND), and separate each GND, and try not to pass the heavy current path through the control system GND (AGND) as much as possible. In that case, connect control system GND (AGND) and switching system GND (PGND) at the single point of GND (PGND) directly below IC. Switching system parts are Input capacitor (CIN), Switching FET, fly-back diode (SBD), inductor (L) and Output capacitor (COUT). y Connect the switching system parts as much as possible on the surface. Avoid the connection through the through-hole as much as possible. y As for GND pins of the switching system parts, provide the through hole at the proximal place, and connect it with GND of internal layer. y Pay the most attention to the loop composed of input capacitor (CIN), switching FET, and fly-back diode (SBD). Consider parts are disposed mutually to be near for making the current loop as small as possible. y Place the bootstrap capacitor (CBST1, CBST2) proximal to BSTx and LXx pins of IC as much as possible. y Connect the line to the LX pin proximal to the drain pin of low-side FET. Also large electric current flows momentary in this net. Wire the line of width of about 0.8 mm as standard, and as short as possible. y Large electric current flows momentary in the net of DRVHx and DRVLx pins connected with the gate of switching FET. Wire the linewidth of about 0.8 mm to be a standard, as short as possible. Take special care about the line of the DRVLx pin, and wire the line as short as possible. y By-pass capacitor (CVCC, CVB) connected with VCC, and VB should be placed close to the pin as much as possible. Also connect the GND pin of the bypass capacitor with GND of internal layer in the proximal through-hole. y Pull the feedback line to be connected to the VOUTx pin of the IC separately from near the output capacitor pin, whenever possible. Consider the line connected with VOUTx and FBx pins to keep away from a switching system parts as much as possible because it is sensitive to the noise. Also, place the output voltage setting resistor connected to this line near IC, and try to shorten the line to the FBx pin. In addition, for the internal layer right under the component mounting place, provide the control system GND (AGND) of few ripple and few spike noises, or provide the ground plane of the power supply as much as possible. Consider that the discharge current momentary flows into the VOUTx pin (about 200 mA at Vout = 5 V) when the DC/DC operation stops, and then sustain the width for the feedback line. There is leaked magnetic flux around the inductor or backside of place equipped with inductor. Line and parts sensitive to noise should be considered to be placed away from the inductor (or backside of place equipped with inductor). Layout example of IC peripheral Layout example of switching system parts High-side FET CBST1 1pin AGND CVCC AGND Through-hole PGND CIN Low-side FET PGND To the LX1 pin PGND Connect AGND and PGND right under IC Internal layer DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL To the LX2 pin SBD(option) SBD (option) COUT Output voltage setting resistor layout CBST2 CIN Low-side FET CVB Surface High-side FET VIN COU T L L VOUT1 Output voltage VOUT1 feedback VOUT2 Output voltage VOUT2 feedback 41 MB39A214A „ REFERENCE DATA Conversion Efficiency vs.Load Current 100 90 90 PFM/PWM 70 60 50 PWM PAF 40 30 VIN = 12 V VOUT1 = 1.0 V FREQ = Open Ta = +25°C 20 10 0 0.001 PFM/PWM 80 Conversion Efficiencyη (%) 80 Conversion Efficiency η (%) Conversion Efficiency vs.Load Current 100 0.01 0.1 70 60 50 40 30 VIN = 12 V VOUT2 = 1.8 V FREQ = Open Ta = +25°C 20 10 1 0 10 0.001 Load Current IOUT1 (A) Switching Frequency vs. Load Current Output Voltage VOUT1 (V) Switching Frequency fosc2 (kHz) 10 VIN = 12 V VOUT1 = 1.0 V FREQ = Open Ta = +25°C PFM/PWM 0.01 0.1 1 10 PWM 100 PAF 10 1 10 0.001 VIN = 12 V VOUT2 = 1.8 V FREQ = Open Ta = +25°C PFM/PWM 0.01 0.1 1 Load Current IOUT1(A) Load Current IOUT2 (A) Output Voltage vs. Load Current Output Voltage vs. Load Current 1.05 1.90 1.04 1.88 1.03 1.86 1.02 PAF PFM/PWM 1.00 PWM 0.98 VIN = 12 V VOUT1 = 1.0 V FREQ = Open Ta = +25°C 0.97 0.96 0.01 0.1 1 10 Load Current IOUT1 (A) 42 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL Output Voltage VOUT2 (V) Switching Frequency fosc1 (kHz) PAF 0.95 0.001 1 Switching Frequency vs. Load Current 100 0.99 0.1 1000 PWM 1.01 