MB96F346ASA

FUJITSU SEMICONDUCTOR DATA SHEET FME-MB96340 rev 10 16-bit Proprietary Microcontroller CMOS F2MC-16FX MB96340 Series MB96345/346 MB96F345 *1 MB96F346/F347/F348 ■ DESCRIPTION MB96340 series is based on Fujitsu’s advanced 16FX architecture (16-bit with instruction pipeline for RISC-like performance). The CPU uses the same instruction set as the established 16LX series - thus allowing for easy migration of 16LX Software to the new 16FX products. 16FX improvements compared to the previous generation include significantly improved performance - even at the same operation frequency, reduced power consumption and faster start-up time. For highest processing speed at optimized power consumption an internal PLL can be selected to supply the CPU with up to 56MHz operation frequency from an external 4MHz resonator. The result is a minimum instruction cycle time of 17.8ns going together with excellent EMI behavior. An on-chip clock modulation circuit significantly reduces emission peaks in the frequency spectrum. The emitted power is minimized by the on-chip voltage regulator that reduces the internal CPU voltage. A flexible clock tree allows to select suitable operation frequencies for peripheral resources independent of the CPU speed. *1: These devices are under development and specification is preliminary. These products under development may change its specification without notice. Note: F2MC is the abbreviation of Fujitsu Flexible Microcontroller For the information for microcontroller supports, see the following web site. This web site includes the "Customer Design Review Supplement" which provides the latest cautions on system development and the minimal requirements to be checked to prevent problems before the system development. http://edevice.fujitsu.com/micom/en-support/ Copyright©2010 FUJITSU SEMICONDUCTOR LIMITED All rights reserved 2010.6 MB96340 Series ■ FEATURES Feature Technology • 0.18µm CMOS • F2MC-16FX CPU • Up to 56 MHz internal, 17.8 ns instruction cycle time CPU • Optimized instruction set for controller applications (bit, byte, word and long-word data types; 23 different addressing modes; barrel shift; variety of pointers) • 8-byte instruction execution queue • Signed multiply (16-bit × 16-bit) and divide (32-bit/16-bit) instructions available • On-chip PLL clock multiplier (x1 - x25, x1 when PLL stop) • 3 MHz - 16 MHz external crystal oscillator clock (maximum frequency when using ceramic resonator depends on Q-factor). • Up to 56 MHz external clock for devices with fast clock input feature • 32-100 kHz subsystem quartz clock System clock • 100kHz/2MHz internal RC clock for quick and safe startup, oscillator stop detection, watchdog • Clock source selectable from main- and subclock oscillator (part number suffix “W”) and on-chip RC oscillator, independently for CPU and 2 clock domains of peripherals. • Low Power Consumption - 13 operating modes : (different Run, Sleep, Timer modes, Stop mode) • Clock modulator On-chip voltage regula- • Internal voltage regulator supports reduced internal MCU voltage, offering low EMI tor and low power consumption figures Low voltage reset Code Security Memory Patch Function DMA Interrupts • Reset is generated when supply voltage is below minimum. • Protects ROM content from unintended read-out • Replaces ROM content • Can also be used to implement embedded debug support • Automatic transfer function independent of CPU, can be assigned freely to resources • Fast Interrupt processing • 8 programmable priority levels • Non-Maskable Interrupt (NMI) Timers • Three independent clock timers (23-bit RC clock timer, 23-bit Main clock timer, 17-bit Sub clock timer) • Watchdog Timer Description 2 FME-MB96340 rev 10 MB96340 Series Feature • ISO16845 certified • Bit rates up to 1 Mbit/s • 32 message objects CAN • Each message object has its own identifier mask • Programmable FIFO mode (concatenation of message objects) • Maskable interrupt • Disabled Automatic Retransmission mode for Time Triggered CAN applications • Programmable loop-back mode for self-test operation • Full duplex USARTs (SCI/LIN) USART • Wide range of baud rate settings using a dedicated reload timer • Special synchronous options for adapting to different synchronous serial protocols • LIN functionality working either as master or slave LIN device I2C • Up to 400 kbps • Master and Slave functionality, 7-bit and 10-bit addressing • SAR-type A/D converter • 10-bit resolution • Signals interrupt on conversion end, single conversion mode, continuous conversion mode, stop conversion mode, activation by software, external trigger or reload timer A/D Converter Reference Voltage switch Reload Timers • 2 independent positive A/D converter reference voltages available • 16-bit wide • Prescaler with 1/21, 1/22, 1/23, 1/24, 1/25, 1/26 of peripheral clock frequency • Event count function Free Running Timers • Signals an interrupt on overflow, supports timer clear upon match with Output Compare (0, 4), Prescaler with 1, 1/21, 1/22, 1/23, 1/24, 1/25, 1/26, 1/27,1/28 of peripheral clock frequency • 16-bit wide Input Capture Units • Signals an interrupt upon external event • Rising edge, falling edge or rising & falling edge sensitive • 16-bit wide Output Compare Units • Signals an interrupt when a match with 16-bit I/O Timer occurs • A pair of compare registers can be used to generate an output signal. Description • Supports CAN protocol version 2.0 part A and B FME-MB96340 rev 10 3 MB96340 Series Feature Description • 16-bit down counter, cycle and duty setting registers • Interrupt at trigger, counter borrow and/or duty match Programmable Pulse Generator • PWM operation and one-shot operation • Internal prescaler allows 1, 1/4, 1/16, 1/64 of peripheral clock as counter clock and Reload timer underflow as clock input • Can be triggered by software or reload timer • Can be clocked either from sub oscillator (devices with part number suffix “W”), main oscillator or from the RC oscillator Real Time Clock • Facility to correct oscillation deviation of Sub clock or RC oscillator clock (clock calibration) • Read/write accessible second/minute/hour registers • Can signal interrupts every half second/second/minute/hour/day • Internal clock divider and prescaler provide exact 1s clock • Edge sensitive or level sensitive External Interrupts • Interrupt mask and pending bit per channel • Each available CAN channel RX has an external interrupt for wake-up • Selected USART channels SIN have an external interrupt for wake-up • Disabled after reset Non Maskable Interrupt • Once enabled, can not be disabled other than by reset. • Level high or level low sensitive • Pin shared with external interrupt 0. • 8-bit or 16-bit bidirectional data • Up to 24-bit addresses • 6 chip select signals External bus interface • Multiplexed address/data lines • Wait state request • External bus master possible • Timing programmable • Monitors an external voltage and generates an interrupt in case of a voltage lower or higher than the defined thresholds Alarm comparator • Threshold voltages defined externally or generated internally • Status is readable, interrupts can be masked separately 4 FME-MB96340 rev 10 MB96340 Series Feature Description • Virtually all external pins can be used as general purpose I/O • All push-pull outputs (except when used as I2C SDA/SCL line) • Bit-wise programmable as input/output or peripheral signal I/O Ports • Bit-wise programmable input enable • Bit-wise programmable input levels: Automotive / CMOS-Schmitt trigger / TTL (TTL levels not supported by all devices) • Bit-wise programmable pull-up resistor • Bit-wise programmable output driving strength for EMI optimization Packages • 100-pin plastic QFP and LQFP • Supports automatic programming, Embedded Algorithm • Write/Erase/Erase-Suspend/Resume commands • A flag indicating completion of the algorithm • Number of erase cycles: 10,000 times Flash Memory • Data retention time: 20 years • Erase can be performed on each sector individually • Sector protection • Flash Security feature to protect the content of the Flash • Low voltage detection during Flash erase FME-MB96340 rev 10 5 MB96340 Series ■ PRODUCT LINEUP Features Product type Product options YS RS YW RW TS HS TW HW FS DS FW DW AS CS AW CW Flash/ROM 160KB 224KB [Flash A: 160KB, Data Flash A: 64KB] 288KB 416KB 544KB 576KB [Flash A: 544KB, Flash B: 32KB] Package RAM 8KB 8KB 16KB 16KB 24KB 24KB MB96V300B Evaluation sample MB96(F)34x Flash product: MB96F34x Mask ROM product: MB9634x Low voltage reset persistently on / Single clock Low voltage reset can be disabled / Single clock Low voltage reset persistently on / Dual clock Low voltage reset can be disabled / Dual clock indep. 32KB Flash / Low voltage reset persistently on / Single clock indep. 32KB Flash / Low voltage reset can be disabled / Single clock indep. 32KB Flash / Low voltage reset persistently on / Dual clock indep. 32KB Flash / Low voltage reset can be disabled / Dual clock NA 64KB Data Flash / Low voltage reset persistently on / Single clock 64KB Data Flash / Low voltage reset can be disabled / Single clock 64KB Data Flash / Low voltage reset persistently on / Dual clock 64KB Data Flash / Low voltage reset can be disabled / Dual clock No CAN / Low voltage reset can be disabled / Single clock devices No CAN / indep. 32KB Flash / Low voltage reset can be disabled / Single clock No CAN / Low voltage reset can be disabled / Dual clock No CAN / indep. 32KB Flash / Low voltage reset can be disabled / Dual clock MB96345Y *1, MB96345R *1 MB96F345F *1, MB96F345D *1 ROM/Flash memory emulation by external RAM, 92KB internal RAM MB96F346Y, MB96346Y *1, MB96F346R, MB96346R *1, MB96F346A MB96F347Y, MB96F347R, MB96F347A MB96F348Y, MB96F348R, MB96F348A MB96F348T, MB96F348H, MB96F348C BGA416 FPT-100P-M20 FPT-100P-M22 6 FME-MB96340 rev 10 MB96340 Series Features DMA USART I2C A/D Converter A/D Converter Reference Voltage switch 16-bit Reload Timer 16-bit Free-Running Timer 16-bit Output Compare 16-bit Input Capture 16-bit Programmable Pulse Generator CAN Interface External Interrupts Non-Maskable Interrupt Real Time Clock I/O Ports Alarm comparator External bus interface Chip select Clock output function Low voltage reset On-chip RC-oscillator 136 2 channels Yes MB96V300B 16 channels 10 channels 2 channels 40 channels yes 6 channels + 1 channel (for PPG) 4 channels 12 channels 12 channels 20 channels MB96(F)34x 6 channels 7 channels 2 channels 24 channels yes (except MB96F345Dyy or MB96F345Fyy) 4 channels + 1 channel (for PPG) 2 channels 8 channels 8 channels 16 channels MB96(F)34xAyy or MB96(F)34xCyy: no MB96F345Dyy or MB96F345Fyy: 1 channel others: 2 channels 16 channels 1 channel 1 80 for part number with suffix "W", 82 for part number with suffix "S" MB96F345Dyy or MB96F345Fyy: no others: 2 channels Yes (multiplexed address/data) 6 signals 2 channels Yes Yes 5 channels *1: These devices are under development and specification is preliminary. These products under development may change its specification without notice. FME-MB96340 rev 10 7 MB96340 Series ■ BLOCK DIAGRAM Block diagram of MB96(F)34x AD00 ... AD15 A16 ... A23 ALE RDX WR(L)X, WRHX HRQ HAKX NMI, NMI_R RDY ECLK LBX, UBX CS0 ... CS5 External Bus Interface 16FX CPU Interrupt Controller Flash Memory A Flash Memory B or Data Flash A *2 CKOT0, CKOT1 CKOTX0, CKOTX1 X0, X1 X0A, X1A *1 RSTX MD0...MD2 Memory Patch Unit Clock & Mode Controller 16FX Core Bus (CLKB) DMA Controller Watchdog Peripheral Bus Bridge Peripheral Bus Bridge RAM Boot ROM Voltage Regulator Peripheral Bus 2 (CLKP2) SDA0, SDA1 SCL0, SCL1 AVCC AVSS AVRH AVRL/AVRH2 *5 AN0 ... AN23 ADTG, ADTG_R TIN0 ... TIN3 TOT0 ... TOT3 FRCK0 IN0 ... IN3 OUT0 ... OUT3 FRCK1 IN4 ... IN7 OUT4 ... OUT7 INT0 ... INT15 INT0_R ... INT2_R INT4_R, INT5_R INT7_R ... INT15_R INT3_R1 I2C 2 ch. VCC VSS C CAN Interface 2 ch. TX0, TX1 *3 RX0, RX1 *3 10-bit ADC 24 ch. Peripheral Bus 1 (CLKP1) 16-bit Reload Timer 4 ch. I/O Timer 0 ICU 0/1/2/3 OCU 0/1/2/3 I/O Timer 1 ICU 4/5/6/7 OCU 4/5/6/7 USART 7 ch. Alarm Comparator 2 ch. *4 16-bit PPG 16 ch. RLT6 SIN0...SIN3, SIN2_R, SIN7_R...SIN9_R SOT0...SOT3, SOT2_R, SOT7_R...SOT9_R SCK0...SCK3, SCK2_R, SCK7_R...SCK9_R ALARM0 *4 ALARM1 *4 TTG0 ... TTG15 PPG0 ... PPG15 External Interrupt Real Time Clock WOT *1: X0A, X1A only available on MB96(F)34xyWy *2: Flash B only available on MB96F34xCyy, MB96F34xHyy or MB96F34xTyy Data Flash A only available on MB96F34xDyy or MB96F34xFyy *3: CAN interfaces are not available on MB96(F)34xAyy or MB96(F)34xCyy CAN1 is not available on MB96F345Dyy or MB96F345Fyy *4: Alarm comparator is not available on MB96F345Dyy or MB96F345Fyy *5: A/D converter reference voltage switch is not available on MB96F345Dyy or MB96F345Fyy 8 FME-MB96340 rev 10 MB96340 Series ■ PIN ASSIGNMENTS Pin assignment of MB96(F)34x (FPT-100P-M22) P08_0/TIN0/CKOTX0/ADTG/INT12_R P08_1/TOT0/CKOT0/INT13_R P00_3/AD03/INT11/SCK8_R P00_2/AD02/INT10/SIN7_R P00_1/AD01/INT9/SOT7_R P00_0/AD00/INT8/SCK7_R P07_6/AN22/INT6/SOT9_R P08_2/SIN0/TIN2/INT14_R P07_7/AN23/INT7/SIN9_R P08_4/SCK0/INT15_R P10_0/RX0/INT8_R *2 P08_5/SIN1/INT1_R P09_3/PPG11/CS4 P09_2/PPG10/CS5 P08_3/SOT0/TOT2 P09_0/PPG8/UBX P09_7/OUT3/CS0 P09_6/OUT2/CS1 P09_5/OUT1/CS2 P09_4/OUT0/CS3 P09_1/PPG9/LBX P10_1/TX0 *2 P08_7/SCK1 P08_6/SOT1 RSTX MD0 MD1 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 P00_4/AD04/INT12/SOT8_R P00_5/AD05/INT13/SIN8_R P00_6/AD06/INT14 P00_7/AD07/INT15 P01_0/AD08/CKOT1/TIN1 P01_1/AD09/CKOTX1/TOT1 P01_2/AD10/INT11_R/SIN3 P01_3/AD11/SOT3 P01_4/AD12/SCK3 Vcc Vss X1 X0 P01_5/AD13/INT7_R/SIN2_R P01_6/AD14/SOT2_R P01_7/AD15/SCK2_R P02_0/A16/PPG12 P02_1/A17/PPG13 P02_2/A18/PPG14 P02_3/A19/PPG15 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 P07_5/AN21/INT5/SCK9_R P07_4/AN20/INT4 P07_3/AN19/INT3 P07_2/AN18/INT2 P07_1/AN17/INT1 P07_0/AN16/INT0/NMI Vss P06_7/AN7/PPG7 P06_6/AN6/PPG6 P06_5/AN5/PPG5 P06_4/AN4/PPG4 P06_3/AN3/PPG3 P06_2/AN2/PPG2 P06_1/AN1/PPG1 P06_0/AN0/PPG0 AVss AVRL/AVRH2 *4 AVRH AVcc P05_7/AN15/INT5_R QFP - 100 Package code (mold) FPT-100P-M22 P04_2/IN6/RX1/INT9_R/TTG6/TTG14 *2 P04_3/IN7/TX1/TTG7/TTG15 *2 P03_3/WRHX P03_1/RDX/IN5/TTG5/TTG13 P03_0/ALE/IN4/TTG4/TTG12 P05_4/AN12/TOT3/INT2_R P03_4/HRQ/OUT4 P03_5/HAKX/OUT5 P03_6/RDY/OUT6 P02_4/A20/TTG8/TTG0/IN0 P02_6/A22/IN2/TTG2/TTG10 P02_7/A23/IN3/TTG3/TTG11 P03_2/WRLX/WRX/INT10_R P05_0/AN8/ALARM0/SIN2/INT3_R1 *3 P02_5/A21/TTG9/TTG1/IN1/ADTG_R P05_1/AN9/ALARM1/SOT2 *3 P05_3/AN11/TIN3/WOT *1: MB96(F)34xyWy: X0A, X1A MB96(F)34xySy: P04_0, P04_1 *2: TX0, RX0, TX1, RX1 are not available on MB96(F)34xAyy or MB96(F)34xCyy TX1, RX1 are not available on MB96F345Dyy or MB96F345Fyy *3: ALARM0, ALARM1 are not available on MB96F345Dyy or MB96F345Fyy *4: AVRH2 is not available on MB96F345Dyy or MB96F345Fyy (FPT-100P-M22) Remark: MB96(F)34x products are pin-compatible to F2MC-16LX family MB90340 series. FME-MB96340 rev 10 P05_5/AN13/INT0_R/NMI_R P05_6/AN14/INT4_R P04_4/SDA0/FRCK0 P04_6/SDA1 *1 *1 Vcc Vss C P04_5/SCL0/FRCK1 P03_7/ECLK/OUT7 P05_2/AN10/SCK2 X0A/P04_0 X1A/P04_1 P04_7/SCL1 MD2 Vss Vcc 9 MB96340 Series Pin assignment of MB96(F)34x (FPT-100P-M20) P08_0/TIN0/CKOTX0/ADTG/INT12_R P08_1/TOT0/CKOT0/INT13_R P00_0/AD00/INT8/SCK7_R P07_6/AN22/INT6/SOT9_R P08_2/SIN0/TIN2/INT14_R P07_7/AN23/INT7/SIN9_R P08_4/SCK0/INT15_R *2 P08_5/SIN1/INT1_R P10_0/RX0/INT8_R P09_3/PPG11/CS4 P09_2/PPG10/CS5 P08_3/SOT0/TOT2 P09_0/PPG8/UBX P09_7/OUT3/CS0 P09_6/OUT2/CS1 P09_5/OUT1/CS2 P09_4/OUT0/CS3 P09_1/PPG9/LBX *2 P08_7/SCK1 P08_6/SOT1 P10_1/TX0 RSTX P00_1AD01/INT9/SOT7_R P00_2/AD02/INT10/SIN7_R P00_3/AD03/INT11/SCK8_R P00_4/AD04/INT12/SOT8_R P00_5/AD05/INT13/SIN8_R P00_6/AD06/INT14 P00_7/AD07/INT15 P01_0/AD08/CKOT1/TIN1 P01_1/AD09/CKOTX1/TOT1 P01_2/AD10/INT11_R/SIN3 P01_3/AD11/SOT3 P01_4/AD12/SCK3 Vcc Vss X1 X0 P01_5/AD13/INT7_R/SIN2_R P01_6/AD14/SOT2_R P01_7/AD15/SCK2_R P02_0/A16/PPG12 P02_1/A17/PPG13 P02_2/A18/PPG14 P02_3/A19/PPG15 P02_4/A20/TTG8/TTG0/IN0 P02_5/A21/TTG9/TTG1/IN1/ADTG_R 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 MD0 Vss Vcc MD1 MD2 P07_5/AN21/INT5/SCK9_R P07_4/AN20/INT4 P07_3/AN19/INT3 P07_2/AN18/INT2 P07_1/AN17/INT1 P07_0/AN16/INT0/NMI Vss P06_7/AN7/PPG7 P06_6/AN6/PPG6 P06_5/AN5/PPG5 P06_4/AN4/PPG4 P06_3/AN3/PPG3 P06_2/AN2/PPG2 P06_1/AN1/PPG1 P06_0/AN0/PPG0 AVss AVRL/AVRH2 *4 AVRH AVcc P05_7/AN15/INT5_R P05_6/AN14/INT4_R P05_5/AN13/INT0_R/NMI_R P05_4/AN12/TOT3/INT2_R LQFP - 100 Package code (mold) FPT-100P-M20 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 100 1 P02_6/A22/IN2/TTG2/TTG10 2 3 4 P03_1/RDX/IN5/TTG5/TTG13 5 P03_2/WRLX/WRX/INT10_R 6 P03_3/WRHX 78 P03_5/HAKX/OUT5 P03_4/HRQ/OUT4 26 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 P04_2/IN6/RX1/INT9_R/TTG6/TTG14 *2 P04_3/IN7/TX1/TTG7/TTG15 *2 X0A/P04_0 *1 P04_4/SDA0/FRCK0 P04_6/SDA1 P05_0/AN8/ALARM0/SIN2/INT3_R1 *3 P05_1/AN9/ALARM1/SOT2 *3 P05_3/AN11/TIN3/WOT C P04_5/SCL0/FRCK1 P03_7/ECLK/OUT7 P05_2/AN10/SCK2 *1 P02_7/A23/IN3/TTG3/TTG11 P03_0/ALE/IN4/TTG4/TTG12 P03_6/RDY/OUT6 *1: MB96(F)34xyWy: X0A, X1A MB96(F)34xySy: P04_0, P04_1 *2: TX0, RX0, TX1, RX1 are not available on MB96(F)34xAyy or MB96(F)34xCyy TX1, RX1 are not available on MB96F345Dyy or MB96F345Fyy *3: ALARM0, ALARM1 are not available on MB96F345Dyy or MB96F345Fyy *4: AVRH2 is not available on MB96F345Dyy or MB96F345Fyy (FPT-100P-M20) Remark: MB96(F)34x products are pin-compatible to F2MC-16LX family MB90340 series. 