0.01 Load Current IOUT2 (A) 1000 1 0.001 PWM PAF 10 1.84 PAF PFM/PWM 1.82 1.80 PWM 1.78 1.76 VIN = 12 V VOUT2 = 1.8 V FREQ = Open Ta = +25°C 1.74 1.72 1.70 0.001 0.01 0.1 1 10 Load Current IOUT2 (A) DS405-00007-1v0-E MB39A214A Ripple Waveform 100 ms/div VOUT1 20 mV/div 20 ms/div VOUT2 20 mV/div VIN=12 V, VOUT1=1.0 V, IOUT1=0 A, MODE=GND, FREQ=Open, Ta=+25°C VIN=12 V, VOUT2=1.8 V, IOUT2=0 A, MODE=GND, FREQ=Open, Ta=+25°C 2 µs/div VOUT1 20 mV/div 2 µs/div VOUT2 20 mV/div VIN=12 V, VOUT1=1.0 V, IOUT1=7 A, MODE=GND, FREQ=Open, Ta=+25°C VIN=12 V, VOUT2=1.8 V, IOUT2=7 A, MODE=GND, FREQ=Open, Ta=+25°C Load Sudden Change Waveform 10 µs/div VOUT1 50 mV/div IOUT1 2 A/div VOUT2 50 mV/div 4A IOUT2 2 A/div 4A 0A 0A VIN=12 V, VOUT1=1.0 V, IOUT1=0 A 10 µs/div 4 A, MODE=GND, FREQ=Open, Ta=+25°C DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL VIN=12 V, VOUT2=1.8 V, IOUT2=0 A 4 A, MODE=GND, FREQ=Open, Ta=+25°C 43 MB39A214A EN Startup and Shutdown Waveform EN1 10 V/div 500 µs/div EN1 10V/div 500 µs/div VOUT1 500 mV/div VOUT1 500 mV/div LX1 10 V/div LX1 10V/div VIN=12 V, VOUT1=1.0 V, IOUT1=7 A (0.14 Ω), MODE=GND, VIN=12V, VOUT2=1.8 V, IOUT2=7 A (0.26 Ω), MODE=GND, FREQ=Open, Ta=+25°C FREQ=Open, Ta=+25°C Output Over Current Waveform 100 µs/div VOUT1 500 mV/div IOUT1 5 A/div LX1 10 V/div Normal operation Over current Under voltage protection limitation VIN=12 V, VOUT1=1.0 V,MODE=VB,FREQ=Open, Ta=+25°C 44 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A „ USAGE PRECAUTION 1. Do not configure the IC over the maximum ratings. If the IC is used over the maximum ratings, the LSI may be permanently damaged. It is preferable for the device to normally operate within the recommended usage conditions. Usage outside of these conditions can have an adverse effect on the reliability of the LSI. 2. Use the device within the recommended operating conditions. The recommended values guarantee the normal LSI operation under the recommended operating conditions. The electrical ratings are guaranteed when the device is used within the recommended operating conditions and under the conditions stated for each item. 3. Printed circuit board ground lines should be set up with consideration for common impedance. 4. Take appropriate measures against static electricity. y Containers for semiconductor materials should have anti-static protection or be made of conductive material. y After mounting, printed circuit boards should be stored and shipped in conductive bags or containers. y Work platforms, tools, and instruments should be properly grounded. y Working personnel should be grounded with resistance of 250 kΩ to 1 MΩ in serial body and ground. 5. Do not apply negative voltages. The use of negative voltages below ─0.3 V may make the parasitic transistor activated to the LSI, and can cause malfunctions. DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL 45 MB39A214A „ ORDERING INFORMATION Part number Package MB39A214APFT 24-pin plastic TSSOP (FPT-24P-M09) Remarks „ EV BOARD ORDERING INFORMATION EV board number EV board version No. Remarks MB39A214A-EVB-01 MB39A214A-EVB-01 Rev. 1.0 TSSOP-24 46 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A „ RoHS COMPLIANCE INFORMATION OF LEAD (Pb) FREE VERSION The LSI products of FUJITSU SEMICONDUCTOR with “E1” are compliant with RoHS Directive, and has observed the standard of lead, cadmium, mercury, Hexavalent chromium, polybrominated biphenyls (PBB), and polybrominated diphenyl ethers (PBDE). A product whose part number has trailing characters “E1” is RoHS compliant. „ MARKING FORMAT (Lead Free version) 39A214A XXXX E1 XXX INDEX Lead-free version DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL 47 MB39A214A „ LABELING SAMPLE (Lead free version) Lead-free mark JEITA logo JEDEC logo MB123456P - 789 - GE1 (3N) 1MB123456P-789-GE1 1000 (3N)2 1561190005 107210 G Pb QC PASS PCS 1,000 MB123456P - 789 - GE1 2006/03/01 ASSEMBLED IN JAPAN MB123456P - 789 - GE1 1561190005 The part number of a lead-free product has the trailing characters "E1". 