10 X1A/P04_1 P04_7/SCL1 Vcc Vss FME-MB96340 rev 10 MB96340 Series ■ PIN FUNCTION DESCRIPTION Pin Function description (1 of 2) Pin name ADn ADTG ADTG_R ALARMn ALE An ANn AVCC AVRH AVRH2 AVRL AVSS C CKOTn CKOTXn ECLK CSn FRCKn HAKX HRQ INn INTn INTn_R LBX MDn NMI NMI_R OUTn Feature External bus ADC ADC Alarm comparator External bus External bus ADC Supply ADC ADC ADC Supply Voltage regulator Clock output function Clock output function External bus External bus Free Running Timer External bus External bus ICU External Interrupt External Interrupt External bus Core External Interrupt External Interrupt OCU Description External bus interface (multiplexed mode) address output and data input/output A/D converter trigger input Relocated A/D converter trigger input Alarm Comparator n input External bus Address Latch Enable output External bus address output A/D converter channel n input Analog circuits power supply A/D converter high reference voltage input Alternative A/D converter high reference voltage input A/D converter low reference voltage input Analog circuits power supply Internally regulated power supply stabilization capacitor pin Clock Output function n output Clock Output function n inverted output External bus clock output External bus chip select n output Free Running Timer n input External bus Hold Acknowledge External bus Hold Request Input Capture Unit n input External Interrupt n input Relocated External Interrupt n input External Bus Interface Lower Byte select strobe output Input pins for specifying the operating mode. Non-Maskable Interrupt input Relocated Non-Maskable Interrupt input Output Compare Unit n waveform output FME-MB96340 rev 10 11 MB96340 Series Pin Function description (2 of 2) Pin name Pxx_n PPGn RDX RDY RSTX RXn SCKn SCKn_R SCLn SDAn SINn SINn_R SOTn SOTn_R TINn TOTn TTGn TXn UBX VCC VSS WOT WRHX WRLX/WRX X0 X0A X1 X1A Feature GPIO PPG External bus External bus Core CAN USART USART I2C I2C USART USART USART USART Reload Timer Reload Timer PPG CAN External bus Supply Supply RTC External bus External bus Clock Clock Clock Clock Description General purpose IO Programmable Pulse Generator n output External bus interface read strobe output External bus interface external wait state request input Reset input CAN interface n RX input USART n serial clock input/output Relocated USART n serial clock input/output I2C interface n clock I/O input/output I2C interface n serial data I/O input/output USART n serial data input Relocated USART n serial data input USART n serial data output Relocated USART n serial data output Reload Timer n event input Reload Timer n output Programmable Pulse Generator n trigger input CAN interface n TX output External Bus Interface Upper Byte select strobe output Power supply Power supply Real Timer clock output External bus High byte write strobe output External bus Low byte / Word write strobe output Oscillator input Subclock Oscillator input (only for devices with suffix "W") Oscillator output Subclock Oscillator output (only for devices with suffix "W") 12 FME-MB96340 rev 10 MB96340 Series ■ PIN CIRCUIT TYPE Pin circuit types FPT-100P-M20 FPT-100P-M22 Pin no. 1-10 11,12 11,12 13,14 15 16,17 18-21 22-29 30 31-32 33 34 to 41 42 43 to 48 49 to 51 52 53 to 54 55 to 62 63, 64 65 to 87 88,89 90, 91 92-100 Circuit type *1 H B *2 H *3 Supply F H N I Supply G Supply I Supply I C E I H Supply H Supply A H Pin no. 1-12 13, 14 13, 14 15,16 17 18,19 20-23 24-31 32 33-34 35 36 to 43 44 45 to 50 51 to 53 54 55 to 56 57 to 64 65, 66 67 to 89 90, 91 92, 93 94 to 100 Circuit type *1 H B *2 H *3 Supply F H N I Supply G Supply I Supply I C E I H Supply H Supply A H *1: Please refer to “■ I/O CIRCUIT TYPE” for details on the I/O circuit types *2: Devices with suffix ”W” *3: Devices without suffix ”W” FME-MB96340 rev 10 13 MB96340 Series ■ I/O CIRCUIT TYPE Type A X1 R Circuit Remarks High-speed oscillation circuit: • Programmable between oscillation mode (external crystal or resonator connected to X0/X1 pins) and Fast external Clock Input (FCI) mode (external clock connected to X0 pin) • Programmable feedback resistor = approx. 2 * 0.5 MΩ. Feedback resistor is grounded in the center when the oscillator is disabled or in FCI mode 0 MRFBE 1 Xout R FCI X0 FCI or osc disable B X1A R Xout Low-speed oscillation circuit: • Programmable feedback resistor = approx. 2 * 5 MΩ. Feedback resistor is grounded in the center when the oscillator is disabled SRFBE R X0A osc disable C R Hysteresis inputs • Mask ROM and EVA device: CMOS Hysteresis input pin • Flash device: CMOS input pin • CMOS Hysteresis input pin • Pull-up resistor value: approx. 50 kΩ E Pull-up Resistor R Hysteresis inputs 14 FME-MB96340 rev 10 MB96340 Series Type F Circuit Remarks • Power supply input protection circuit G ANE AVR ANE • A/D converter ref+ (AVRH/AVRH2) power supply input pin with protection circuit • Flash devices do not have a protection circuit against VCC for pins AVRH/AVRH2 • Devices without AVRH reference switch do not have an analog switch for the AVRL pin H pull-up control Pout Nout R Standby control for input shutdown Standby control for input shutdown Standby control for input shutdown Standby control for input shutdown Hysteresis input • CMOS level output (programmable IOL = 5mA, IOH = -5mA and IOL = 2mA, IOH = -2mA) • 2 different CMOS hysteresis inputs with input shutdown function * • Automotive input with input shutdown function • TTL input with input shutdown function * • Programmable pull-up resistor: 50kΩ approx. Note: MB96F345Dyy or MB96F345Fyy: Only Automotive input and CMOS hysteresis input (0.7/0.3) are supported Hysteresis input Automotive input TTL input FME-MB96340 rev 10 15 MB96340 Series Type I Pull-up control Circuit Remarks • CMOS level output (programmable IOL = 5mA, IOH = -5mA and IOL = 2mA, IOH = -2mA) • 2 different CMOS hysteresis inputs with input shutdown function * • Automotive input with input shutdown function • TTL input with input shutdown function * • Programmable pull-up resistor: 50kΩ approx. • Analog input Note: MB96F345Dyy or MB96F345Fyy: Only Automotive input and CMOS hysteresis input (0.7/0.3) are supported Pout Nout R Standby control for input shutdown Standby control for input shutdown Standby control for input shutdown Standby control for input shutdown Hysteresis input Hysteresis input Automotive input TTL input Analog input N pull-up control Pout • CMOS level output (IOL = 3mA, IOH = -3mA) • 2 different CMOS hysteresis inputs with input shutdown function * • Automotive input with input shutdown function • TTL input with input shutdown function * • Programmable pull-up resistor: 50kΩ approx. *1: N-channel transistor has slew rate control according to I2C spec, irrespective of usage Nout *1 R Standby control for input shutdown Standby control for input shutdown Standby control for input shutdown Standby control for input shutdown Hysteresis input Hysteresis input Note: MB96F345Dyy or MB96F345Fyy: Only Automotive input and CMOS hysteresis input (0.7/0.3) are supported Automotive input TTL input 16 FME-MB96340 rev 10 MB96340 Series ■ MEMORY MAP MB96V300B FF:FFFFH MB96(F)34x Emulation ROM DE:0000H USER ROM / External Bus*4 External Bus External Bus 10:0000H 0F:E000H Boot-ROM Reserved 0F:0000H Boot-ROM Reserved DATA FLASH / Reserved*4 0C:0000H 0E:0000H External RAM Reserved 02:0000H Internal RAM bank 1 01:0000H RAMEND1*2 RAMSTART12 Reserved Internal RAM bank 1 Reserved ROM/RAM MIRROR Internal RAM bank 0 Reserved RAM availability depending on the device ROM/RAM MIRROR 00:8000H Internal RAM bank 0 RAMSTART0*3 00:0C00H RAMSTART0*2 External Bus end address*2 External Bus External Bus Peripherals Peripherals GPR*1 DMA External Bus Peripheral 00:0380H 00:0180H 00:0100H 00:00F0H 00:0000H GPR*1 DMA External Bus Peripheral *1: Unused GPR banks can be used as RAM area *2: For External Bus end address and RAMSTART/END addresses, please refer to the table on the next page. *3: For EVA device, RAMSTART0 depends on the configuration of the emulated device. *4: For details about USER ROM area or DATA FLASH area, see the ■ USER ROM MEMORY MAP FOR FLASH DEVICES and ■ USER ROM MEMORY MAP FOR MASK ROM DEVICES on the following pages. The External Bus area and DMA area are only available if the device contains the corresponding resource. The available RAM and ROM area depends on the device. FME-MB96340 rev 10 17 MB96340 Series ■ RAMSTART/END AND EXTERNAL BUS END ADDRESSES Devices MB96(F)345 MB96(F)346, MB96F347 MB96F348 Bank 0 Bank 1 External Bus RAM size RAM size end address 8KByte 16KByte 24KByte 00:21FFH 00:21FFH 00:21FFH RAMSTART0 00:6240H 00:4240H 00:2240H RAMSTART1 RAMEND1 - 18 FME-MB96340 rev 10 MB96340 Series ■ USER ROM MEMORY MAP FOR FLASH DEVICES MB96F345D MB96F345F Alternative mode CPU address FF:FFFFH FF:0000H FE:FFFFH FE:0000H FD:FFFFH FD:0000H FC:FFFFH FC:0000H FB:FFFFH FB:0000H FA:FFFFH FA:0000H F9:FFFFH F9:0000H F8:FFFFH F8:0000H F7:FFFFH F7:0000H F6:FFFFH F6:0000H F5:FFFFH F5:0000H F4:FFFFH F4:0000H F3:FFFFH F3:0000H F2:FFFFH F2:0000H F1:FFFFH F1:0000H F0:FFFFH F0:0000H E0:FFFFH Flash memory mode address 3F:FFFFH 3F:0000H 3E:FFFFH 3E:0000H 3D:FFFFH 3D:0000H 3C:FFFFH 3C:0000H 3B:FFFFH 3B:0000H 3A:FFFFH 3A:0000H 39:FFFFH 39:0000H 38:FFFFH 38:0000H 37:FFFFH 37:0000H 36:FFFFH 36:0000H 35:FFFFH 35:0000H 34:FFFFH 34:0000H 33:FFFFH 33:0000H 32:FFFFH 32:0000H 31:FFFFH 31:0000H 30:FFFFH 30:0000H Flash size 160kByte +64KByte Data Flash S39 - 64K S38 - 64K Flash A External bus E0:0000H DF:FFFFH DF:8000H DF:7FFFH DF:6000H DF:5FFFH DF:4000H DF:3FFFH DF:2000H DF:1FFFH DF:0000H DE:FFFFH DE:0000H Reserved 1F:7FFFH 1F:6000H 1F:5FFFH 1F:4000H 1F:3FFFH 1F:2000H 1F:1FFFH 1F:0000H SA3 - 8K SA2 - 8K SA1 - 8K SA0 - 8K *1 Reserved Flash A 0E:FFFFH 0E:FF00H 0E:FEFFH 0E:0000H 0D:FFFFH 0D:C000H 0D:BFFFH 0D:8000H 0D:7FFFH 0D:4000H 0D:3FFFH 0D:0000H 0C:FFFFH 0C:0000H (0E:FFFFH) (0E:FF00H) (0F:FFFFH) (0F:C000H) (0F:BFFFH) (0F:8000H) (0F:7FFFH) (0F:4000H) (0F:3FFFH) (0F:0000H) SDA0-256 *2 Reserved SDA4-16K SDA3-16K SDA2-16K SDA1-16K Reserved Data Flash A Data Flash A *1: Sector SA0 contains the ROM Configuration Block RCBA at CPU address DF:0000H - DF:007FH *2: Sector SDA0 contains the ROM Configuration Block RCBDA at CPU address DE:FF00H - DE:FF2FH FME-MB96340 rev 10 19 MB96340 Series MB96F346Y MB96F346R MB96F346A Alternative mode CPU address FF:FFFFH FF:0000H FE:FFFFH FE:0000H FD:FFFFH FD:0000H FC:FFFFH FC:0000H FB:FFFFH FB:0000H FA:FFFFH FA:0000H F9:FFFFH F9:0000H F8:FFFFH F8:0000H F7:FFFFH F7:0000H F6:FFFFH F6:0000H F5:FFFFH F5:0000H F4:FFFFH F4:0000H F3:FFFFH F3:0000H F2:FFFFH F2:0000H F1:FFFFH F1:0000H F0:FFFFH F0:0000H E0:FFFFH MB96F347Y MB96F347R MB96F347A Flash size 416kByte Flash memory mode address 3F:FFFFH 3F:0000H 3E:FFFFH 3E:0000H 3D:FFFFH 3D:0000H 3C:FFFFH 3C:0000H 3B:FFFFH 3B:0000H 3A:FFFFH 3A:0000H 39:FFFFH 39:0000H 38:FFFFH 38:0000H 37:FFFFH 37:0000H 36:FFFFH 36:0000H 35:FFFFH 35:0000H 34:FFFFH 34:0000H 33:FFFFH 33:0000H 32:FFFFH 32:0000H 31:FFFFH 31:0000H 30:FFFFH 30:0000H Flash size 288kByte S39 - 64K S38 - 64K S37 - 64K S36 - 64K S39 - 64K S38 - 64K S37 - 64K S36 - 64K S35 - 64K S34 - 64K Flash A External bus External bus E0:0000H DF:FFFFH DF:8000H DF:7FFFH DF:6000H DF:5FFFH DF:4000H DF:3FFFH DF:2000H DF:1FFFH DF:0000H DE:FFFFH DE:0000H Reserved 1F:7FFFH 1F:6000H 1F:5FFFH 1F:4000H 1F:3FFFH 1F:2000H 1F:1FFFH 1F:0000H Reserved SA3 - 8K SA2 - 8K SA1 - 8K SA0 - 8K *1 Reserved SA3 - 8K SA2 - 8K SA1 - 8K SA0 - 8K *1 Reserved Flash A *1: Sector SA0 contains the ROM Configuration Block RCBA at CPU address DF:0000H - DF:007FH 20 FME-MB96340 rev 10 MB96340 Series MB96F348Y MB96F348R MB96F348A Alternative mode CPU address FF:FFFFH FF:0000H FE:FFFFH FE:0000H FD:FFFFH FD:0000H FC:FFFFH FC:0000H FB:FFFFH FB:0000H FA:FFFFH FA:0000H F9:FFFFH F9:0000H F8:FFFFH F8:0000H F7:FFFFH F7:0000H F6:FFFFH F6:0000H F5:FFFFH F5:0000H F4:FFFFH F4:0000H F3:FFFFH F3:0000H F2:FFFFH F2:0000H F1:FFFFH F1:0000H F0:FFFFH F0:0000H E0:FFFFH MB96F348T MB96F348H MB96F348C Flash size 576kByte Flash memory mode address 3F:FFFFH 3F:0000H 3E:FFFFH 3E:0000H 3D:FFFFH 3D:0000H 3C:FFFFH 3C:0000H 3B:FFFFH 3B:0000H 3A:FFFFH 3A:0000H 39:FFFFH 39:0000H 38:FFFFH 38:0000H 37:FFFFH 37:0000H 36:FFFFH 36:0000H 35:FFFFH 35:0000H 34:FFFFH 34:0000H 33:FFFFH 33:0000H 32:FFFFH 32:0000H 31:FFFFH 31:0000H 30:FFFFH 30:0000H Flash size 544kByte S39 - 64K S38 - 64K S37 - 64K S36 - 64K S35 - 64K S34 - 64K S33 - 64K S32 - 64K S39 - 64K S38 - 64K S37 - 64K S36 - 64K S35 - 64K S34 - 64K S33 - 64K S32 - 64K Flash A External bus External bus E0:0000H DF:FFFFH DF:8000H DF:7FFFH DF:6000H DF:5FFFH DF:4000H DF:3FFFH DF:2000H DF:1FFFH DF:0000H DE:FFFFH DE:8000H DE:7FFFH DE:6000H DE:5FFFH DE:4000H DE:3FFFH DE:2000H DE:1FFFH DE:0000H Reserved 1F:7FFFH 1F:6000H 1F:5FFFH 1F:4000H 1F:3FFFH 1F:2000H 1F:1FFFH 1F:0000H Reserved SA3 - 8K SA2 - 8K SA1 - 8K SA0 - 8K *1 Reserved SA3 - 8K SA2 - 8K SA1 - 8K SA0 - 8K *1 Flash A 1E:7FFFH 1E:6000H 1E:5FFFH 1E:4000H 1E:3FFFH 1E:2000H 1E:1FFFH 1E:0000H Reserved SB3 - 8K SB2 - 8K SB1 - 8K SB0 - 8K *2 Flash B *1: Sector SA0 contains the ROM Configuration Block RCBA at CPU address DF:0000H - DF:007FH *2: Sector SB0 contains the ROM Configuration Block RCBB at CPU address DE:0000H - DE:002FH FME-MB96340 rev 10 21 MB96340 Series ■ USER ROM MEMORY MAP FOR MASK ROM DEVICES MB96345 CPU address FF:FFFFH FF:0000H FE:FFFFH FE:0000H FD:FFFFH FD:0000H FC:FFFFH FC:0000H FB:FFFFH MB96346 ROM size 288kByte ROM size 160kByte 128K ROM 256K ROM Reserved External bus E0:0000H DF:FFFFH DF:8000H DF:7FFFH External bus Reserved 32K ROM ROM configuration block RCB Reserved 32K ROM DF:0080H DF:007FH DF:0000H DE:FFFFH DE:0000H ROM configuration block RCB Reserved Reserved 22 FME-MB96340 rev 10 MB96340 Series ■ SERIAL PROGRAMMING COMMUNICATION INTERFACE USART pins for Flash serial programming (MD[2:0] = 010, Serial Communication mode) MB96F34x Pin number LQFP-100 57 58 59 60 61 62 22 23 24 85 86 87 Pin number USART Number QFP-100 59 60 61 62 63 64 24 25 26 87 88 89 USART3 USART2 USART1 USART0 SIN0 SOT0 SCK0 SIN1 SOT1 SCK1 SIN2 SOT2 SCK2 SIN3 SOT3 SCK3 Normal function Note: If a Flash programmer and its software needs to use a handshaking pin, Fujitsu suggests to the tool vendor to support at least port P00_1 on pin 76/78. If handshaking is used by the tool but P00_1 is not available in customer’s application, Fujitsu suggests to the customer to check the tool manual or to contact the tool vendor for alternative handshaking pins. FME-MB96340 rev 10 23 MB96340 Series ■ I/O MAP I/O map MB96(F)34x (1 of 30) Address 000000H 000001H 000002H 000003H 000004H 000005H 000006H 000007H 000008H 000009H 00000AH 00000BH000017H 000018H 000019H 00001AH 00001BH 00001CH 00001DH 00001EH 00001FH 000020H 000021H 000022H 000023H 000024H 000025H Register I/O Port P00 - Port Data Register I/O Port P01 - Port Data Register I/O Port P02 - Port Data Register I/O Port P03 - Port Data Register I/O Port P04 - Port Data Register I/O Port P05 - Port Data Register I/O Port P06 - Port Data Register I/O Port P07 - Port Data Register I/O Port P08 - Port Data Register I/O Port P09 - Port Data Register I/O Port P10 - Port Data Register Reserved ADC0 - Control Status register Low ADC0 - Control Status register High ADC0 - Data Register Low ADC0 - Data Register High ADC0 - Setting Register ADC0 - Setting Register ADC0 - Extended Configuration Register Reserved FRT0 - Data register of free-running timer FRT0 - Data register of free-running timer FRT0 - Control status register of free-running timer Low FRT0 - Control status register of free-running timer High FRT1 - Data register of free-running timer FRT1 - Data register of free-running timer TCCSL0 TCCSH0 TCDT1 TCCS0 TCDT0 ADECR ADCSL ADCSH ADCRL ADCRH ADSR ADCR ADCS Abbreviation 8-bit access PDR00 PDR01 PDR02 PDR03 PDR04 PDR05 PDR06 PDR07 PDR08 PDR09 PDR10 Abbreviation 16-bit access Access R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R R R/W R/W R/W R/W R/W R/W R/W R/W R/W 24 FME-MB96340 rev 10 MB96340 Series I/O map MB96(F)34x (2 of 30) Address 000026H 000027H 000028H 000029H 00002AH 00002BH 00002CH 00002DH 00002EH 00002FH 000030H 000031H 000032H 000033H 000034H 000035H 000036H 000037H 000038H 000039H 00003AH 00003BH 00003CH 00003DH 00003EH 00003FH 000040H 000041H 000042H Register FRT1 - Control status register of free-running timer Low FRT1 - Control status register of free-running timer High OCU0 - Output Compare Control Status OCU1 - Output Compare Control Status OCU0 - Compare Register OCU0 - Compare Register OCU1 - Compare Register OCU1 - Compare Register OCU2 - Output Compare Control Status OCU3 - Output Compare Control Status OCU2 - Compare Register OCU2 - Compare Register OCU3 - Compare Register OCU3 - Compare Register OCU4 - Output Compare Control Status OCU5 - Output Compare Control Status OCU4 - Compare Register OCU4 - Compare Register OCU5 - Compare Register OCU5 - Compare Register OCU6 - Output Compare Control Status OCU7 - Output Compare Control Status OCU6 - Compare Register OCU6 - Compare Register OCU7 - Compare Register OCU7 - Compare Register ICU0/ICU1 - Control Status Register ICU0/ICU1 - Edge register ICU0 - Capture Register Low ICS01 ICE01 IPCPL0 IPCP0 OCCP7 OCS6 OCS7 OCCP6 OCCP5 OCS4 OCS5 OCCP4 OCCP3 OCS2 OCS3 OCCP2 OCCP1 Abbreviation 8-bit access TCCSL1 TCCSH1 OCS0 OCS1 OCCP0 Abbreviation 16-bit access TCCS1 Access R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R FME-MB96340 rev 10 25 MB96340 Series I/O map MB96(F)34x (3 of 30) Address 000043H 000044H 000045H 000046H 000047H 000048H 000049H 00004AH 00004BH 00004CH 00004DH 00004EH 00004FH 000050H 000051H 000052H 000053H 000054H 000055H 000056H 000057H 000058H 000059H 00005AH 00005BH 00005CH 00005DH 00005EH 00005FH Register ICU0 - Capture Register High ICU1 - Capture Register Low ICU1 - Capture Register High ICU2/ICU3 - Control Status Register ICU2/ICU3 - Edge register ICU2 - Capture Register Low ICU2 - Capture Register High ICU3 - Capture Register Low ICU3 - Capture Register High ICU4/ICU5 - Control Status Register ICU4/ICU5 - Edge register ICU4 - Capture Register Low ICU4 - Capture Register High ICU5 - Capture Register Low ICU5 - Capture Register High ICU6/ICU7 - Control Status Register ICU6/ICU7 - Edge register ICU6 - Capture Register Low ICU6 - Capture Register High ICU7 - Capture Register Low ICU7 - Capture Register High EXTINT0 - External Interrupt Enable Register EXTINT0 - External Interrupt Interrupt request Register EXTINT0 - External Interrupt Level Select Low EXTINT0 - External Interrupt Level Select High EXTINT1 - External Interrupt Enable Register EXTINT1 - External Interrupt Interrupt request Register EXTINT1 - External Interrupt Level Select Low EXTINT1 - External Interrupt Level Select High Abbreviation 8-bit access IPCPH0 IPCPL1 IPCPH1 ICS23 ICE23 IPCPL2 IPCPH2 IPCPL3 IPCPH3 ICS45 ICE45 IPCPL4 IPCPH4 IPCPL5 IPCPH5 ICS67 ICE67 IPCPL6 IPCPH6 IPCPL7 IPCPH7 ENIR0 EIRR0 ELVRL0 ELVRH0 ENIR1 EIRR1 ELVRL1 ELVRH1 ELVR1 ELVR0 IPCP7 IPCP6 IPCP5 IPCP4 IPCP3 IPCP2 IPCP1 Abbreviation 16-bit access Access R R R R/W R/W R R R R R/W R/W R R R R R/W R/W R R R R R/W R/W R/W R/W R/W R/W R/W R/W 26 FME-MB96340 rev 10 MB96340 Series I/O map MB96(F)34x (4 of 30) Address 000060H 000061H 000062H 000062H 000063H 000063H 000064H 000065H 000066H 000066H 000067H 000067H 000068H 000069H 00006AH 00006AH 00006BH 00006BH 00006CH 00006DH 00006EH 00006EH 00006FH 00006FH 000070H 000071H 000072H Register RLT0 - Timer Control Status Register Low RLT0 - Timer Control Status Register High RLT0 - Reload Register - for writing RLT0 - Reload Register - for reading RLT0 - Reload Register - for writing RLT0 - Reload Register - for reading RLT1 - Timer Control Status Register Low RLT1 - Timer Control Status Register High RLT1 - Reload Register - for writing RLT1 - Reload Register - for reading RLT1 - Reload Register - for writing RLT1 - Reload Register - for reading RLT2 - Timer Control Status Register Low RLT2 - Timer Control Status Register High RLT2 - Reload Register - for writing RLT2 - Reload Register - for reading RLT2 - Reload Register - for writing RLT2 - Reload Register - for reading RLT3 - Timer Control Status Register Low RLT3 - Timer Control Status Register High RLT3 - Reload Register - for writing RLT3 - Reload Register - for reading RLT3 - Reload Register - for writing RLT3 - Reload Register - for reading RLT6 - Timer Control Status Register Low (dedic. RLT for PPG) RLT6 - Timer Control Status Register High (dedic. RLT for PPG) RLT6 - Reload Register (dedic. RLT for PPG) - for writing TMCSRL6 TMCSRH6 TMRLR6 TMCSR6 TMCSRL3 TMCSRH3 TMRLR3 TMR3 TMCSR3 TMCSRL2 TMCSRH2 TMRLR2 TMR2 TMCSR2 TMCSRL1 TMCSRH1 TMRLR1 TMR1 TMCSR1 Abbreviation 8-bit access TMCSRL0 TMCSRH0 TMRLR0 TMR0 Abbreviation 16-bit access TMCSR0 Access R/W R/W W R W R R/W R/W W R W R R/W R/W W R W R R/W R/W W R W R R/W R/W W FME-MB96340 rev 10 27 MB96340 Series I/O map MB96(F)34x (5 of 30) Address 000072H 000073H 000073H 000074H 000075H 000076H 000077H 000078H 000079H 00007AH 00007BH 00007CH 00007DH 00007EH 00007FH 000080H 000081H 000082H 000083H 000084H 000085H 000086H 000087H 000088H 000089H 00008AH 00008BH 00008CH Register RLT6 - Reload Register (dedic. RLT for PPG) - for reading RLT6 - Reload Register (dedic. RLT for PPG) - for writing RLT6 - Reload Register (dedic. RLT for PPG) - for reading PPG3-PPG0 - General Control register 1 Low PPG3-PPG0 - General Control register 1 High PPG3-PPG0 - General Control register 2 Low PPG3-PPG0 - General Control register 2 High PPG0 - Timer register PPG0 - Timer register PPG0 - Period setting register PPG0 - Period setting register PPG0 - Duty cycle register PPG0 - Duty cycle register PPG0 - Control status register Low PPG0 - Control status register High PPG1 - Timer register PPG1 - Timer register PPG1 - Period setting register PPG1 - Period setting register PPG1 - Duty cycle register PPG1 - Duty cycle register PPG1 - Control status register Low PPG1 - Control status register High PPG2 - Timer register PPG2 - Timer register PPG2 - Period setting register PPG2 - Period setting register PPG2 - Duty cycle register PDUT2 PCSR2 PCNL1 PCNH1 PTMR2 PCN1 PDUT1 PCSR1 PCNL0 PCNH0 PTMR1 PCN0 PDUT0 PCSR0 GCN1L0 GCN1H0 GCN2L0 GCN2H0 PTMR0 GCN20 GCN10 Abbreviation 8-bit access Abbreviation 16-bit access TMR6 Access R W R R/W R/W R/W R/W R R W W W W R/W R/W R R W W W W R/W R/W R R W W W 28 FME-MB96340 rev 10 MB96340 Series I/O map MB96(F)34x (6 of 30) Address 00008DH 00008EH 00008FH 000090H 000091H 000092H 000093H 000094H 000095H 000096H 000097H 000098H 000099H 00009AH 00009BH 00009CH 00009DH 00009EH 00009FH 0000A0H 0000A1H 0000A2H 0000A3H 0000A4H 0000A5H 0000A6H 0000A7H 0000A8H 0000A9H 0000AAH Register PPG2 - Duty cycle register PPG2 - Control status register Low PPG2 - Control status register High PPG3 - Timer register PPG3 - Timer register PPG3 - Period setting register PPG3 - Period setting register PPG3 - Duty cycle register PPG3 - Duty cycle register PPG3 - Control status register Low PPG3 - Control status register High PPG7-PPG4 - General Control register 1 Low PPG7-PPG4 - General Control register 1 High PPG7-PPG4 - General Control register 2 Low PPG7-PPG4 - General Control register 2 High PPG4 - Timer register PPG4 - Timer register PPG4 - Period setting register PPG4 - Period setting register PPG4 - Duty cycle register PPG4 - Duty cycle register PPG4 - Control status register Low PPG4 - Control status register High PPG5 - Timer register PPG5 - Timer register PPG5 - Period setting register PPG5 - Period setting register PPG5 - Duty cycle register PPG5 - Duty cycle register PPG5 - Control status register Low PCNL5 PCN5 PDUT5 PCSR5 PCNL4 PCNH4 PTMR5 PCN4 PDUT4 PCSR4 PCNL3 PCNH3 GCN1L1 GCN1H1 GCN2L1 GCN2H1 PTMR4 GCN21 GCN11 PCN3 PDUT3 PCSR3 PCNL2 PCNH2 PTMR3 PCN2 Abbreviation 8-bit access Abbreviation 16-bit access Access W R/W R/W R R W W W W R/W R/W R/W R/W R/W R/W R R W W W W R/W R/W R R W W W W R/W FME-MB96340 rev 10 29 MB96340 Series I/O map MB96(F)34x (7 of 30) Address 0000ABH 0000ACH 0000ADH 0000AEH 0000AFH 0000B0H 0000B1H 0000B2H 0000B3H 0000B4H 0000B5H 0000B6H 0000B7H 0000B8H 0000B9H 0000BAH 0000BBH 0000BCH 0000BDH 0000BEH 0000BFH 0000C0H 0000C1H 0000C2H 0000C2H 0000C3H 0000C4H 0000C5H 0000C6H 0000C7H Register PPG5 - Control status register High I2C0 - Bus Status Register I2C0 - Bus Control Register I2C0 - Ten bit Slave address Register Low I2C0 - Ten bit Slave address Register High I2C0 - Ten bit Address mask Register Low I2C0 - Ten bit Address mask Register High I2C0 - Seven bit Slave address Register I2C0 - Seven bit Address mask Register I2C0 - Data Register I2C0 - Clock Control Register I2C1 - Bus Status Register I2C1 - Bus Control Register I2C1 - Ten bit Slave address Register Low I2C1 - Ten bit Slave address Register High I2C1 - Ten bit Address mask Register Low I2C1 - Ten bit Address mask Register High I2C1 - Seven bit Slave address Register I2C1 - Seven bit Address mask Register I2C1 - Data Register I2C1 - Clock Control Register USART0 - Serial Mode Register USART0 - Serial Control Register USART0 - TX Register USART0 - RX Register USART0 - Serial Status USART0 - Control/Com. Register USART0 - Ext. Status Register USART0 - Baud Rate Generator Register Low USART0 - Baud Rate Generator Register High Abbreviation 8-bit access PCNH5 IBSR0 IBCR0 ITBAL0 ITBAH0 ITMKL0 ITMKH0 ISBA0 ISMK0 IDAR0 ICCR0 IBSR1 IBCR1 ITBAL1 ITBAH1 ITMKL1 ITMKH1 ISBA1 ISMK1 IDAR1 ICCR1 SMR0 SCR0 TDR0 RDR0 SSR0 ECCR0 ESCR0 BGRL0 BGRH0 BGR0 ITMK1 ITBA1 ITMK0 ITBA0 Abbreviation 16-bit access Access R/W R R/W R/W R/W R/W R/W R/W R/W R/W R/W R R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W W R R/W R/W R/W R/W R/W 30 FME-MB96340 rev 10 MB96340 Series I/O map MB96(F)34x (8 of 30) Address 0000C8H 0000C9H 0000CAH 0000CBH 0000CCH 0000CCH 0000CDH 0000CEH 0000CFH 0000D0H 0000D1H 0000D2H 0000D3H 0000D4H 0000D5H 0000D6H 0000D6H 0000D7H 0000D8H 0000D9H 0000DAH 0000DBH 0000DCH 0000DDH 0000DEH 0000DFH 0000E0H 0000E0H 0000E1H 0000E2H Register USART0 - Extended Serial Interrupt Register Reserved USART1 - Serial Mode Register USART1 - Serial Control Register USART1 - TX Register USART1 - RX Register USART1 - Serial Status USART1 - Control/Com. Register USART1 - Ext. Status Register USART1 - Baud Rate Generator Register Low USART1 - Baud Rate Generator Register High USART1 - Extended Serial Interrupt Register Reserved USART2 - Serial Mode Register USART2 - Serial Control Register USART2 - TX Register USART2 - RX Register USART2 - Serial Status USART2 - Control/Com. Register USART2 - Ext. Status Register USART2 - Baud Rate Generator Register Low USART2 - Baud Rate Generator Register High USART2 - Extended Serial Interrupt Register Reserved USART3 - Serial Mode Register USART3 - Serial Control Register USART3 - TX Register USART3 - RX Register USART3 - Serial Status USART3 - Control/Com. Register SMR3 SCR3 TDR3 RDR3 SSR3 ECCR3 SMR2 SCR2 TDR2 RDR2 SSR2 ECCR2 ESCR2 BGRL2 BGRH2 ESIR2 BGR2 SMR1 SCR1 TDR1 RDR1 SSR1 ECCR1 ESCR1 BGRL1 BGRH1 ESIR1 BGR1 Abbreviation 8-bit access ESIR0 Abbreviation 16-bit access Access R/W R/W R/W W R R/W R/W R/W R/W R/W R/W R/W R/W W R R/W R/W R/W R/W R/W R/W R/W R/W W R R/W R/W FME-MB96340 rev 10 31 MB96340 Series I/O map MB96(F)34x (9 of 30) Address 0000E3H 0000E4H 0000E5H 0000E6H 0000E7H0000EFH 0000F0H0000FFH 000100H 000101H 000102H 000103H 000104H 000105H 000106H 000107H 000108H 000109H 00010AH 00010BH 00010CH 00010DH 00010EH 00010FH 000110H 000111H 000112H 000113H 000114H 000115H 000116H Register USART3 - Ext. Status Register USART3 - Baud Rate Generator Register Low USART3 - Baud Rate Generator Register High USART3 - Extended Serial Interrupt Register Reserved External Bus area DMA0 - Buffer address pointer low byte DMA0 - Buffer address pointer middle byte DMA0 - Buffer address pointer high byte DMA0 - DMA control register DMA0 - I/O register address pointer low byte DMA0 - I/O register address pointer high byte DMA0 - Data counter low byte DMA0 - Data counter high byte DMA1 - Buffer address pointer low byte DMA1 - Buffer address pointer middle byte DMA1 - Buffer address pointer high byte DMA1 - DMA control register DMA1 - I/O register address pointer low byte DMA1 - I/O register address pointer high byte DMA1 - Data counter low byte DMA1 - Data counter high byte DMA2 - Buffer address pointer low byte DMA2 - Buffer address pointer middle byte DMA2 - Buffer address pointer high byte DMA2 - DMA control register DMA2 - I/O register address pointer low byte DMA2 - I/O register address pointer high byte DMA2 - Data counter low byte EXTBUS0 BAPL0 BAPM0 BAPH0 DMACS0 IOAL0 IOAH0 DCTL0 DCTH0 BAPL1 BAPM1 BAPH1 DMACS1 IOAL1 IOAH1 DCTL1 DCTH1 BAPL2 BAPM2 BAPH2 DMACS2 IOAL2 IOAH2 DCTL2 DCT2 IOA2 DCT1 IOA1 DCT0 IOA0 Abbreviation 8-bit access ESCR3 BGRL3 BGRH3 ESIR3 BGR3 Abbreviation 16-bit access Access R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W 32 FME-MB96340 rev 10 MB96340 Series I/O map MB96(F)34x (10 of 30) Address 000117H 000118H 000119H 00011AH 00011BH 00011CH 00011DH 00011EH 00011FH 000120H 000121H 000122H 000123H 000124H 000125H 000126H 000127H 000128H 000129H 00012AH 00012BH 00012CH 00012DH 00012EH 00012FH 000130H00017FH 000180H00037FH 000380H 000381H Register DMA2 - Data counter high byte DMA3 - Buffer address pointer low byte DMA3 - Buffer address pointer middle byte DMA3 - Buffer address pointer high byte DMA3 - DMA control register DMA3 - I/O register address pointer low byte DMA3 - I/O register address pointer high byte DMA3 - Data counter low byte DMA3 - Data counter high byte DMA4 - Buffer address pointer low byte DMA4 - Buffer address pointer middle byte DMA4 - Buffer address pointer high byte DMA4 - DMA control register DMA4 - I/O register address pointer low byte DMA4 - I/O register address pointer high byte DMA4 - Data counter low byte DMA4 - Data counter high byte DMA5 - Buffer address pointer low byte DMA5 - Buffer address pointer middle byte DMA5 - Buffer address pointer high byte DMA5 - DMA control register DMA5 - I/O register address pointer low byte DMA5 - I/O register address pointer high byte DMA5 - Data counter low byte DMA5 - Data counter high byte Reserved CPU - General Purpose registers (RAM access) DMA0 - Interrupt select DMA1 - Interrupt select GPR_RAM DISEL0 DISEL1 Abbreviation 8-bit access DCTH2 BAPL3 BAPM3 BAPH3 DMACS3 IOAL3 IOAH3 DCTL3 DCTH3 BAPL4 BAPM4 BAPH4 DMACS4 IOAL4 IOAH4 DCTL4 DCTH4 BAPL5 BAPM5 BAPH5 DMACS5 IOAL5 IOAH5 DCTL5 DCTH5 DCT5 IOA5 DCT4 IOA4 DCT3 IOA3 Abbreviation 16-bit access Access R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W FME-MB96340 rev 10 33 MB96340 Series I/O map MB96(F)34x (11 of 30) Address 000382H 000383H 000384H 000385H 000386H00038FH 000390H 000391H 000392H 000393H 000394H 000395H 000396H00039FH 0003A0H 0003A1H 