48 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL 1/1 0605 - Z01A 1000 "ASSEMBLED IN CHINA" is printed on the label of a product assembled in China. DS405-00007-1v0-E MB39A214A „ MB39A214APFT RECOMMENDED CONDITIONS OF MOISTURE SENSITIVITY LEVEL [FUJITSU SEMICONDUCTOR Recommended Mounting Conditions] Item Condition Mounting Method IR (infrared reflow), warm air reflow Mounting times 2 times Storage period Storage conditions Before opening Please use it within two years after manufacture. From opening to the 2nd reflow Less than 8 days When the storage period after opening was exceeded Please process within 8 days after baking (125°C ±3°C, 24H+ 2H/─0H) . Baking can be performed up to two times. 5°C to 30°C, 70% RH or less (the lowest possible humidity) [Mounting Conditions] (1) IR (infrared reflow) 260°C 245°C Main heating 170 °C to 190 °C (b) RT (e) Cooling (d) (e) (d') (a) "M" rank : 250°C Max (a) Temperature Increase gradient (b) Preliminary heating (c) Temperature Increase gradient (d) Peak temperature (d') Main Heating (c) : Average 1°C/s to 4°C /s : Temperature 170°C to 190°C, 60 s to 180 s : Average 1°C /s to 4°C /s : Temperature 250°C Max; 245°C or more, 10 s or less : Temperature 230°C or more, 40 s or less or Temperature 225°C or more, 60 s or less or Temperature 220°C or more, 80 s or less : Natural cooling or forced cooling Note: Temperature : the top of the package bod DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL 49 MB39A214A (2) Manual soldering (partial heating method) Item Condition Before opening Within two years after manufacture Between opening and mounting Within two years after manufacture (No need to control moisture during the storage period because of the partial heating method.) Storage period Storage conditions 5°C to 30°C, 70% RH or less (the lowest possible humidity) Mounting conditions Temperature at the tip of a soldering iron: 400°C Max Time: Five seconds or below per pin* *: Make sure that the tip of a soldering iron does not come in contact with the package body. 50 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A „ PACKAGE DIMENSIONS 24-pin plastic TSSOP Lead pitch 0.50 mm Package width × package length 4.40 mm × 6.50 mm Lead shape Gullwing Sealing method Pl asti c mol d Mounting height 1.20 mm MAX Weight 0.08 g (FPT-24P-M09) 24-pin plastic TSSOP (FPT-24P-M09) Note 1) Pins width and pins thickness include plating thickness. Note 2) Pins width do not include tie bar cutting remainder. Note 3) #: These dimensions do not include resin protrusion. # 6.50± 0.10 (.256±. 004) 0.145± 0.045 (.0057±. 0018) 13 24 BTM E-MARK # 4.40± 0.10 6.40± 0.20 (.173±. 004)(.252±. 008) INDEX Details of "A" part +0.10 1.10 –0.15 +.004 .043 –.006 1 12 0.50(.020) "A" +0.07 0.20 –0.02 +.003 .008 –.001 (Mounting height) 0.13(.005) M 0~8° 0.60± 0.15 (.024±. 006) 0.10± 0.05 (Stand off) (.004±. 002) 0.10(.004) C 2007-2010 FUJITSU SEMICONDUCTOR LIMITED F24032S-c-2-5 Dimensions in mm (inches). Note: The values in parentheses are reference values. Please check the latest package dimension at the following URL. http://edevice.fujitsu.com/package/en-search/ DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL 51 MB39A214A „ CONTENTS page „ „ „ „ „ „ „ „ „ „ „ „ „ „ „ „ „ „ „ „ „ „ „ „ „ DESCRIPTION................................................................................................................................. 1 FEATURES ....................................................................................................................................... 1 APPLICATIONS...............................................................................................................................1 PIN ASSIGNMENT.......................................................................................................................... 2 PIN DESCRIPTIONS ....................................................................................................................... 3 BLOCK DIAGRAM ......................................................................................................................... 4 ABSOLUTE MAXIMUM RATINGS ..............................................................................................5 RECOMMENDED OPERATING CONDITIONS...........................................................................6 ELECTRICAL CHARACTERISTICS ............................................................................................. 7 TYPICAL CHARACTERISTICS...................................................................................................10 FUNCTION.....................................................................................................................................13 I/O PIN EQUIVALENT CIRCUIT DIAGRAM............................................................................. 