0003A2H 0003A3H 0003A4H 0003A5H 0003A6H0003ABH 0003ACH 0003ADH 0003AEH 0003AFH 0003B0H 0003B1H 0003B2H 0003B3H 0003B4H Register DMA2 - Interrupt select DMA3 - Interrupt select DMA4 - Interrupt select DMA5 - Interrupt select Reserved DMA - Status register low byte DMA - Status register high byte DMA - Stop status register low byte DMA - Stop status register high byte DMA - Enable register low byte DMA - Enable register high byte Reserved Interrupt level register Interrupt index register Interrupt vector table base register Low Interrupt vector table base register High Delayed Interrupt register Non Maskable Interrupt register Reserved EDSU communication interrupt selection Low EDSU communication interrupt selection High ROM mirror control register EDSU configuration register Memory patch control/status register ch 0/1 Memory patch control/status register ch 0/1 Memory patch control/status register ch 2/3 Memory patch control/status register ch 2/3 Memory patch control/status register ch 4/5 PFCS2 PFCS1 EDSU2L EDSU2H ROMM EDSU PFCS0 EDSU2 ILR IDX TBRL TBRH DIRR NMI TBR ICR DSRL DSRH DSSRL DSSRH DERL DERH DER DSSR DSR Abbreviation 8-bit access DISEL2 DISEL3 DISEL4 DISEL5 Abbreviation 16-bit access Access R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W 34 FME-MB96340 rev 10 MB96340 Series I/O map MB96(F)34x (12 of 30) Address 0003B5H 0003B6H 0003B7H 0003B8H 0003B9H 0003BAH 0003BBH 0003BCH 0003BDH 0003BEH 0003BFH 0003C0H 0003C1H 0003C2H 0003C3H 0003C4H 0003C5H 0003C6H 0003C7H 0003C8H 0003C9H 0003CAH 0003CBH 0003CCH 0003CDH 0003CEH 0003CFH 0003D0H 0003D1H 0003D2H Register Memory patch control/status register ch 4/5 Memory patch control/status register ch 6/7 Memory patch control/status register ch 6/7 Memory Patch function - Patch address 0 low Memory Patch function - Patch address 0 middle Memory Patch function - Patch address 0 high Memory Patch function - Patch address 1 low Memory Patch function - Patch address 1 middle Memory Patch function - Patch address 1 high Memory Patch function - Patch address 2 low Memory Patch function - Patch address 2 middle Memory Patch function - Patch address 2 high Memory Patch function - Patch address 3 low Memory Patch function - Patch address 3 middle Memory Patch function - Patch address 3 high Memory Patch function - Patch address 4 low Memory Patch function - Patch address 4 middle Memory Patch function - Patch address 4 high Memory Patch function - Patch address 5 low Memory Patch function - Patch address 5 middle Memory Patch function - Patch address 5 high Memory Patch function - Patch address 6 low Memory Patch function - Patch address 6 middle Memory Patch function - Patch address 6 high Memory Patch function - Patch address 7 low Memory Patch function - Patch address 7 middle Memory Patch function - Patch address 7 high Memory Patch function - Patch data 0 Low Memory Patch function - Patch data 0 High Memory Patch function - Patch data 1 Low PFAL0 PFAM0 PFAH0 PFAL1 PFAM1 PFAH1 PFAL2 PFAM2 PFAH2 PFAL3 PFAM3 PFAH3 PFAL4 PFAM4 PFAH4 PFAL5 PFAM5 PFAH5 PFAL6 PFAM6 PFAH6 PFAL7 PFAM7 PFAH7 PFDL0 PFDH0 PFDL1 PFD1 PFD0 PFCS3 Abbreviation 8-bit access Abbreviation 16-bit access Access R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W FME-MB96340 rev 10 35 MB96340 Series I/O map MB96(F)34x (13 of 30) Address 0003D3H 0003D4H 0003D5H 0003D6H 0003D7H 0003D8H 0003D9H 0003DAH 0003DBH 0003DCH 0003DDH 0003DEH 0003DFH 0003E0H 0003E1H 0003E2H 0003E3H0003F0H 0003F1H 0003F2H 0003F3H 0003F4H 0003F5H 0003F6H 0003F7H 0003F8H 0003F9H 0003FAH 0003FBH Register Memory Patch function - Patch data 1 High Memory Patch function - Patch data 2 Low Memory Patch function - Patch data 2 High Memory Patch function - Patch data 3 Low Memory Patch function - Patch data 3 High Memory Patch function - Patch data 4 Low Memory Patch function - Patch data 4 High Memory Patch function - Patch data 5 Low Memory Patch function - Patch data 5 High Memory Patch function - Patch data 6 Low Memory Patch function - Patch data 6 High Memory Patch function - Patch data 7 Low Memory Patch function - Patch data 7 High Data Flash Control and Status register A Data Flash Write command sequencer Control register A Data Flash Write command sequencer Status register A Reserved Memory Control Status Register A Memory Timing Configuration Register A Low Memory Timing Configuration Register A High Reserved Memory Control Status Register B Memory Timing Configuration Register B Low Memory Timing Configuration Register B High Flash Memory Write Control register 0 Flash Memory Write Control register 1 Flash Memory Write Control register 2 Flash Memory Write Control register 3 MCSRB MTCRBL MTCRBH FMWC0 FMWC1 FMWC2 FMWC3 MTCRB MCSRA MTCRAL MTCRAH MTCRA Abbreviation 8-bit access PFDH1 PFDL2 PFDH2 PFDL3 PFDH3 PFDL4 PFDH4 PFDL5 PFDH5 PFDL6 PFDH6 PFDL7 PFDH7 DFCSA DFWCA DFWSA PFD7 PFD6 PFD5 PFD4 PFD3 PFD2 Abbreviation 16-bit access Access R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W 36 FME-MB96340 rev 10 MB96340 Series I/O map MB96(F)34x (14 of 30) Address 0003FCH 0003FDH 0003FEH0003FFH 000400H 000401H 000402H 000403H 000404H 000405H 000406H 000407H 000408H 000409H 00040AH 00040BH 00040CH 00040DH 00040EH 00040FH 000410H000414H 000415H 000416H 000417H 000418H 000419H 00041AH 00041BH Register Flash Memory Write Control register 4 Flash Memory Write Control register 5 Reserved Standby Mode control register Clock select register Clock Stabilization select register Clock monitor register Clock Frequency control register Low Clock Frequency control register High PLL Control register Low PLL Control register High RC clock timer control register Main clock timer control register Sub clock timer control register Reset cause and clock status register with clear function Reset configuration register Reset cause and clock status register Watch dog timer configuration register Watch dog timer clear pattern register Reserved Clock output activation register Clock output configuration register 0 Clock output configuration register 1 Clock Modulator control register Reserved Clock Modulator Parameter register Low Clock Modulator Parameter register High CMPRL CMPRH CMPR COAR COCR0 COCR1 CMCR SMCR CKSR CKSSR CKMR CKFCRL CKFCRH PLLCRL PLLCRH RCTCR MCTCR SCTCR RCCSRC RCR RCCSR WDTC WDTCP PLLCR CKFCR Abbreviation 8-bit access FMWC4 FMWC5 Abbreviation 16-bit access Access R/W R/W R/W R/W R/W R R/W R/W R/W R/W R/W R/W R/W R R/W R R/W W R/W R/W R/W R/W R/W R/W FME-MB96340 rev 10 37 MB96340 Series I/O map MB96(F)34x (15 of 30) Address 00041CH00042BH 00042CH 00042DH 00042EH00042FH 000430H 000431H 000432H 000433H 000434H 000435H 000436H 000437H 000438H 000439H 00043AH 00043BH000443H 000444H 000445H 000446H 000447H 000448H 000449H 00044AH 00044BH 00044CH 00044DH 00044EH Reserved Voltage Regulator Control register Clock Input and LVD Control Register Reserved I/O Port P00 - Data Direction Register I/O Port P01 - Data Direction Register I/O Port P02 - Data Direction Register I/O Port P03 - Data Direction Register I/O Port P04 - Data Direction Register I/O Port P05 - Data Direction Register I/O Port P06 - Data Direction Register I/O Port P07 - Data Direction Register I/O Port P08 - Data Direction Register I/O Port P09 - Data Direction Register I/O Port P10 - Data Direction Register Reserved I/O Port P00 - Port Input Enable Register I/O Port P01 - Port Input Enable Register I/O Port P02 - Port Input Enable Register I/O Port P03 - Port Input Enable Register I/O Port P04 - Port Input Enable Register I/O Port P05 - Port Input Enable Register I/O Port P06 - Port Input Enable Register I/O Port P07 - Port Input Enable Register I/O Port P08 - Port Input Enable Register I/O Port P09 - Port Input Enable Register I/O Port P10 - Port Input Enable Register PIER00 PIER01 PIER02 PIER03 PIER04 PIER05 PIER06 PIER07 PIER08 PIER09 PIER10 DDR00 DDR01 DDR02 DDR03 DDR04 DDR05 DDR06 DDR07 DDR08 DDR09 DDR10 VRCR CILCR Register Abbreviation 8-bit access Abbreviation 16-bit access Access R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W 38 FME-MB96340 rev 10 MB96340 Series I/O map MB96(F)34x (16 of 30) Address 00044FH000457H 000458H 000459H 00045AH 00045BH 00045CH 00045DH 00045EH 00045FH 000460H 000461H 000462H 000463H00046BH 00046CH 00046DH 00046EH 00046FH 000470H 000471H 000472H 000473H 000474H 000475H 000476H 000477H00047FH 000480H 000481H 000482H Reserved I/O Port P00 - Port Input Level Register I/O Port P01 - Port Input Level Register I/O Port P02 - Port Input Level Register I/O Port P03 - Port Input Level Register I/O Port P04 - Port Input Level Register I/O Port P05 - Port Input Level Register I/O Port P06 - Port Input Level Register I/O Port P07 - Port Input Level Register I/O Port P08 - Port Input Level Register I/O Port P09 - Port Input Level Register I/O Port P10 - Port Input Level Register Reserved I/O Port P00 - Extended Port Input Level Register I/O Port P01 - Extended Port Input Level Register I/O Port P02 - Extended Port Input Level Register I/O Port P03 - Extended Port Input Level Register I/O Port P04 - Extended Port Input Level Register I/O Port P05 - Extended Port Input Level Register I/O Port P06 - Extended Port Input Level Register I/O Port P07 - Extended Port Input Level Register I/O Port P08 - Extended Port Input Level Register I/O Port P09 - Extended Port Input Level Register I/O Port P10 - Extended Port Input Level Register Reserved I/O Port P00 - Port Output Drive Register I/O Port P01 - Port Output Drive Register I/O Port P02 - Port Output Drive Register PODR00 PODR01 PODR02 EPILR00 EPILR01 EPILR02 EPILR03 EPILR04 EPILR05 EPILR06 EPILR07 EPILR08 EPILR09 EPILR10 PILR00 PILR01 PILR02 PILR03 PILR04 PILR05 PILR06 PILR07 PILR08 PILR09 PILR10 Register Abbreviation 8-bit access Abbreviation 16-bit access Access R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W FME-MB96340 rev 10 39 MB96340 Series I/O map MB96(F)34x (17 of 30) Address 000483H 000484H 000485H 000486H 000487H 000488H 000489H 00048AH 00048BH0004A7H 0004A8H 0004A9H 0004AAH 0004ABH 0004ACH 0004ADH 0004AEH 0004AFH 0004B0H 0004B1H 0004B2H 0004B3H0004BBH 0004BCH 0004BDH 0004BEH 0004BFH 0004C0H 0004C1H 0004C2H 0004C3H Register I/O Port P03 - Port Output Drive Register I/O Port P04 - Port Output Drive Register I/O Port P05 - Port Output Drive Register I/O Port P06 - Port Output Drive Register I/O Port P07 - Port Output Drive Register I/O Port P08 - Port Output Drive Register I/O Port P09 - Port Output Drive Register I/O Port P10 - Port Output Drive Register Reserved I/O Port P00 - Pull-Up resistor Control Register I/O Port P01 - Pull-Up resistor Control Register I/O Port P02 - Pull-Up resistor Control Register I/O Port P03 - Pull-Up resistor Control Register I/O Port P04 - Pull-Up resistor Control Register I/O Port P05 - Pull-Up resistor Control Register I/O Port P06 - Pull-Up resistor Control Register I/O Port P07 - Pull-Up resistor Control Register I/O Port P08 - Pull-Up resistor Control Register I/O Port P09 - Pull-Up resistor Control Register I/O Port P10 - Pull-Up resistor Control Register Reserved I/O Port P00 - External Pin State Register I/O Port P01 - External Pin State Register I/O Port P02 - External Pin State Register I/O Port P03 - External Pin State Register I/O Port P04 - External Pin State Register I/O Port P05 - External Pin State Register I/O Port P06 - External Pin State Register I/O Port P07 - External Pin State Register EPSR00 EPSR01 EPSR02 EPSR03 EPSR04 EPSR05 EPSR06 EPSR07 PUCR00 PUCR01 PUCR02 PUCR03 PUCR04 PUCR05 PUCR06 PUCR07 PUCR08 PUCR09 PUCR10 Abbreviation 8-bit access PODR03 PODR04 PODR05 PODR06 PODR07 PODR08 PODR09 PODR10 Abbreviation 16-bit access Access R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R R R R R R R R 40 FME-MB96340 rev 10 MB96340 Series I/O map MB96(F)34x (18 of 30) Address 0004C4H 0004C5H 0004C6H 0004C7H0004CFH 0004D0H 0004D1H 0004D2H 0004D3H 0004D4H 0004D5H 0004D6H 0004D7H 0004D8H 0004D9H 0004DAH 0004DBH 0004DCH 0004DDH 0004DEH 0004DFH 0004E0H 0004E1H 0004E2H 0004E3H 0004E4H 0004E5H 0004E6H 0004E7H 0004E8H Register I/O Port P08 - External Pin State Register I/O Port P09 - External Pin State Register I/O Port P10 - External Pin State Register Reserved ADC analog input enable register 0 ADC analog input enable register 1 ADC analog input enable register 2 ADC analog input enable register 3 ADC analog input enable register 4 Reserved Peripheral Resource Relocation Register 0 Peripheral Resource Relocation Register 1 Peripheral Resource Relocation Register 2 Peripheral Resource Relocation Register 3 Peripheral Resource Relocation Register 4 Peripheral Resource Relocation Register 5 Peripheral Resource Relocation Register 6 Peripheral Resource Relocation Register 7 Peripheral Resource Relocation Register 8 Peripheral Resource Relocation Register 9 RTC - Sub Second Register L RTC - Sub Second Register M RTC - Sub-Second Register H RTC - Second Register RTC - Minutes RTC - Hour RTC - Timer Control Extended Register RTC - Clock select register RTC - Timer Control Register Low PRRR0 PRRR1 PRRR2 PRRR3 PRRR4 PRRR5 PRRR6 PRRR7 PRRR8 PRRR9 WTBRL0 WTBRH0 WTBR1 WTSR WTMR WTHR WTCER WTCKSR WTCRL WTCR WTBR0 ADER0 ADER1 ADER2 ADER3 ADER4 Abbreviation 8-bit access EPSR08 EPSR09 EPSR10 Abbreviation 16-bit access Access R R R R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W FME-MB96340 rev 10 41 MB96340 Series I/O map MB96(F)34x (19 of 30) Address 0004E9H 0004EAH 0004EBH 0004ECH 0004EDH 0004EEH 0004EFH 0004F0H 0004F1H 0004F2H0004F9H 0004FAH 0004FBH00053DH 00053EH 00053FH 000540H 000540H 000541H 000542H 000543H 000544H 000545H 000546H 000547H 000548H 000549H 00054AH 00054AH 00054BH 00054CH Register RTC - Timer Control Register High CAL - Calibration unit Control register Reserved CAL - Duration Timer Data Register Low CAL - Duration Timer Data Register High CAL - Calibration Timer Register 2 Low CAL - Calibration Timer Register 2 High CAL - Calibration Timer Register 1 Low CAL - Calibration Timer Register 1 High Reserved RLT - Timer input select (for Cascading) Reserved USART7 - Serial Mode Register USART7 - Serial Control Register USART7 - Serial TX Register USART7 - Serial RX Register USART7 - Serial Status Register USART7 - Ext. Control/Com. Register USART7 - Ext. Status Com. Register USART7 - Baud Rate Generator Register Low USART7 - Baud Rate Generator Register High USART7 - Extended Serial Interrupt Register Reserved USART8 - Serial Mode Register USART8 - Serial Control Register USART8 - Serial TX Register USART8 - Serial RX Register USART8 - Serial Status Register USART8 - Ext. Control/Com. Register SMR8 SCR8 TDR8 RDR8 SSR8 ECCR8 SMR7 SCR7 TDR7 RDR7 SSR7 ECCR7 ESCR7 BGRL7 BGRH7 ESIR7 BGR7 TMISR CUTDL CUTDH CUTR2L CUTR2H CUTR1L CUTR1H CUTR1 CUTR2 CUTD Abbreviation 8-bit access WTCRH CUCR Abbreviation 16-bit access Access R/W R/W R/W R/W R R R R R/W R/W R/W W R R/W R/W R/W R/W R/W R/W R/W R/W W R R/W R/W 42 FME-MB96340 rev 10 MB96340 Series I/O map MB96(F)34x (20 of 30) Address 00054DH 00054EH 00054FH 000550H 000551H 000552H 000553H 000554H 000554H 000555H 000556H 000557H 000558H 000559H 00055AH 00055BH00055FH 000560H 000561H 000562H 000563H 000564H 000565H 000566H 000567H 000568H 000569H 00056AH 00056BH 00056CH Register USART8 - Ext. Status Com. Register USART8 - Baud Rate Generator Register Low USART8 - Baud Rate Generator Register High USART8 - Extended Serial Interrupt Register Reserved USART9 - Serial Mode Register USART9 - Serial Control Register USART9 - Serial TX Register USART9 - Serial RX Register USART9 - Serial Status Register USART9 - Ext. Control/Com. Register USART9 - Ext. Status Com. Register USART9 - Baud Rate Generator Register Low USART9 - Baud Rate Generator Register High USART9 - Extended Serial Interrupt Register Reserved ALARM0 - Control Status Register ALARM0 - Extended Control Status Register ALARM1 - Control Status Register ALARM1 - Extended Control Status Register PPG6 - Timer register PPG6 - Timer register PPG6 - Period setting register PPG6 - Period setting register PPG6 - Duty cycle register PPG6 - Duty cycle register PPG6 - Control status register Low PPG6 - Control status register High PPG7 - Timer register PCNL6 PCNH6 PTMR7 PCN6 PDUT6 PCSR6 ACSR0 AECSR0 ACSR1 AECSR1 PTMR6 SMR9 SCR9 TDR9 RDR9 SSR9 ECCR9 ESCR9 BGRL9 BGRH9 ESIR9 BGR9 Abbreviation 8-bit access ESCR8 BGRL8 BGRH8 ESIR8 BGR8 Abbreviation 16-bit access Access R/W R/W R/W R/W R/W R/W W R R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R R W W W W R/W R/W R FME-MB96340 rev 10 43 MB96340 Series I/O map MB96(F)34x (21 of 30) Address 00056DH 00056EH 00056FH 000570H 000571H 000572H 000573H 000574H 000575H 000576H 000577H 000578H 000579H 00057AH 00057BH 00057CH 00057DH 00057EH 00057FH 000580H 000581H 000582H 000583H 000584H 000585H 000586H 000587H 000588H 000589H 00058AH Register PPG7 - Timer register PPG7 - Period setting register PPG7 - Period setting register PPG7 - Duty cycle register PPG7 - Duty cycle register PPG7 - Control status register Low PPG7 - Control status register High PPG11-PPG8 - General Control register 1 Low PPG11-PPG8 - General Control register 1 High PPG11-PPG8 - General Control register 2 Low PPG11-PPG8 - General Control register 2 High PPG8 - Timer register PPG8 - Timer register PPG8 - Period setting register PPG8 - Period setting register PPG8 - Duty cycle register PPG8 - Duty cycle register PPG8 - Control status register Low PPG8 - Control status register High PPG9 - Timer register PPG9 - Timer register PPG9 - Period setting register PPG9 - Period setting register PPG9 - Duty cycle register PPG9 - Duty cycle register PPG9 - Control status register Low PPG9 - Control status register High PPG10 - Timer register PPG10 - Timer register PPG10 - Period setting register PCSR10 PCNL9 PCNH9 PTMR10 PCN9 PDUT9 PCSR9 PCNL8 PCNH8 PTMR9 PCN8 PDUT8 PCSR8 PCNL7 PCNH7 GCN1L2 GCN1H2 GCN2L2 GCN2H2 PTMR8 GCN22 GCN12 PCN7 PDUT7 PCSR7 Abbreviation 8-bit access Abbreviation 16-bit access Access R W W W W R/W R/W R/W R/W R/W R/W R R W W W W R/W R/W R R W W W W R/W R/W R R W 44 FME-MB96340 rev 10 MB96340 Series I/O map MB96(F)34x (22 of 30) Address 00058BH 00058CH 00058DH 00058EH 00058FH 000590H 000591H 000592H 000593H 000594H 000595H 000596H 000597H 000598H 000599H 00059AH 00059BH 00059CH 00059DH 00059EH 00059FH 0005A0H 0005A1H 0005A2H 0005A3H 0005A4H 0005A5H 0005A6H 0005A7H 0005A8H Register PPG10 - Period setting register PPG10 - Duty cycle register PPG10 - Duty cycle register PPG10 - Control status register Low PPG10 - Control status register High PPG11 - Timer register PPG11 - Timer register PPG11 - Period setting register PPG11 - Period setting register PPG11 - Duty cycle register PPG11 - Duty cycle register PPG11 - Control status register Low PPG11 - Control status register High PPG15-PPG12 - General Control register 1 Low PPG15-PPG12 - General Control register 1 High PPG15-PPG12 - General Control register 2 Low PPG15-PPG12 - General Control register 2 High PPG12 - Timer register PPG12 - Timer register PPG12 - Period setting register PPG12 - Period setting register PPG12 - Duty cycle register PPG12 - Duty cycle register PPG12 - Control status register Low PPG12 - Control status register High PPG13 - Timer register PPG13 - Timer register PPG13 - Period setting register PPG13 - Period setting register PPG13 - Duty cycle register PDUT13 PCSR13 PCNL12 PCNH12 PTMR13 PCN12 PDUT12 PCSR12 PCNL11 PCNH11 GCN1L3 GCN1H3 GCN2L3 GCN2H3 PTMR12 GCN23 GCN13 PCN11 PDUT11 PCSR11 PCNL10 PCNH10 PTMR11 PCN10 PDUT10 Abbreviation 8-bit access Abbreviation 16-bit access Access W W W R/W R/W R R W W W W R/W R/W R/W R/W R/W R/W R R W W W W R/W R/W R R W W W FME-MB96340 rev 10 45 MB96340 Series I/O map MB96(F)34x (23 of 30) Address 0005A9H 0005AAH 0005ABH 0005ACH 0005ADH 0005AEH 0005AFH 0005B0H 0005B1H 0005B2H 0005B3H 0005B4H 0005B5H 0005B6H 0005B7H 0005B8H 0005B9H 0005BAH 0005BBH 0005BCH00065FH 000660H 000661H 000662H 000663H 000664H0006DFH 0006E0H 0006E1H 0006E2H 0006E3H Register PPG13 - Duty cycle register PPG13 - Control status register Low PPG13 - Control status register High PPG14 - Timer register PPG14 - Timer register PPG14 - Period setting register PPG14 - Period setting register PPG14 - Duty cycle register PPG14 - Duty cycle register PPG14 - Control status register Low PPG14 - Control status register High PPG15 - Timer register PPG15 - Timer register PPG15 - Period setting register PPG15 - Period setting register PPG15 - Duty cycle register PPG15 - Duty cycle register PPG15 - Control status register Low PPG15 - Control status register High Reserved Peripheral Resource Relocation Register 10 Peripheral Resource Relocation Register 11 Peripheral Resource Relocation Register 12 Peripheral Resource Relocation Register 13 Reserved External Bus - Area configuration register 0 Low External Bus - Area configuration register 0 High External Bus - Area configuration register 1 Low External Bus - Area configuration register 1 High EACL0 EACH0 EACL1 EACH1 EAC1 EAC0 PRRR10 PRRR11 PRRR12 PRRR13 PCNL15 PCNH15 PCN15 PDUT15 PCSR15 PCNL14 PCNH14 PTMR15 PCN14 PDUT14 PCSR14 PCNL13 PCNH13 PTMR14 PCN13 Abbreviation 8-bit access Abbreviation 16-bit access Access W R/W R/W R R W W W W R/W R/W R R W W W W R/W R/W R/W R/W R/W W R/W R/W R/W R/W 46 FME-MB96340 rev 10 MB96340 Series I/O map MB96(F)34x (24 of 30) Address 0006E4H 0006E5H 0006E6H 0006E7H 0006E8H 0006E9H 0006EAH 0006EBH 0006ECH 0006EDH 0006EEH 0006EFH 0006F0H 0006F1H 0006F2H 0006F3H 0006F4H 0006F5H 0006F6H0006FFH 000700H 000701H 000702H 000703H 000704H 000705H 000706H 000707H 000708H 000709H Register External Bus - Area configuration register 2 Low External Bus - Area configuration register 2 High External Bus - Area configuration register 3 Low External Bus - Area configuration register 3 High External Bus - Area configuration register 4 Low External Bus - Area configuration register 4 High External Bus - Area configuration register 5 Low External Bus - Area configuration register 5 High External Bus - Area select register 2 External Bus - Area select register 3 External Bus - Area select register 4 External Bus - Area select register 5 External Bus - Mode register External Bus - Clock and Function register External Bus - Address output enable register 0 External Bus - Address output enable register 1 External Bus - Address output enable register 2 External Bus - Control signal register Reserved CAN0 - Control register Low CAN0 - Control register High (reserved) CAN0 - Status register Low CAN0 - Status register High (reserved) CAN0 - Error Counter Low (Transmit) CAN0 - Error Counter High (Receive) CAN0 - Bit Timing Register Low CAN0 - Bit Timing Register High CAN0 - Interrupt Register Low CAN0 - Interrupt Register High CTRLRL0 CTRLRH0 STATRL0 STATRH0 ERRCNTL0 ERRCNTH0 BTRL0 BTRH0 INTRL0 INTRH0 INTR0 BTR0 ERRCNT0 STATR0 CTRLR0 Abbreviation 8-bit access EACL2 EACH2 EACL3 EACH3 EACL4 EACH4 EACL5 EACH5 EAS2 EAS3 EAS4 EAS5 EBM EBCF EBAE0 EBAE1 EBAE2 EBCS EAC5 EAC4 EAC3 Abbreviation 16-bit access EAC2 Access R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R R/W R R R R/W R/W R R FME-MB96340 rev 10 47 MB96340 Series I/O map MB96(F)34x (25 of 30) Address 00070AH 00070BH 00070CH 00070DH 00070EH00070FH 000710H 000711H 000712H 000713H 000714H 000715H 000716H 000717H 000718H 000719H 00071AH 00071BH 00071CH 00071DH 00071EH 00071FH 000720H 000721H 000722H 000723H 000724H 000725H 000726H00073FH Register CAN0 - Test Register Low CAN0 - Test Register High (reserved) CAN0 - BRP Extension register Low CAN0 - BRP Extension register High (reserved) Reserved CAN0 - IF1 Command request register Low CAN0 - IF1 Command request register High CAN0 - IF1 Command Mask register Low CAN0 - IF1 Command Mask register High (reserved) CAN0 - IF1 Mask 1 Register Low CAN0 - IF1 Mask 1 Register High CAN0 - IF1 Mask 2 Register Low CAN0 - IF1 Mask 2 Register High CAN0 - IF1 Arbitration 1 Register Low CAN0 - IF1 Arbitration 1 Register High CAN0 - IF1 Arbitration 2 Register Low CAN0 - IF1 Arbitration 2 Register High CAN0 - IF1 Message Control Register Low CAN0 - IF1 Message Control Register High CAN0 - IF1 Data A1 Low CAN0 - IF1 Data A1 High CAN0 - IF1 Data A2 Low CAN0 - IF1 Data A2 High CAN0 - IF1 Data B1 Low CAN0 - IF1 Data B1 High CAN0 - IF1 Data B2 Low CAN0 - IF1 Data B2 High Reserved IF1CREQL0 IF1CREQH0 IF1CMSKL0 IF1CMSKH0 IF1MSK1L0 IF1MSK1H0 IF1MSK2L0 IF1MSK2H0 IF1ARB1L0 IF1ARB1H0 IF1ARB2L0 IF1ARB2H0 IF1MCTRL0 IF1MCTRH0 IF1DTA1L0 IF1DTA1H0 IF1DTA2L0 IF1DTA2H0 IF1DTB1L0 IF1DTB1H0 IF1DTB2L0 IF1DTB2H0 IF1DTB20 IF1DTB10 IF1DTA20 IF1DTA10 IF1MCTR0 IF1ARB20 IF1ARB10 IF1MSK20 IF1MSK10 IF1CMSK0 IF1CREQ0 Abbreviation 8-bit access TESTRL0 TESTRH0 BRPERL0 BRPERH0 BRPER0 Abbreviation 16-bit access TESTR0 Access R/W R R/W R R/W R/W R/W R R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W - 48 FME-MB96340 rev 10 MB96340 Series I/O map MB96(F)34x (26 of 30) Address 000740H 000741H 000742H 000743H 000744H 000745H 000746H 000747H 000748H 000749H 00074AH 00074BH 00074CH 00074DH 00074EH 00074FH 000750H 000751H 000752H 000753H 000754H 000755H 000756H00077FH 000780H 000781H 000782H 000783H 000784H00078FH Register CAN0 - IF2 Command request register Low CAN0 - IF2 Command request register High CAN0 - IF2 Command Mask register Low CAN0 - IF2 Command Mask register High (reserved) CAN0 - IF2 Mask 1 Register Low CAN0 - IF2 Mask 1 Register High CAN0 - IF2 Mask 2 Register Low CAN0 - IF2 Mask 2 Register High CAN0 - IF2 Arbitration 1 Register Low CAN0 - IF2 Arbitration 1 Register High CAN0 - IF2 Arbitration 2 Register Low CAN0 - IF2 Arbitration 2 Register High CAN0 - IF2 Message Control Register Low CAN0 - IF2 Message Control Register High CAN0 - IF2 Data A1 Low CAN0 - IF2 Data A1 High CAN0 - IF2 Data A2 Low CAN0 - IF2 Data A2 High CAN0 - IF2 Data B1 Low CAN0 - IF2 Data B1 High CAN0 - IF2 Data B2 Low CAN0 - IF2 Data B2 High Reserved CAN0 - Transmission Request 1 Register Low CAN0 - Transmission Request 1 Register High CAN0 - Transmission Request 2 Register Low CAN0 - Transmission Request 2 Register High Reserved TREQR1L0 TREQR1H0 TREQR2L0 TREQR2H0 TREQR20 TREQR10 Abbreviation 8-bit access IF2CREQL0 IF2CREQH0 IF2CMSKL0 IF2CMSKH0 IF2MSK1L0 IF2MSK1H0 IF2MSK2L0 IF2MSK2H0 IF2ARB1L0 IF2ARB1H0 IF2ARB2L0 IF2ARB2H0 IF2MCTRL0 IF2MCTRH0 IF2DTA1L0 IF2DTA1H0 IF2DTA2L0 IF2DTA2H0 IF2DTB1L0 IF2DTB1H0 IF2DTB2L0 IF2DTB2H0 IF2DTB20 IF2DTB10 IF2DTA20 IF2DTA10 IF2MCTR0 IF2ARB20 IF2ARB10 IF2MSK20 IF2MSK10 IF2CMSK0 Abbreviation 16-bit access IF2CREQ0 Access R/W R/W R/W R R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R R R R - FME-MB96340 rev 10 49 MB96340 Series I/O map MB96(F)34x (27 of 30) Address 000790H 000791H 000792H 000793H 000794H00079FH 0007A0H 0007A1H 0007A2H 0007A3H 0007A4H0007AFH 0007B0H 0007B1H 0007B2H 0007B3H 0007B4H0007CDH 0007CEH 0007CFH0007FFH 000800H 000801H 000802H 000803H 000804H 000805H 000806H 000807H 000808H 000809H Register CAN0 - New Data 1 Register Low CAN0 - New Data 1 Register High CAN0 - New Data 2 Register Low CAN0 - New Data 2 Register High Reserved CAN0 - Interrupt Pending 1 Register Low CAN0 - Interrupt Pending 1 Register High CAN0 - Interrupt Pending 2 Register Low CAN0 - Interrupt Pending 2 Register High Reserved CAN0 - Message Valid 1 Register Low CAN0 - Message Valid 1 Register High CAN0 - Message Valid 2 Register Low CAN0 - Message Valid 2 Register High Reserved CAN0 - Output enable register Reserved CAN1 - Control register Low CAN1 - Control register High (reserved) CAN1 - Status register Low CAN1 - Status register High (reserved) CAN1 - Error Counter Low (Transmit) CAN1 - Error Counter High (Receive) CAN1 - Bit Timing Register Low CAN1 - Bit Timing Register High CAN1 - Interrupt Register Low CAN1 - Interrupt Register High CTRLRL1 CTRLRH1 STATRL1 STATRH1 ERRCNTL1 ERRCNTH1 BTRL1 BTRH1 INTRL1 INTRH1 INTR1 BTR1 ERRCNT1 STATR1 CTRLR1 COER0 MSGVAL1L0 MSGVAL1H0 MSGVAL2L0 MSGVAL2H0 MSGVAL20 MSGVAL10 INTPND1L0 INTPND1H0 INTPND2L0 INTPND2H0 INTPND20 INTPND10 Abbreviation 8-bit access NEWDT1L0 NEWDT1H0 NEWDT2L0 NEWDT2H0 NEWDT20 Abbreviation 16-bit access NEWDT10 Access R R R R R R R R R R R R R/W R/W R R/W R R R R/W R/W R R 50 FME-MB96340 rev 10 MB96340 Series I/O map MB96(F)34x (28 of 30) Address 00080AH 00080BH 00080CH 00080DH 00080EH00080FH 000810H 000811H 000812H 000813H 000814H 000815H 000816H 000817H 000818H 000819H 00081AH 00081BH 00081CH 00081DH 00081EH 00081FH 000820H 000821H 000822H 000823H 000824H 000825H 000826H00083FH Register CAN1 - Test Register Low CAN1 - Test Register High (reserved) CAN1 - BRP Extension register Low CAN1 - BRP Extension register High (reserved) Reserved CAN1 - IF1 Command request register Low CAN1 - IF1 Command request register High CAN1 - IF1 Command Mask register Low CAN1 - IF1 Command Mask register High (reserved) CAN1 - IF1 Mask 1 Register Low CAN1 - IF1 Mask 1 Register High CAN1 - IF1 Mask 2 Register Low CAN1 - IF1 Mask 2 Register High CAN1 - IF1 Arbitration 1 Register Low CAN1 - IF1 Arbitration 1 Register High CAN1 - IF1 Arbitration 2 Register Low CAN1 - IF1 Arbitration 2 Register High CAN1 - IF1 Message Control Register Low CAN1 - IF1 Message Control Register High CAN1 - IF1 Data A1 Low CAN1 - IF1 Data A1 High CAN1 - IF1 Data A2 Low CAN1 - IF1 Data A2 High CAN1 - IF1 Data B1 Low CAN1 - IF1 Data B1 High CAN1 - IF1 Data B2 Low CAN1 - IF1 Data B2 High Reserved IF1CREQL1 IF1CREQH1 IF1CMSKL1 IF1CMSKH1 IF1MSK1L1 IF1MSK1H1 IF1MSK2L1 IF1MSK2H1 IF1ARB1L1 IF1ARB1H1 IF1ARB2L1 IF1ARB2H1 IF1MCTRL1 IF1MCTRH1 IF1DTA1L1 IF1DTA1H1 IF1DTA2L1 IF1DTA2H1 IF1DTB1L1 IF1DTB1H1 IF1DTB2L1 IF1DTB2H1 IF1DTB21 IF1DTB11 IF1DTA21 IF1DTA11 IF1MCTR1 IF1ARB21 IF1ARB11 IF1MSK21 IF1MSK11 IF1CMSK1 IF1CREQ1 Abbreviation 8-bit access TESTRL1 TESTRH1 BRPERL1 BRPERH1 BRPER1 Abbreviation 16-bit access TESTR1 Access R/W R R/W R R/W R/W R/W R R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W - FME-MB96340 rev 10 51 MB96340 Series I/O map MB96(F)34x (29 of 30) Address 000840H 000841H 000842H 000843H 000844H 000845H 000846H 000847H 000848H 000849H 00084AH 00084BH 00084CH 00084DH 00084EH 00084FH 000850H 000851H 000852H 000853H 000854H 000855H 000856H00087FH 000880H 000881H 000882H 000883H 000884H00088FH Register CAN1 - IF2 Command request register Low CAN1 - IF2 Command request register High CAN1 - IF2 Command Mask register Low CAN1 - IF2 Command Mask register High (reserved) CAN1 - IF2 Mask 1 Register Low CAN1 - IF2 Mask 1 Register High CAN1 - IF2 Mask 2 Register Low CAN1 - IF2 Mask 2 Register High CAN1 - IF2 Arbitration 1 Register Low CAN1 - IF2 Arbitration 1 Register High CAN1 - IF2 Arbitration 2 Register Low CAN1 - IF2 Arbitration 2 Register High CAN1 - IF2 Message Control Register Low CAN1 - IF2 Message Control Register High CAN1 - IF2 Data A1 Low CAN1 - IF2 Data A1 High CAN1 - IF2 Data A2 Low CAN1 - IF2 Data A2 High CAN1 - IF2 Data B1 Low CAN1 - IF2 Data B1 High CAN1 - IF2 Data B2 Low CAN1 - IF2 Data B2 High Reserved CAN1 - Transmission Request 1 Register Low CAN1 - Transmission Request 1 Register High CAN1 - Transmission Request 2 Register Low CAN1 - Transmission Request 2 Register High Reserved TREQR1L1 TREQR1H1 TREQR2L1 TREQR2H1 TREQR21 TREQR11 Abbreviation 8-bit access IF2CREQL1 IF2CREQH1 IF2CMSKL1 IF2CMSKH1 IF2MSK1L1 IF2MSK1H1 IF2MSK2L1 IF2MSK2H1 IF2ARB1L1 IF2ARB1H1 IF2ARB2L1 IF2ARB2H1 IF2MCTRL1 IF2MCTRH1 IF2DTA1L1 IF2DTA1H1 IF2DTA2L1 IF2DTA2H1 IF2DTB1L1 IF2DTB1H1 IF2DTB2L1 IF2DTB2H1 IF2DTB21 IF2DTB11 IF2DTA21 IF2DTA11 IF2MCTR1 IF2ARB21 IF2ARB11 IF2MSK21 IF2MSK11 IF2CMSK1 Abbreviation 16-bit access IF2CREQ1 Access R/W R/W R/W R R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R R R R - 52 FME-MB96340 rev 10 MB96340 Series I/O map MB96(F)34x (30 of 30) Address 000890H 000891H 000892H 000893H 000894H00089FH 0008A0H 0008A1H 0008A2H 0008A3H 0008A4H0008AFH 0008B0H 0008B1H 0008B2H 0008B3H 0008B4H0008CDH 0008CEH 0008CFH0009FFH 000A00H 000A01H 000A02H 000A03H 000A04H 000A05H 000A06H000BFFH Register CAN1 - New Data 1 Register Low CAN1 - New Data 1 Register High CAN1 - New Data 2 Register Low CAN1 - New Data 2 Register High Reserved CAN1 - Interrupt Pending 1 Register Low CAN1 - Interrupt Pending 1 Register High CAN1 - Interrupt Pending 2 Register Low CAN1 - Interrupt Pending 2 Register High Reserved