22 EXAMPLE APPLICATION CIRCUIT ..........................................................................................24 PART LIST......................................................................................................................................25 APPLICATION NOTE ...................................................................................................................26 REFERENCE DATA.......................................................................................................................42 USAGE PRECAUTION .................................................................................................................45 ORDERING INFORMATION........................................................................................................46 EV BOARD ORDERING INFORMATION .................................................................................. 46 RoHS COMPLIANCE INFORMATION OF LEAD (Pb) FREE VERSION ................................47 MARKING FORMAT (Lead Free version)....................................................................................47 LABELING SAMPLE (Lead free version) ....................................................................................48 MB39A214APFT RECOMMENDED CONDITIONS OF MOISTURE SENSITIVITY LEVEL49 PACKAGE DIMENSIONS............................................................................................................. 51 CONTENTS ....................................................................................................................................52 52 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL 53 MB39A214A 54 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E MB39A214A DS405-00007-1v0-E Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL 55 MB39A214A FUJITSU SEMICONDUCTOR LIMITED Nomura Fudosan Shin-yokohama Bldg. 10-23, Shin-yokohama 2-Chome, Kohoku-ku Yokohama Kanagawa 222-0033, Japan Tel: +81-45-415-5858 http://jp.fujitsu.com/fsl/en/ For further information please contact: North and South America FUJITSU SEMICONDUCTOR AMERICA, INC. 1250 E. Arques Avenue, M/S 333 Sunnyvale, CA 94085-5401, U.S.A. Tel: +1-408-737-5600 Fax: +1-408-737-5999 http://us.fujitsu.com/micro/ Asia Pacific FUJITSU SEMICONDUCTOR ASIA PTE. LTD. 151 Lorong Chuan, #05-08 New Tech Park 556741 Singapore Tel : +65-6281-0770 Fax : +65-6281-0220 http://sg.fujitsu.com/semiconductor/ Europe FUJITSU SEMICONDUCTOR EUROPE GmbH Pittlerstrasse 47, 63225 Langen, Germany Tel: +49-6103-690-0 Fax: +49-6103-690-122 http://emea.fujitsu.com/semiconductor/ FUJITSU SEMICONDUCTOR SHANGHAI CO., LTD. 30F, Kerry Parkside, 1155 Fang Dian Road, Pudong District, Shanghai 201204, China Tel : +86-21-6146-3688 Fax : +86-21-6146-3660 http://cn.fujitsu.com/fss/ Korea FUJITSU SEMICONDUCTOR KOREA LTD. 902 Kosmo Tower Building, 1002 Daechi-Dong, Gangnam-Gu, Seoul 135-280, Republic of Korea Tel: +82-2-3484-7100 Fax: +82-2-3484-7111 http://kr.fujitsu.com/fsk/ FUJITSU SEMICONDUCTOR PACIFIC ASIA LTD. 10/F., World Commerce Centre, 11 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel : +852-2377-0226 Fax : +852-2376-3269 http://cn.fujitsu.com/fsp/ Specifications are subject to change without notice. For further information please contact each office. All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with sales representatives before ordering. The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of FUJITSU SEMICONDUCTOR device; FUJITSU SEMICONDUCTOR does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. FUJITSU SEMICONDUCTOR assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU SEMICONDUCTOR or any third party or does FUJITSU SEMICONDUCTOR warrant non-infringement of any third-party's intellectual property right or other right by using such information. FUJITSU SEMICONDUCTOR assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that FUJITSU SEMICONDUCTOR will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws. The company names and brand names herein are the trademarks or registered trademarks of their respective owners. Edited: Sales Promotion Department 56 Limitation : development tool vendor use only FUJITSU SEMICONDUCTOR CONFIDENTIAL DS405-00007-1v0-E