CAN1 - Message Valid 1 Register Low CAN1 - Message Valid 1 Register High CAN1 - Message Valid 2 Register Low CAN1 - Message Valid 2 Register High Reserved CAN1 - Output enable register Reserved DMA - IO address block register 0 DMA - IO address block register 1 DMA - IO address block register 2 DMA - IO address block register 3 DMA - IO address block register 4 DMA - IO address block register 5 Reserved IOABK0 IOABK1 IOABK2 IOABK3 IOABK4 IOABK5 COER1 MSGVAL1L1 MSGVAL1H1 MSGVAL2L1 MSGVAL2H1 MSGVAL21 MSGVAL11 INTPND1L1 INTPND1H1 INTPND2L1 INTPND2H1 INTPND21 INTPND11 Abbreviation 8-bit access NEWDT1L1 NEWDT1H1 NEWDT2L1 NEWDT2H1 NEWDT21 Abbreviation 16-bit access NEWDT11 Access R R R R R R R R R R R R R/W R/W R/W R/W R/W R/W R/W - Note: Any write access to reserved addresses in the I/O map should not be performed. A read access to a reserved address results in reading ‘X’. Registers of resources which are described in this table, but which are not supported by the device, should also be handled as “Reserved”. FME-MB96340 rev 10 53 MB96340 Series ■ INTERRUPT VECTOR TABLE Interrupt vector table MB96(F)34x (1 of 4) Vector number 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Offset in vector table 3FCH 3F8H 3F4H 3F0H 3ECH 3E8H 3E4H 3E0H 3DCH 3D8H 3D4H 3D0H 3CCH 3C8H 3C4H 3C0H 3BCH 3B8H 3B4H 3B0H 3ACH 3A8H 3A4H 3A0H 39CH 398H 394H 390H Vector name CALLV0 CALLV1 CALLV2 CALLV3 CALLV4 CALLV5 CALLV6 CALLV7 RESET INT9 EXCEPTION NMI DLY RC_TIMER MC_TIMER SC_TIMER RESERVED EXTINT0 EXTINT1 EXTINT2 EXTINT3 EXTINT4 EXTINT5 EXTINT6 EXTINT7 EXTINT8 EXTINT9 EXTINT10 Cleared by DMA No No No No No No No No No No No No No No No No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Index in ICR to program 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Non-Maskable Interrupt Delayed Interrupt RC Timer Main Clock Timer Sub Clock Timer Reserved External Interrupt 0 External Interrupt 1 External Interrupt 2 External Interrupt 3 External Interrupt 4 External Interrupt 5 External Interrupt 6 External Interrupt 7 External Interrupt 8 External Interrupt 9 External Interrupt 10 Description 54 FME-MB96340 rev 10 MB96340 Series Interrupt vector table MB96(F)34x (2 of 4) Vector number 28 29 30 31 32 33 Offset in vector table 38CH 388H 384H 380H 37CH 378H Vector name EXTINT11 EXTINT12 EXTINT13 EXTINT14 EXTINT15 CAN0 Cleared by DMA Yes Yes Yes Yes Yes No Index in ICR to program 28 29 30 31 32 33 Description External Interrupt 11 External Interrupt 12 External Interrupt 13 External Interrupt 14 External Interrupt 15 CAN Controller 0 (except MB96(F)34xAyy or MB96(F)34xCyy) CAN Controller 1 (except MB96(F)34xAyy, MB96(F)34xCyy, MB96F345Dyy or MB96F345Fyy) Programmable Pulse Generator 0 Programmable Pulse Generator 1 Programmable Pulse Generator 2 Programmable Pulse Generator 3 Programmable Pulse Generator 4 Programmable Pulse Generator 5 Programmable Pulse Generator 6 Programmable Pulse Generator 7 Programmable Pulse Generator 8 Programmable Pulse Generator 9 Programmable Pulse Generator 10 Programmable Pulse Generator 11 Programmable Pulse Generator 12 Programmable Pulse Generator 13 Programmable Pulse Generator 14 Programmable Pulse Generator 15 Reload Timer 0 Reload Timer 1 Reload Timer 2 Reload Timer 3 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 374H 370H 36CH 368H 364H 360H 35CH 358H 354H 350H 34CH 348H 344H 340H 33CH 338H 334H 330H 32CH 328H 324H CAN1 PPG0 PPG1 PPG2 PPG3 PPG4 PPG5 PPG6 PPG7 PPG8 PPG9 PPG10 PPG11 PPG12 PPG13 PPG14 PPG15 RLT0 RLT1 RLT2 RLT3 No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 FME-MB96340 rev 10 55 MB96340 Series Interrupt vector table MB96(F)34x (3 of 4) Vector number 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 Offset in vector table 320H 31CH 318H 314H 310H 30CH 308H 304H 300H 2FCH 2F8H 2F4H 2F0H 2ECH 2E8H 2E4H 2E0H 2DCH 2D8H 2D4H 2D0H 2CCH 2C8H 2C4H 2C0H 2BCH 2B8H 2B4H Vector name PPGRLT ICU0 ICU1 ICU2 ICU3 ICU4 ICU5 ICU6 ICU7 OCU0 OCU1 OCU2 OCU3 OCU4 OCU5 OCU6 OCU7 FRT0 FRT1 IIC0 IIC1 ADC0 ALARM0 ALARM1 LINR0 LINT0 LINR1 LINT1 Cleared by DMA Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No Yes Yes Yes Yes Index in ICR to program 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 Description Reload Timer 6 - dedicated for PPG Input Capture Unit 0 Input Capture Unit 1 Input Capture Unit 2 Input Capture Unit 3 Input Capture Unit 4 Input Capture Unit 5 Input Capture Unit 6 Input Capture Unit 7 Output Compare Unit 0 Output Compare Unit 1 Output Compare Unit 2 Output Compare Unit 3 Output Compare Unit 4 Output Compare Unit 5 Output Compare Unit 6 Output Compare Unit 7 Free Running Timer 0 Free Running Timer 1 I2C interface I2C interface A/D Converter Alarm Comparator 0 (except MB96F345Dyy or MB96F345Fyy) Alarm Comparator 1 (except MB96F345Dyy or MB96F345Fyy) LIN USART 0 RX LIN USART 0 TX LIN USART 1 RX LIN USART 1 TX 56 FME-MB96340 rev 10 MB96340 Series Interrupt vector table MB96(F)34x (4 of 4) Vector number 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 Offset in vector table 2B0H 2ACH 2A8H 2A4H 2A0H 29CH 298H 294H 290H 28CH 288H 284H 280H 27CH 278H Vector name LINR2 LINT2 LINR3 LINT3 FLASH_A FLASH_B LINR7 LINT7 LINR8 LINT8 LINR9 LINT9 RTC0 CAL0 DFLASH_A Cleared by DMA Yes Yes Yes Yes No No Yes Yes Yes Yes Yes Yes No No Yes Index in ICR to program 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 Description LIN USART 2 RX LIN USART 2 TX LIN USART 3 RX LIN USART 3 TX Flash memory A (only Flash devices) Flash memory B (only MB96F348T/H/C) LIN USART 7 RX LIN USART 7 TX LIN USART 8 RX LIN USART 8 TX LIN USART 9 RX LIN USART 9 TX Real Timer Clock Clock Calibration Unit Data Flash A (only MB96F345Dyy, MB96F345Fyy) FME-MB96340 rev 10 57 MB96340 Series ■ HANDLING DEVICES Special care is required for the following when handling the device: • • • • • • • • • • • • • Latch-up prevention Unused pins handling External clock usage Unused sub clock signal Notes on PLL clock mode operation Power supply pins (VCC/VSS) Crystal oscillator circuit Turn on sequence of power supply to A/D converter and analog inputs Pin handling when not using the A/D converter Notes on energization Stabilization of power supply voltage Serial communication Handling of Data Flash 1. Latch-up prevention CMOS IC chips may suffer latch-up under the following conditions: • A voltage higher than VCC or lower than VSS is applied to an input or output pin. • A voltage higher than the rated voltage is applied between VCC pins and VSS pins. • The AVCC power supply is applied before the VCC voltage. Latch-up may increase the power supply current dramatically, causing thermal damages to the device. For the same reason, extra care is required to not let the analog power-supply voltage (AVCC, AVRH) exceed the digital power-supply voltage. 2. Unused pins handling Unused input pins can be left open when the input is disabled (corresponding bit of Port Input Enable register PIER = 0). Leaving unused input pins open when the input is enabled may result in misbehavior and possible permanent damage of the device. They must therefore be pulled up or pulled down through resistors. To prevent latch-up, those resistors should be more than 2 kΩ. Unused bidirectional pins can be set either to the output state and be then left open, or to the input state with either input disabled or external pull-up/pull-down resistor as described above. 3. External clock usage The permitted frequency range of an external clock depends on the oscillator type and configuration. See AC Characteristics for detailed modes and frequency limits. Single and opposite phase external clocks must be connected as follows: 1. Single phase external clock • When using a single phase external clock, X0 (X0A) pin must be driven and X1 (X1A) pin left open. X0 X1 58 FME-MB96340 rev 10 MB96340 Series 2. Opposite phase external clock • When using an opposite phase external clock, X1 (X1A) must be supplied with a clock signal which has the opposite phase to the X0 (X0A) pins. X0 X1 4. Unused sub clock signal If the pins X0A and X1A are not connected to an oscillator, a pull-down resistor must be connected on the X0A pin and the X1A pin must be left open. 5. Notes on PLL clock mode operation If the PLL clock mode is selected and no external oscillator is operating or no external clock is supplied, the microcontroller attempts to work with the free oscillating PLL. Performance of this operation, however, cannot be guaranteed. 6. Power supply pins (VCC/VSS) It is required that all VCC-level as well as all VSS-level power supply pins are at the same potential. If there is more than one VCC or VSS level, the device may operate incorrectly or be damaged even within the guaranteed operating range. VCC and VSS must be connected to the device from the power supply with lowest possible impedance. As a measure against power supply noise, it is required to connect a bypass capacitor of about 0.1 µF between VCC and VSS as close as possible to VCC and VSS pins. 7. Crystal oscillator and ceramic resonator circuit Noise at X0, X1 pins or X0A, X1A pins might cause abnormal operation. It is required to provide bypass capacitors with shortest possible distance to X0, X1 pins and X0A, X1A pins, crystal oscillator (or ceramic resonator) and ground lines, and, to the utmost effort, that the lines of oscillation circuit do not cross the lines of other circuits. It is highly recommended to provide a printed circuit board art work surrounding X0, X1 pins and X0A, X1A pins with a ground area for stabilizing the operation. It is highly recommended to evaluate the quartz/MCU or resonator/MCU system at the quartz or resonator manufacturer, especially when using low-Q resonators at higher frequencies. 8. Turn on sequence of power supply to A/D converter and analog inputs It is required to turn the A/D converter power supply (AVCC, AVRH, AVRL) and analog inputs (ANn) on after turning the digital power supply (VCC) on. It is also required to turn the digital power off after turning the A/D converter supply and analog inputs off. In this case, the voltage must not exceed AVRH or AVCC (turning the analog and digital power supplies simultaneously on or off is acceptable). 9. Pin handling when not using the A/D converter It is required to connect the unused pins of the A/D converter as AVCC = VCC, AVSS = AVRH = AVRL = VSS. 10. Notes on Power-on To prevent malfunction of the internal voltage regulator, supply voltage profile while turning the power supply on should be slower than 50µs from 0.2 V to 2.7 V. FME-MB96340 rev 10 59 MB96340 Series 11. Stabilization of power supply voltage If the power supply voltage varies acutely even within the operation safety range of the Vcc power supply voltage, a malfunction may occur. The Vcc power supply voltage must therefore be stabilized. As stabilization guidelines, the power supply voltage must be stabilized in such a way that Vcc ripple fluctuations (peak to peak value) in the commercial frequencies (50 to 60 Hz) fall within 10% of the standard Vcc power supply voltage and the transient fluctuation rate becomes 0.1V/µs or less in instantaneous fluctuation for power supply switching. 12. Serial communication There is a possibility to receive wrong data due to noise or other causes on the serial communication. Therefore, design a printed circuit board so as to avoid noise. Consider receiving of wrong data when designing the system. For example apply a checksum and retransmit the data if an error occurs. 13. Handling of Data Flash The Data Flash requires different and additional control signals for parallel programming. Please check with your programming equipment maker for support of this interface. 60 FME-MB96340 rev 10 MB96340 Series ■ ELECTRICAL CHARACTERISTICS 1. Absolute Maximum Ratings Parameter Power supply voltage AD Converter voltage references Input voltage Output voltage Maximum Clamp Current Total Maximum Clamp Current “L” level maximum output current “L” level average output current “L” level maximum overall output current “L” level average overall output current ”H” level maximum output current ”H” level average output current ”H” level maximum overall output current ”H” level average overall output current Symbol VCC AVCC AVRH, AVRL VI VO ICLAMP Σ|ICLAMP| IOL1 IOLAV1 ΣIOL1 ΣIOLAV1 IOH1 IOHAV1 ΣIOH1 ΣIOHAV1 Rating Min Max VSS - 0.3 VSS + 6.0 VSS - 0.3 VSS + 6.0 VSS - 0.3 VSS + 6.0 VSS - 0.3 VSS + 6.0 VSS - 0.3 VSS + 6.0 -4.0 Permitted Power dissipation (Flash devices in QFP package) *4 PD Permitted Power dissipation (MB96F346/F347/F348 in LQFP package) *4 PD +4.0 40 15 5 100 50 -15 -5 -100 -50 430*5 750*5 540*5 375*5 750*5 470*5 560*5 Unit V V V V V mA mA VCC = AVCC *1 AVCC ≥ AVRH, AVCC ≥ AVRL, AVRH > AVRL, AVRL ≥ AVSS VI ≤ VCC + 0.3V *2 Remarks VO ≤ VCC + 0.3V *2 Applicable to general purpose I/O pins *3 Applicable to general purpose I/O pins *3 mA Normal outputs with driving strength set to 5mA mA Normal outputs with driving strength set to 5mA mA Normal outputs mA Normal outputs mA Normal outputs with driving strength set to 5mA mA Normal outputs with driving strength set to 5mA mA Normal outputs mA Normal outputs mW TA=105oC mW TA=90oC mW TA=125oC, no Flash program/ erase *6 mW TA=105oC mW TA=85oC mW mW TA=125oC, no Flash program/ erase *6 TA=120oC, no Flash program/ erase *6 FME-MB96340 rev 10 61 MB96340 Series Rating Min Permitted Power dissipation (MB96F345 in LQFP package) *4 PD Permitted Power dissipation (Mask ROM devices) *4 PD 0 Operating ambient temperature TA -40 -40 Storage temperature TSTG -55 420*5 590*5 350 360 +70 +105 +125 +150 o o Parameter Symbol Max 335*5 670*5 840*5 Unit mW TA=105oC mW TA=85oC mW TA=75oC mW mW Remarks TA=125oC, no Flash program/ erase *6 TA=115oC, no Flash program/ erase *6 mW TA=105oC mW TA=125oC *6 MB96V300B C *6 C *1: AVCC and VCC must be set to the same voltage. It is required that AVCC does not exceed VCC and that the voltage at the analog inputs does not exceed AVCC neither when the power is switched on. *2: VI and VO should not exceed VCC + 0.3 V. VI should also not exceed the specified ratings. However if the maximum current to/from a input is limited by some means with external components, the ICLAMP rating supersedes the VI rating. Input/output voltages of standard ports depend on VCC. *3: • Applicable to all general purpose I/O pins (Pnn_m) • Use within recommended operating conditions. • Use at DC voltage (current) • The +B signal should always be applied a limiting resistance placed between the +B signal and the microcontroller. • The value of the limiting resistance should be set so that when the +B signal is applied the input current to the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods. • Note that when the microcontroller drive current is low, such as in the power saving modes, the +B input potential may pass through the protective diode and increase the potential at the VCC pin, and this may affect other devices. • Note that if a +B signal is input when the microcontroller power supply is off (not fixed at 0 V), the power supply is provided from the pins, so that incomplete operation may result. • Note that if the +B input is applied during power-on, the power supply is provided from the pins and the resulting supply voltage may not be sufficient to operate the Power reset (except devices with persistent low voltage reset in internal vector mode). 62 FME-MB96340 rev 10 MB96340 Series • Sample recommended circuits: Protective Diode VCC Limiting resistance +B input (0V to 16V) P-ch N-ch R *4: The maximum permitted power dissipation depends on the ambient temperature, the air flow velocity and the thermal conductance of the package on the PCB. The actual power dissipation depends on the customer application and can be calculated as follows: PD = PIO + PINT PIO = ∑ (VOL * IOL + VOH * IOH) (IO load power dissipation, sum is performed on all IO ports) PINT = VCC * (ICC + IA) (internal power dissipation) ICC is the total core current consumption into VCC as described in the “DC characteristics” and depends on the selected operation mode and clock frequency and the usage of functions like Flash programming or the clock modulator. IA is the analog current consumption into AVCC. *5: Worst case value for a package mounted on single layer PCB at specified TA without air flow. *6: Please contact Fujitsu for reliability limitations when using under these conditions. WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings. FME-MB96340 rev 10 63 MB96340 Series 2. Recommended Operating Conditions Value Min 3.0 3.5 Typ 4.7 Max 5.5 15 Parameter Power supply voltage Smoothing capacitor at C pin Symbol VCC CS Unit V µF Remarks Use a X7R ceramic capacitor or a capacitor that has similar frequency characteristics WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device’s electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their FUJITSU representatives beforehand. 64 FME-MB96340 rev 10 MB96340 Series 3. DC characteristics (TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V) Parameter Input H voltage Symbol Pin Condition CMOS Hysteresis 0.8/0.2 input selected CMOS Hysteresis Port inputs 0.7/0.3 input selected Pnn_m AUTOMOTIVE Hysteresis input selected TTL input selected VIHX0F VIHX0S VIHR VIHM Input L voltage X0 X0,X1, X0A,X1A RSTX MD2-MD0 External clock in “Fast Clock Input mode” External clock in “oscillation mode” CMOS Hysteresis 0.8/0.2 input selected CMOS Hysteresis 0.7/0.3 input sePort inputs lected Pnn_m AUTOMOTIVE Hysteresis input selected TTL input selected VILX0F VILX0S VILR VILM X0 X0,X1, X0A,X1A RSTX MD2-MD0 External clock in “Fast Clock Input mode” External clock in “oscillation mode” Value Min 0.8 VCC 0.7 VCC 0.74 VCC 0.8 VCC 2.0 0.8 VCC 2.5 0.8 VCC VCC 0.3 VSS 0.3 VSS 0.3 VSS 0.3 VSS 0.3 VSS 0.3 VSS 0.3 VSS 0.3 VSS 0.3 VSS 0.3 Typ - Max VCC + 0.3 VCC + 0.3 VCC + 0.3 VCC + 0.3 VCC + 0.3 VCC + 0.3 VCC + 0.3 VCC + 0.3 VCC + 0.3 0.2 VCC 0.3 VCC 0.5 VCC 0.46 VCC 0.8 Unit Remarks Not available in MB96F345 VCC ≥ 4.5V VCC < 4.5V V V V V V V V V V V - VIH - - Not available in MB96F345 Not available in MB96F34xY/R/AxA - - CMOS Hysteresis input - Not available in MB96F345 - V V VCC ≥ 4.5V VCC < 4.5V V V V V V CMOS Hysteresis input Not available in MB96F345 Not available in MB96F34xY/R/AxA VIL - - 0.2 VCC - 0.4 0.2 VCC VSS + 0.3 FME-MB96340 rev 10 65 MB96340 Series (TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V) Parameter Output H voltage VOH2 Normal outputs Symbol Pin Condition 4.5V ≤ VCC ≤ 5.5V IOH = -2mA 3.0V ≤ VCC < 4.5V IOH = -1.6mA 4.5V ≤ VCC ≤ 5.5V VCC 0.5 - Value Min Typ Max Unit Remarks V Driving strength set to 2mA (PODR:OD=1) VOH5 Normal outputs IOH = -5mA 3.0V ≤ VCC < 4.5V IOH = -3mA 4.5V ≤ VCC ≤ 5.5V VCC 0.5 - - V Driving strength set to 5mA (PODR:OD=0) VOH3 3mA outputs IOH = -3mA 3.0V ≤ VCC < 4.5V IOH = -2mA 4.5V ≤ VCC ≤ 5.5V VCC 0.5 - - V I/O circuit type “N” Output L voltage VOL2 Normal outputs IOL = +2mA 3.0V ≤ VCC < 4.5V IOL = +1.6mA 4.5V ≤ VCC ≤ 5.5V - - 0.4 V Driving strength set to 2mA (PODR:OD=1) VOL5 Normal outputs IOL = +5mA 3.0V ≤ VCC < 4.5V IOL = +3mA 3.0V ≤ VCC ≤ 5.5V IOL = +3mA - - 0.4 V Driving strength set to 5mA (PODR:OD=0) VOL3 3mA outputs Pnn_m Pnn_m, RSTX - - 0.4 V I/O circuit type “N” VSS < VI < VCC Input leak current IIL AVSS, AVRL < VI < AVCC, AVRH VCC = 3.3V ± 10% VCC = 5.0V ± 10% -1 40 25 100 50 +1 160 100 µA Single port pin kΩ kΩ Pull-up resistance RUP 66 FME-MB96340 rev 10 MB96340 Series (TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V) Parameter Symbol Condition (at TA) +25˚C +125˚C PLL Run mode with CLKS1/2 = CLKB = CLKP1 = 16MHz, CLKP2 = 8MHz 1 Flash/ROM wait state (CLKRC and CLKSC stopped) +25˚C +125˚C +25˚C +125˚C +25˚C +125˚C +25˚C +125˚C PLL Run mode with CLKS1/2 = CLKB = CLKP1 = 32MHz, CLKP2 = 16MHz 2 Flash/ROM wait states (CLKRC and CLKSC stopped) +25˚C +125˚C +25˚C +125˚C +25˚C +125˚C +25˚C +125˚C PLL Run mode with CLKS1/2 = 48MHz, CLKB = CLKP1/2 = 24MHz 0 Flash/ROM wait states (CLKRC and CLKSC stopped) +25˚C +125˚C +25˚C +125˚C +25˚C +125˚C Value Typ 8 8.5 15 16 17 18.5 16 17.5 14 14.5 23.5 25 26 28 25 27 13 13.5 27 29 31 33 30 32 Max 11 mA MB96345/346 13 20 mA MB96F345 23 22 mA 25.5 21 mA MB96F348T/H/CyB/C 24.5 18 mA MB96345/346 20 29.5 mA MB96F345 32.5 32 mA 36 31 mA MB96F348T/H/CyB/C 35 17 mA MB96345/346 19 39 mA MB96F345 42 43 mA 47 42 mA MB96F348T/H/CyB/C 46 MB96F346/F347/F348Y/ R/Ayy MB96F346/F347/F348Y/ R/Ayy MB96F346/F347/F348Y/ R/Ayy Unit Remarks Power supply current in Run modes* ICCPLL FME-MB96340 rev 10 67 MB96340 Series (TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V) Parameter Symbol Condition (at TA) +25˚C PLL Run mode with CLKS1/2 = CLKB = CLKP1= 56MHz, CLKP2 = 28MHz 2 Flash/ROM wait states (CLKRC and CLKSC stopped. Core voltage at 1.9V) PLL Run mode with CLKS1/2 = 72MHz, CLKB = CLKP1 = 36MHz, CLKP2 = 18MHz 1 Flash wait state (CLKRC and CLKSC stopped. Core voltage at 1.9V) PLL Run mode with CLKS1/2 = 80MHz, CLKB = CLKP1 = 40MHz, CLKP2 = 20MHz 1 Flash wait state (CLKRC and CLKSC stopped. Core voltage at 1.9V) PLL Run mode with CLKS1/2 = 96MHz, CLKB = CLKP1= 48MHz, CLKP2 = 24MHz 1 Flash/ROM wait state (CLKRC and CLKSC stopped. Core voltage at 1.9V) +25˚C +125˚C +25˚C +125˚C +25˚C Main Run mode with CLKS1/2 = CLKB = CLKP1/2 = 4MHz ICCMAIN 1 Flash/ROM wait state (CLKPLL, CLKSC and CLKRC stopped) +125˚C +25˚C +125˚C +25˚C +125˚C 24 24.5 49 51 2.3 2.8 4 4.6 4.5 5.2 28.5 mA MB96345/346 30.5 62 mA MB96F348T/H/CyB/C 66 3.3 mA MB96345/346 5.3 5 mA MB96F345 7.2 5.5 mA MB96F346/F347/F348 8.5 +25˚C 38 51 +125˚C +25˚C +125˚C +25˚C +125˚C +25˚C Value Typ 24 24.5 46 48 44 46 38 Max 29 mA MB96345/346 31 57 mA 61 55 mA MB96F348T/H/CyB/C 59 51 MB96F346/F347/F348Y/ R/Ayy Unit Remarks mA +125˚C 40 55 MB96F346/F347/F348Y/ R/Ayy ICCPLL Power supply current in Run modes* mA MB96F345 +125˚C 40 54 68 FME-MB96340 rev 10 MB96340 Series (TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V) Parameter Symbol Condition (at TA) +25˚C RC Run mode with CLKS1/2 = CLKB = CLKP1/2 = 2MHz ICCRCH 1 Flash/ROM wait state (CLKMC, CLKPLL and CLKSC stopped) +125˚C +25˚C +125˚C +25˚C +125˚C RC Run mode with CLKS1/2 = CLKB = CLKP1/2 = 100kHz, SMCR:LPMS = 0 1 Flash/ROM wait state (CLKMC, CLKPLL and CLKSC stopped. Voltage regulator in high power mode) ICCRCL RC Run mode with CLKS1/2 = CLKB = CLKP1/2 = 100kHz, SMCR:LPMS = 1 1 Flash/ROM wait state +25˚C +125˚C +25˚C 0.08 0.47 0.15 0.7 0.15 0.7 0.04 0.43 0.1 0.65 0.1 0.65 0.17 mA MB96345/346 1.92 0.25 mA MB96F345 2.25 0.25 mA MB96F346/F347/F348 3.05 0.12 mA MB96345/346 +125˚C +25˚C 1.85 0.2 mA MB96F345 2.2 0.2 mA MB96F346/F347/F348 3 +125˚C +25˚C +125˚C 0.73 0.4 0.95 2.3 0.6 mA MB96F346/F347/F348 3.4 +25˚C +125˚C +25˚C Value Typ 1.5 2 2.5 3.1 2.9 3.6 0.35 0.75 0.18 Max 2.5 mA MB96345/346 4.4 3.5 mA MB96F345 5.7 4 mA MB96F346/F347/F348 7 0.55 mA MB96345/346 2.3 0.3 mA MB96F345 Unit Remarks Power supply current in Run modes* (CLKMC, CLKPLL and +125˚C CLKSC stopped. Voltage +25˚C regulator in low power mode, no Flash programming/erasing allowed) +125˚C +25˚C Sub Run mode with CLKS1/2 = CLKB = CLKP1/2 = 32kHz ICCSUB 1 Flash/ROM wait state (CLKMC, CLKPLL and +125˚C CLKRC stopped, no Flash programming/erasing al- +25˚C lowed) +125˚C FME-MB96340 rev 10 69 MB96340 Series (TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V) Parameter Symbol Condition (at TA) +25˚C +125˚C PLL Sleep mode with CLKS1/2 = CLKP1 = 16MHz, CLKP2 = 8MHz (CLKRC and CLKSC stopped) +25˚C +125˚C +25˚C +125˚C +25˚C +125˚C +25˚C +125˚C PLL Sleep mode with CLKS1/2 = CLKP1 = 32MHz, CLKP2 = 16MHz (CLKRC and CLKSC stopped) +25˚C +125˚C +25˚C +125˚C +25˚C +125˚C +25˚C +125˚C PLL Sleep mode with CLKS1/2 = 48MHz, CLKP1/2 = 24MHz (CLKRC and CLKSC stopped) +25˚C +125˚C +25˚C +125˚C +25˚C +125˚C Value Typ 4 4.5 4 4.7 4 4.7 4.7 5.5 7.5 8 7 7.7 7.5 8.4 8.5 9.5 7.5 8 7 7.7 7.5 8.4 8.5 9.5 Max 6 mA MB96345/346 8 6 mA MB96F345 8.5 6 mA 9 6.7 mA MB96F348T/H/CyB/C 9.7 10 mA MB96345/346 12 9.5 mA MB96F345 12 10 mA 13 11 mA MB96F348T/H/CyB/C 14 9.5 mA MB96345/346 11.5 9 mA MB96F345 11.5 9.5 mA 12.5 10.5 mA MB96F348T/H/CyB/C 13.5 MB96F346/F347/F348Y/ R/Ayy MB96F346/F347/F348Y/ R/Ayy MB96F346/F347/F348Y/ R/Ayy Unit Remarks Power supply current in Sleep modes* ICCSPLL 70 FME-MB96340 rev 10 MB96340 Series (TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V) Parameter Symbol Condition (at TA) +25˚C PLL Sleep mode with CLKS1/2 = CLKP1= 56MHz, CLKP2 = 28MHz (CLKRC and CLKSC stopped. Core voltage at 1.9V) +125˚C +25˚C +125˚C +25˚C +125˚C PLL Sleep mode with CLKS1/2 = 72MHz, CLKP1 = 36MHz, CLKP2 = 18MHz ICCSPLL (CLKRC and CLKSC stopped. Core voltage at 1.9V) PLL Sleep mode with CLKS1/2 = 80MHz, CLKP1 = 40MHz, CLKP2 = 20MHz (CLKRC and CLKSC stopped. Core voltage at 1.9V) PLL Sleep mode with CLKS1/2 = 96MHz, CLKP1= 48MHz, CLKP2 = 24MHz (CLKRC and CLKSC stopped. Core voltage at 1.9V) +25˚C Value Typ 12.5 13 12.5 13.5 13.5 14.5 9.5 Max 16 mA MB96345/346 18 16 mA 19 17 mA MB96F348T/H/CyB/C 20 12.5 mA +125˚C 10.5 15.5 MB96F346/F347/F348Y/ R/Ayy MB96F346/F347/F348Y/ R/Ayy Unit Remarks +25˚C 11 13.5 mA MB96F345 Power supply current in Sleep modes* +125˚C 11.7 16 +25˚C +125˚C +25˚C +125˚C +25˚C 13 13.5 15 16 1.3 1.8 1 1.6 1.3 1.9 16 mA MB96345/346 18 18 mA MB96F348T/H/CyB/C 21 1.8 mA MB96345/346 3.7 1.3 mA MB96F345 3.4 1.8 mA MB96F346/F347/F348 4.6 ICCSMAIN Main Sleep mode with CLKS1/2 = CLKP1/2 = 4MHz (CLKPLL, CLKSC and CLKRC stopped) +125˚C +25˚C +125˚C +25˚C +125˚C FME-MB96340 rev 10 71 MB96340 Series (TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V) Parameter Symbol Condition (at TA) +25˚C RC Sleep mode with CLKS1/2 = CLKP1/2 = 2MHz (CLKMC, CLKPLL and CLKSC stopped) +125˚C +25˚C +125˚C +25˚C +125˚C +25˚C RC Sleep mode with CLKS1/2 = CLKP1/2 = 100kHz, SMCR:LPMSS = 0 (CLKMC, CLKPLL and CLKSC stopped. Voltage regulator in high power mode) Power supply current in Sleep modes* ICCSRCL +25˚C RC Sleep mode with CLKS1/2 = CLKP1/2 = 100kHz, SMCR:LPMSS = 1 (CLKMC, CLKPLL and CLKSC stopped. Voltage regulator in low power mode) +125˚C +25˚C +125˚C +25˚C +125˚C +25˚C Sub Sleep mode with CLKS1/2 = CLKP1/2 = 32kHz (CLKMC, CLKPLL and CLKRC stopped) +125˚C +25˚C +125˚C +25˚C +125˚C 0.05 0.44 0.05 0.56 0.05 0.56 0.04 0.43 0.04 0.54 0.04 0.54 0.14 mA MB96345/346 1.9 0.15 mA MB96F345 2.1 0.15 mA MB96F346/F347/F348 2.9 0.12 mA MB96345/346 1.85 0.12 mA MB96F345 2.1 0.12 mA MB96F346/F347/F348 2.9 +125˚C +25˚C +125˚C +25˚C +125˚C Value Typ 0.8 1.3 0.55 1.1 0.8 1.4 0.3 0.7 0.09 0.59 0.3 0.8 Max 1.4 mA MB96345/346 3.2 1.1 mA MB96F345 3.1 1.4 mA MB96F346/F347/F348 4.2 0.5 mA MB96345/346 2.3 0.2 mA MB96F345 2.2 0.5 mA MB96F346/F347/F348 3.3 Unit Remarks ICCSRCH ICCSSUB 72 FME-MB96340 rev 10 MB96340 Series (TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V) Parameter Symbol Condition (at TA) +25˚C PLL Timer mode with CLKMC = 4MHz, CLKPLL = 48MHz (CLKRC and CLKSC stopped) +125˚C +25˚C +125˚C +25˚C +125˚C +25˚C Main Timer mode with CLKMC = 4MHz, SMCR:LPMSS = 0 (CLKPLL, CLKRC and CLKSC stopped. Voltage regulator in high power mode) ICCTMAIN +25˚C Main Timer mode with CLKMC = 4MHz, SMCR:LPMSS = 1 (CLKPLL, CLKRC and CLKSC stopped. Voltage regulator in low power mode) +125˚C +25˚C +125˚C +25˚C +125˚C 0.08 0.47 0.08 0.6 0.08 0.6 0.15 mA MB96345/346 1.9 0.15 mA MB96F345 2.1 0.15 mA MB96F346/F347/F348 2.9 +125˚C +25˚C +125˚C +25˚C +125˚C Value Typ 1.4 1.9 1.3 1.9 1.5 2.1 0.35 0.7 0.11 0.63 0.35 0.85 Max 1.9 mA MB96345/346 3.9 1.8 mA MB96F345 4 2 mA MB96F346/F347/F348 5 0.5 mA MB96345/346 2.3 0.2 mA MB96F345 2.2 0.5 mA MB96F346/F347/F348 3.3 Unit Remarks ICCTPLL Power supply current in Timer modes* FME-MB96340 rev 10 73 MB96340 Series (TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V) Parameter Symbol Condition (at TA) +25˚C RC Timer mode with CLKRC = 2MHz, SMCR:LPMSS = 0 (CLKMC, CLKPLL and CLKSC stopped. Voltage regulator in high power mode) ICCTRCH +25˚C RC Timer mode with CLKRC = 2MHz, SMCR:LPMSS = 1 (CLKMC, CLKPLL and CLKSC stopped. Voltage regulator in low power mode) Power supply current in Timer modes* RC Timer mode with CLKRC = 100kHz, SMCR:LPMSS = 0 (CLKMC, CLKPLL and CLKSC stopped. Voltage regulator in high power mode) ICCTRCL +25˚C RC Timer mode with CLKRC = 100kHz, SMCR:LPMSS = 1 (CLKMC, CLKPLL and CLKSC stopped. Voltage regulator in low power mode) +125˚C +25˚C +125˚C +25˚C +125˚C 0.03 0.41 0.03 0.53 0.03 0.53 0.1 mA MB96345/346 1.85 0.1 mA MB96F345 2.05 0.1 mA MB96F346/F347/F348 2.85 +125˚C +25˚C +125˚C +25˚C +125˚C +25˚C +125˚C +25˚C +125˚C +25˚C +125˚C 0.07 0.46 0.07 0.6 0.07 0.6 0.3 0.65 0.08 0.58 0.3 0.8 0.15 mA MB96345/346 1.9 0.15 mA MB96F345 2.1 0.15 mA MB96F346/F347/F348 2.9 0.45 mA MB96345/346 2.2 0.15 mA MB96F345 2.1 0.45 mA MB96F346/F347/F348 3.2 +125˚C +25˚C +125˚C +25˚C +125˚C Value Typ 0.35 0.7 0.13 0.63 0.35 0.85 Max 0.5 mA MB96345/346 2.3 0.2 mA MB96F345 2.2 0.5 mA MB96F346/F347/F348 3.3 Unit Remarks 74 FME-MB96340 rev 10 MB96340 Series (TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V) Parameter Symbol Condition (at TA) +25˚C +125˚C Power supply current in Timer modes* ICCTSUB Sub Timer mode with CLKSC = 32kHz (CLKMC, CLKPLL and CLKRC stopped) +25˚C +125˚C +25˚C +125˚C +25˚C +125˚C VRCR:LPMB[2:0] = 110B (Core voltage at 1.8V) +25˚C +125˚C +25˚C Power supply current in Stop Mode +125˚C ICCH +25˚C +125˚C VRCR:LPMB[2:0] = 000B (Core voltage at 1.2V) +25˚C +125˚C +25˚C +125˚C Power supply current for active Low Voltage detector +25˚C Low voltage detector enabled (RCR:LVDE = 1) +125˚C +25˚C +125˚C Power supply current for active Clock modulator Flash Write/ Erase current ICCCLOMO ICCFLASH ICCDFLASH Clock modulator enabled (CMCR:PDX = 1) Current for one Flash module Current for one Data Flash module 0.015 0.3 0.015 0.4 0.015 0.4 5 7 90 100 3 15 10 0.06 mA MB96345/346 1.4 0.06 mA MB96F345 1.5 0.06 mA MB96F346/F347/F348 2.3 10 20 140 µA 150 4.5 40 20 mA mA mA µA µA MB96F345 Must be added to all current above Other devices Must be added to all current above Must be added to all current above Must be added to all current above Must be added to all current above Value Typ 0.035 0.42 0.035 0.53 0.035 0.53 0.02 0.4 0.02 0.52 0.02 0.52 Max 0.1 mA MB96345/346 1.85 0.1 mA MB96F345 2.05 0.1 mA MB96F346/F347/F348 2.85 0.08 mA MB96345/346 1.8 0.08 mA MB96F345 2.0 0.08 mA MB96F346/F347/F348 2.8 Unit Remarks ICCLVD FME-MB96340 rev 10 75 MB96340 Series (TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V) Parameter Input capacitance Symbol CIN Condition (at TA) Value Typ 5 Max 15 Unit pF Remarks Other than C, AVCC, AVSS, AVRH, AVRL, VCC, VSS * The power supply current is measured with a 4MHz external clock connected to the Main oscillator and a 32kHz external clock connected to the Sub oscillator. See chapter “Standby mode and voltage regulator control circuit” of the Hardware Manual for further details about voltage regulator control. 76 FME-MB96340 rev 10 MB96340 Series 4. AC Characteristics Source Clock timing (TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V) Parameter Symbol Pin Value Min 3 Clock frequency fC X0, X1 0 3.5 Typ Max 16 16 16 Unit Remarks MHz When using a crystal oscillator, PLL off MHz MHz When using an opposite phase external clock, PLL off When using a crystal oscillator or opposite phase external clock, PLL on 0 Clock frequency fFCI X0 3.5 32 X0A, X1A Clock frequency fCL X0A 0 0 50 Clock frequency fCR 1 RC clock stabilization time PLL Clock frequency PLL Phase Jitter Input clock pulse width Input clock pulse width - 56 When using a single phase external clock in “Fast Clock Input mode” (not MHz available in MB96F34xY/R/AxA), PLL off When using a single phase external clock in “Fast Clock Input mode” (not MHz available in MB96F34xY/R/AxA), PLL on kHz When using an oscillation circuit kHz kHz kHz MHz When using an opposite phase external clock When using a single phase external clock When using slow frequency of RC oscillator When using fast frequency of RC oscillator Applied after any reset and when activating the RC oscillator. MB96F345: 256 cycles others 64 cycles Permitted VCO output frequency of PLL (CLKVCO) For CLKMC (PLL input clock) ≥ 4MHz, jitter coming from external oscillator, crystal or resonator is not covered Duty ratio is about 30% to 70% 32.768 100 2 56 100 100 50 200 4 tRCSTAB - 64 or 256 RC clock cycles fCLKVCO TPSKEW PWH, PWL X0,X1 64 8 5 - 200 ±5 - MHz ns ns µs PWHL, PWLL X0A,X1A FME-MB96340 rev 10 77 MB96340 Series tCYL VIH X0 PWH PWL VIL tCYLL VIH X0A PWHL PWLL VIL 78 FME-MB96340 rev 10 MB96340 Series Internal Clock timing (TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V) Core Voltage Settings Parameter Internal System clock frequency (CLKS1 and CLKS2) Symbol Min fCLKS1, fCLKS2 0 0 0 0 Internal CPU clock frequency (CLKB), internal peripheral clock frequency (CLKP1) Internal peripheral clock frequency (CLKP2) fCLKB, fCLKP1 0 0 fCLKP2 0 0 1.8V Max 92 86 72 68 52 36 28 26 Min 0 0 0 0 0 0 0 0 1.9V Max 96 96 80 74 56 40 32 28 MHz Others than below Unit Remarks MHz MB96F348T/H/CxB/C MHz MHz MHz MHz MHz MHz MB96F345 MB96F34xY/R/Axx Others than below MB96F345 Others than below MB96F34xY/R/Axx FME-MB96340 rev 10 79 MB96340 Series External Reset timing (TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V) Parameter Reset input time Symbol tRSTL Pin RSTX Value Min 500 Typ Max Unit ns Remarks tRSTL RSTX 0.2 VCC 0.2 VCC 80 FME-MB96340 rev 10 MB96340 Series Power On Reset timing (TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V) Parameter Power on rise time Power off time Symbol tR tOFF Pin Vcc Vcc Value Min 0.05 1 Typ Max 30 Unit ms ms Remarks tR VCC 0.2 V 2.7V 0.2 V tOFF 0.2 V If the power supply is changed too rapidly, a power-on reset may occur. We recommend a smooth startup by restraining voltages when changing the power supply voltage during operation, as shown in the figure below. VCC 3V Rising edge of 50 mV/ms maximum is allowed FME-MB96340 rev 10 81 MB96340 Series External Input timing (TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V) Parameter Symbol Pin INTn(_R) NMI(_R) Pnn_m Input pulse width tINH tINL TINn(_R) TTGn(_R) ADTG(_R) FRCKn(_R) INn(_R) Note : Relocated Resource Inputs have same characteristics ⎯ 2*tCLKP1 + 200 (tCLKP1=1/ fCLKP1) Condition Value Min 200 Max ⎯ Unit ns Used Pin input function External Interrupt NMI General Purpose IO Reload Timer PPG Trigger input ⎯ ns AD Converter Trigger Free Running Timer external clock Input Capture External Pin input VIH VIH VIL tINH tINL VIL 82 FME-MB96340 rev 10 MB96340 Series External Bus timing Note: The values given below are for an I/O driving strength IOdrive = 5mA. If IOdrive is 2mA, all the maximum output timing described in the different tables must then be increased by 10ns. Basic Timing Parameter (TA = −40 °C to +125 °C, VCC = 5.0 V ± 10%, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF) Symbol tCYC Pin Condition Value Min 25 ECLK ⎯ tCYC/2-5 tCYC/2-5 -20 CSn, UBX, LBX, ECLK ⎯ -20 -20 -20 -10 ALE, ECLK ⎯ -10 -10 -10 A[23:16], ECLK AD[15:0], ECLK RDX, WRX, WRLX,WRHX, ECLK ⎯ ⎯ -15 -15 -15 -15 -10 ⎯ -10 -10 -10 Max ⎯ tCYC/2+5 tCYC/2+5 20 20 20 20 10 10 10 10 15 15 15 15 10 10 10 10 ns ns ns ns ns ns Unit Remarks ECLK tCHCL tCLCH tCHCBH ECLK → UBX/ LBX / CSn time tCHCBL tCLCBH tCLCBL tCHLH tCHLL tCLLH tCLLL tCHAV ECLK → ALE time ECLK → address valid time tCLAV tCLADV tCHADV tCHRWH ECLK → RDX /WRX time tCHRWL tCLRWH tCLRWL FME-MB96340 rev 10 83 MB96340 Series (TA = −40 °C to +125 °C, VCC = 3.0 to 4.5V, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF) Parameter Symbol tCYC ECLK tCHCL tCLCH tCHCBH ECLK → UBX/ LBX / CSn time tCHCBL tCLCBH tCLCBL tCHLH ECLK → ALE time tCHLL tCLLH tCLLL tCHAV ECLK → address valid time tCLAV tCLADV tCHADV tCHRWH ECLK → RDX /WRX time tCHRWL tCLRWH tCLRWL RDX, WRX, WRLX, WRHX, ECLK ⎯ A[23:16], ECLK AD[15:0], ECLK ⎯ ⎯ ALE, ECLK ⎯ CSn, UBX, LBX, ECLK ⎯ ECLK ⎯ Pin Condition Value Min 30 tCYC/2-8 tCYC/2-8 -25 -25 -25 -25 -15 -15 -15 -15 -20 -20 -20 -20 -15 -15 -15 -15 Max ⎯ tCYC/2+8 tCYC/2+8 25 25 25 25 15 15 15 15 20 20 20 20 15 15 15 15 ns ns ns ns ns ns Unit Remarks 84 FME-MB96340 rev 10 MB96340 Series tCYC tCHCL ECLK 0.8*Vcc 0.2*Vcc tCHAV A[23:16] tCLAV tCLCH tCHCBL CSn LBX UBX tCLCBH tCLCBL tCHCBH tCHRWL RDX WRX (WRLX, WRHX) tCLRWH tCLRWL tCHRWH tCLLH ALE tCHLL tCHLH tCLLL tCLADV Address tCHADV AD[15:0] Refer to the Hardware Manual for detailed Timing Charts FME-MB96340 rev 10 85 MB96340 Series Bus Timing (Read) Parameter (TA = −40 °C to +125 °C, VCC = 5.0 V ± 10%, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF) Symbol Pin Conditions EACL:STS=0 and EACL:ACE=0 Value Min tCYC/2 − 5 tCYC − 5 3tCYC/2 − 5 tCYC − 15 Max ⎯ ⎯ ⎯ ⎯ ⎯ Unit Remarks ALE pulse width tLHLL ALE EACL:STS=1 EACL:STS=0 and EACL:ACE=1 EACL:STS=0 and EACL:ACE=0 ns tAVLL ALE, A[23:16], EACL:STS=1 and 3tCYC/2 − 15 EACL:ACE=0 EACL:STS=0 and EACL:ACE=1 ns ⎯ ⎯ ⎯ ⎯ ns ⎯ ⎯ ⎯ ⎯ ⎯ ns ⎯ ⎯ ns ⎯ 3tCYC − 55 ns 4tCYC − 55 5tCYC/2 − 55 ns 7tCYC/2 − 55 ⎯ ns w/o cycle extension 2tCYC − 15 Valid address ⇒ ALE ↓ time EACL:STS=1 and 5tCYC/2 − 15 EACL:ACE=1 EACL:STS=0 and EACL:ACE=0 EACL:STS=1 and EACL:ACE=0 tCYC/2 − 15 tCYC − 15 tADVLL ALE,AD[15:0] EACL:STS=0 and 3tCYC/2 − 15 EACL:ACE=1 EACL:STS=1 and EACL:ACE=1 2tCYC − 15 tCYC/2 − 15 -15 3tCYC/2 − 15 5tCYC/2 − 15 tCYC − 15 2tCYC − 15 ⎯ ⎯ ⎯ ⎯ 3 tCYC/2 − 5 ⎯ 0 ALE ↓ ⇒ Address valid time EACL:STS=0 tLLAX ALE, AD[15:0] EACL:STS=1 EACL:ACE=0 ns tAVRL Valid address ⇒ RDX ↓ time RDX, A[23:16] EACL:ACE=1 EACL:ACE=0 tADVRL RDX, AD[15:0] EACL:ACE=1 EACL:ACE=0 tAVDV Valid address ⇒ Valid data input A[23:16], AD[15:0] EACL:ACE=1 EACL:ACE=0 tADVDV AD[15:0] EACL:ACE=1 w/o cycle extension RDX pulse width RDX ↓ ⇒ Valid data input RDX ↑ ⇒ Data hold time 86 tRLRH RDX tRLDV RDX, AD[15:0] tRHDX RDX, AD[15:0] ⎯ ⎯ ⎯ w/o cycle extension w/o cycle extension 3 tCYC/2 − 50 ns ⎯ ns FME-MB96340 rev 10 MB96340 Series (TA = −40 °C to +125 °C, VCC = 5.0 V ± 10%, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF) Parameter Address valid ⇒ Data hold time RDX ↑ ⇒ ALE ↑ time Symbol tAXDX Pin A[23:16], AD[15:0] Conditions ⎯ Value Min 0 Max ⎯ ⎯ ns ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ tCYC − 50 ns ns ns ns Unit ns Remarks tRHLH RDX, ALE tAVCH A[23:16], ECLK tADVCH AD[15:0], ECLK tRLCH RDX, ECLK tLLRL ALE, RDX tCHDV AD[15:0], ECLK EACL:STS=1 and 3tCYC/2 − 10 EACL:ACE=1 other ECL:STS, tCYC/2 − 10 EACL:ACE setting Valid address ⇒ ECLK ↑ time RDX ↓ ⇒ ECLK ↑ time ALE ↓ ⇒ RDX ↓ time ECLK↑ ⇒ Valid data input ⎯ ⎯ EACL:STS=0 EACL:STS=1 tCYC − 15 tCYC/2 − 15 tCYC/2 − 10 tCYC/2 − 10 − 10 ⎯ ⎯ (TA = −40 °C to +125 °C, VCC = 3.0 to 4.5V, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF) Parameter Symbol Pin Conditions EACL:STS=0 and EACL:ACE=0 Value Min tCYC/2 − 8 tCYC − 8 3tCYC/2 − 8 tCYC − 20 Max ⎯ ⎯ ⎯ ⎯ ⎯ Unit Remarks ALE pulse width tLHLL ALE EACL:STS=1 EACL:STS=0 and EACL:ACE=1 EACL:STS=0 and EACL:ACE=0 ns tAVLL ALE, A[23:16], EACL:STS=1 and 3tCYC/2 − 20 EACL:ACE=0 EACL:STS=0 and EACL:ACE=1 ns ⎯ ⎯ ⎯ ⎯ ns ⎯ ⎯ ⎯ ⎯ ns 2tCYC − 20 Valid address ⇒ ALE ↓ time EACL:STS=1 and 5tCYC/2 − 20 EACL:ACE=1 EACL:STS=0 and EACL:ACE=0 EACL:STS=1 and EACL:ACE=0 tCYC/2 − 20 tCYC − 20 tADVLL ALE, AD[15:0] EACL:STS=0 and 3tCYC/2 − 20 EACL:ACE=1 EACL:STS=1 and EACL:ACE=1 2tCYC − 20 tCYC/2 − 20 -20 ALE ↓ ⇒ Address valid time EACL:STS=0 tLLAX ALE, AD[15:0] EACL:STS=1 FME-MB96340 rev 10 87 MB96340 Series (TA = −40 °C to +125 °C, VCC = 3.0 to 4.5V, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF) Parameter Symbol Pin Conditions EACL:ACE=0 Value Min 3tCYC/2 − 20 5tCYC/2 − 20 tCYC − 20 2tCYC − 20 ⎯ ⎯ ⎯ ⎯ 3tCYC/2 − 8 ⎯ 0 0 Max ⎯ Unit Remarks tAVRL Valid address ⇒ RDX ↓ time RDX, A[23:16] EACL:ACE=1 EACL:ACE=0 ns ⎯ ⎯ ns ⎯ 3tCYC − 60 ns 4tCYC − 60 5tCYC/2 − 60 ns 7tCYC/2 − 60 ⎯ ns w/o cycle extension tADVRL RDX, AD[15:0] EACL:ACE=1 EACL:ACE=0 tAVDV Valid address ⇒ Valid data input A[23:16], AD[15:0] EACL:ACE=1 EACL:ACE=0 tADVDV AD[15:0] EACL:ACE=1 w/o cycle extension RDX pulse width RDX ↓ ⇒ Valid data input RDX ↑ ⇒ Data hold time Address valid ⇒ Data hold time RDX ↑ ⇒ ALE ↑ time tRLRH RDX tRLDV RDX, AD[15:0] tRHDX RDX, AD[15:0] tAXDX A[23:16] ⎯ ⎯ ⎯ ⎯ w/o cycle extension w/o cycle extension 3tCYC/2 − 55 ns ⎯ ⎯ ⎯ ns ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ tCYC − 55 ns ns ns ns ns ns tRHLH RDX, ALE tAVCH A[23:16], ECLK tADVCH AD[15:0], ECLK tRLCH RDX, ECLK tLLRL ALE, RDX tCHDV AD[15:0], ECLK EACL:STS=1 and 3tCYC/2 − 15 EACL:ACE=1 other ECL:STS, tCYC/2 − 15 EACL:ACE setting Valid address ⇒ ECLK ↑ time RDX ↓ ⇒ ECLK ↑ time ALE ↓ ⇒ RDX ↓ time ECLK↑ ⇒ Valid data input ⎯ ⎯ EACL:STS=0 EACL:STS=1 tCYC − 20 tCYC/2 − 20 tCYC/2 − 15 tCYC/2 − 15 − 15 ⎯ ⎯ 88 FME-MB96340 rev 10 MB96340 Series tAVCH tADVCH ECLK 0.8*Vcc tRLCH tCHDV tAVLL tADVLL ALE tLHLL tAVRL tADVRL RDX tLLAX tRHLH 0.2*VCC tRLRH tLLRL A[23:16] tRLDV tAVDV tADVDV AD[15:0] Address VIH VIL Read data tRHDX VIH VIL tAXDX Refer to the Hardware Manual for detailed Timing Charts . Bus Timing (Write) Parameter (TA = −40 °C to +125 °C, VCC = 5.0 V ± 10%, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF) Pin WRX, WRLX, WRHX, A[23:16] WRX, WRLX, WRHX, AD[15:0] WRX, WRXL, WRHX WRX, WRLX, WRHX, AD[15:0] Condition EACL:ACE=0 EACL:ACE=1 EACL:ACE=0 EACL:ACE=1 Symbol Value Min 3tCYC/2 − 15 5tCYC/2 − 15 tCYC − 15 2tCYC − 15 tCYC − 5 tCYC − 20 Max ⎯ Unit Remarks tAVWL Valid address ⇒ WRX ↓ time tADVWL ns ⎯ ⎯ ns ⎯ ⎯ ⎯ ns w/o cycle extension w/o cycle extension WRX pulse width Valid data output ⇒ WRX ↑ time tWLWH ⎯ ⎯ tDVWH ns FME-MB96340 rev 10 89 MB96340 Series (TA = −40 °C to +125 °C, VCC = 5.0 V ± 10%, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF) Parameter WRX ↑ ⇒ Data hold time WRX ↑ ⇒ Address valid time Symbol Pin WRX, WRLX, WRHX, AD[15:0] WRX, WRLX, WRHX, A[23:16] WRX, WRLX, WRHX, ALE WRX, WRLX, WRHX, ECLK WRX, WRLX, WRHX, CSn WRX, WRLX, WRHX, CSn Condition Value Min tCYC/2 − 15 Max ⎯ Unit Remarks tWHDX ⎯ ⎯ EBM:ACE=1 and EACL:STS=1 other EBM:ACE and EACL:STS setting ⎯ EACL:ACE=0 ns tWHAX tCYC/2 − 15 2tCYC − 10 tCYC − 10 tCYC/2 − 10 ⎯ ⎯ tCYC/2 − 15 ⎯ ⎯ ⎯ ⎯ 3tCYC/2 − 15 5tCYC/2 − 15 ⎯ ns WRX ↑ ⇒ ALE ↑ time tWHLH ns WRX ↓ ⇒ ECLK ↑ time CSn ⇒ WRX time tWLCH ns tCSLWL ns EACL:ACE=1 WRX ⇒ CSn time tWHCSH ⎯ ns (TA = −40 °C to +125 °C, VCC = 3.0 to 4.5V, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF) Parameter Symbol Pin WRX, WRLX, WRHX, A[23:16] WRX, WRLX, WRHX, AD[15:0] WRX, WRXL, WRHX WRX, WRLX, WRHX, AD[15:0] WRX, WRLX, WRHX, AD[15:0] WRX, WRLX, WRHX, A[23:16] Condition EACL:ACE=0 EACL:ACE=1 EACL:ACE=0 EACL:ACE=1 Value Min 3tCYC/2 − 20 5tCYC/2 − 20 tCYC − 20 2tCYC − 20 tCYC − 8 tCYC − 25 Max ⎯ Unit Remarks tAVWL Valid address ⇒ WRX ↓ time tADVWL ns ⎯ ⎯ ns ⎯ ⎯ ⎯ ns w/o cycle extension w/o cycle extension WRX pulse width Valid data output ⇒ WRX ↑ time WRX ↑ ⇒ Data hold time WRX ↑ ⇒ Address valid time tWLWH ⎯ ⎯ tDVWH ns tWHDX ⎯ ⎯ tCYC/2 − 20 ⎯ ns tWHAX tCYC/2 − 20 ⎯ ns 90 FME-MB96340 rev 10 MB96340 Series (TA = −40 °C to +125 °C, VCC = 3.0 to 4.5V, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF) Parameter Symbol Pin Condition EBM:ACE=1 and EACL:STS=1 other EBM:ACE and EACL:STS setting ⎯ EACL:ACE=0 Value Min 2tCYC − 15 tCYC − 15 tCYC/2 − 15 ⎯ ⎯ tCYC/2 − 20 Max ⎯ ⎯ ⎯ 3tCYC/2 − 20 5tCYC/2 − 20 ⎯ Unit Remarks WRX ↑ ⇒ ALE ↑ time tWHLH WRX, WRLX, WRHX, ALE WRX, WRLX, WRHX, ECLK WRX, WRLX, WRHX, CSn WRX, WRLX, WRHX, CSn ns WRX ↓ ⇒ ECLK ↑ time CSn ⇒ WRX time tWLCH ns tCSLWL ns EACL:ACE=1 WRX ⇒ CSn time tWHCSH ⎯ ns tWLCH 0.8*VCC ECLK tWHLH ALE tAVWL tADVWL WRX (WRLX, WRHX) tWLWH . 0.2*VCC tCSLWL CSn tWHCSH tWHAX A[23:16] tDVWH AD[15:0] tWHDX Address Write data Refer to the Hardware Manual for detailed Timing Charts FME-MB96340 rev 10 91 MB96340 Series Ready Input Timing Parameter RDY setup time RDY hold time (TA = −40 °C to +125 °C, VCC = 5.0 V ± 10%, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF) Pin RDY RDY Test Condition ⎯ Rated Value Min 35 0 Max ⎯ ⎯ Units ns ns Remarks Symbol tRYHS tRYHH (TA = −40 °C to +125 °C, VCC = 3.0 to 4.5V, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF) Parameter RDY setup time RDY hold time Symbol tRYHS tRYHH Pin RDY RDY Test Condition ⎯ Rated Value Min 45 0 Max ⎯ ⎯ Units ns ns Remarks Note : If the RDY setup time is insufficient, use the auto-ready function. ECLK 0.8*VCC tRYHS RDY When WAIT is not used. VIH tRYHH VIH RDY When WAIT is used. VIL Refer to the Hardware Manual for detailed Timing Charts Hold Timing Parameter Pin floating ⇒ HAKX ↓ time (TA = −40 °C to +125 °C, VCC = 5.0 V ± 10%, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF) Symbol tXHAL tHAHV Pin HAKX HAKX Condition ⎯ Value Min Max tCYC − 20 tCYC + 20 tCYC − 20 tCYC + 20 Units ns ns Remarks HAKX ↑ time ⇒ Pin valid time (TA = −40 °C to +125 °C, VCC = 3.0 to 4.5V, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF) Parameter Pin floating ⇒ HAKX ↓ time HAKX ↑ time ⇒ Pin valid time Symbol tXHAL tHAHV Pin HAKX HAKX Condition ⎯ Value Min Max tCYC − 25 tCYC + 25 tCYC − 25 tCYC + 25 Units ns ns Remarks 92 FME-MB96340 rev 10 MB96340 Series HAKX 0.2*VCC tXHAL Each pin 0.8*VCC 0.2*VCC High-Z 0.8*VCC tHAHV Refer to the Hardware Manual for detailed Timing Charts FME-MB96340 rev 10 93 MB96340 Series USART timing WARNING: The values given below are for an I/O driving strength IOdrive = 5mA. If IOdrive is 2mA, all the maximum output timing described in the different tables must then be increased by 10ns. (TA = -40˚C to 125˚C, VCC = 3.0V to 5.5V, VSS = AVSS = 0V, IOdrive = 5mA, CL = 50pF) VCC = AVCC= 4.5V VCC = AVCC= 3.0V to 5.5V to 4.5V Unit Min Max Min Max 4 tCLKP1 -20 Internal Shift Clock Mode N*tCLKP1 - 20 *1 tCLKP1 + 45 0 tCLKP1 + 10 tCLKP1 + 10 ⎯ External Shift Clock Mode tCLKP1/2 + 10 tCLKP1 + 10 ⎯ ⎯ ⎯ +20 ⎯ ⎯ ⎯ ⎯ ⎯ 2 tCLKP1 + 45 ⎯ ⎯ 20 20 4 tCLKP1 -30 N*tCLKP1 30 *1 tCLKP1 + 55 0 tCLKP1 + 10 tCLKP1 + 10 ⎯ tCLKP1/2 + 10 tCLKP1 + 10 ⎯ ⎯ ⎯ +30 ⎯ ⎯ ⎯ ⎯ ⎯ 2 tCLKP1 + 55 ⎯ ⎯ 20 20 ns ns ns ns ns ns ns ns ns ns ns ns Parameter Serial clock cycle time SCK ↓ → SOT delay time SOT → SCK ↑ delay time Valid SIN → SCK ↑ SCK ↑ → Valid SIN hold time Serial clock “L” pulse width Serial clock “H” pulse width SCK ↓ → SOT delay time Valid SIN → SCK ↑ SCK ↑ → Valid SIN hold time SCK fall time SCK rise time Symbol tSCYCI tSLOVI tOVSHI tIVSHI tSHIXI tSLSHE tSHSLE tSLOVE tIVSHE tSHIXE tFE tRE Pin SCKn SCKn, SOTn SCKn, SOTn SCKn, SINn SCKn, SINn SCKn SCKn SCKn, SOTn SCKn, SINn SCKn, SINn SCKn SCKn Condition Notes: • AC characteristic in CLK synchronized mode. • CL is the load capacity value of pins when testing. • Depending on the used machine clock frequency, the maximum possible baud rate can be limited by some parameters. These parameters are shown in “MB96300 Super series HARDWARE MANUAL” • tCLKP1 is the cycle time of the peripheral clock 1 (CLKP1), Unit : ns *1: Parameter N depends on tSCYCI and can be calculated as follows: • if tSCYCI = 2*k*tCLKP1, then N = k, where k is an integer > 2 • if tSCYCI = (2*k+1)*tCLKP1, then N = k+1, where k is an integer > 1 Examples: tSCYCI N 4*tCLKP1 5*tCLKP1, 6*tCLKP1 7*tCLKP1, 8*tCLKP1 ... 94 2 3 4 ... FME-MB96340 rev 10 MB96340 Series tSCYCI SCK for ESCR:SCES = 0 0.8*VCC 0.2*VCC 0.2*VCC SCK for ESCR:SCES = 1 0.8*VCC 0.2*VCC tSLOVI tOVSHI 0.8*VCC 0.2*VCC tIVSHI VIH VIL tSHIXI VIH VIL 0.8*VCC SOT SIN Internal Shift Clock Mode tSLSHE SCK for ESCR:SCES = 0 VIH VIL VIL VIH tSHSLE VIH SCK for ESCR:SCES = 1 tFE VIH VIL tSLOVE VIH VIL tRE VIL SOT 0.8*VCC 0.2*VCC tIVSHE VIH VIL tSHIXE VIH VIL SIN External Shift Clock Mode FME-MB96340 rev 10 95 MB96340 Series I2C Timing (TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V,VSS = AVSS =0V) Parameter SCL clock frequency Hold time (repeated) START condition SDA↓→SCL↓ “L” width of the SCL clock “H” width of the SCL clock Set-up time for a repeated START condition SCL↑→SDA↓ Data hold time SCL↓→SDA↓↑ Data set-up time SDA↓↑→SCL↑ Set-up time for STOP condition SCL↑→SDA↑ Bus free time between a STOP and START condition Output fall time from 0.7*Vcc to 0.3*Vcc with a bus capacitance from 10 pF to 400 pF Capacitive load for each bus line Pulse width of spikes which will be suppressed by input noise filter Symbol fSCL tHDSTA tLOW tHIGH tSUSTA tHDDAT tSUDAT tSUSTO tBUS tof Cb tSP Standard-mode Min 0 4.0 4.7 4.0 4.7 0 250 4.0 4.7 20 + 0.1*Cb *2 ⎯ n/a Max 100 ⎯ ⎯ ⎯ ⎯ 3.45 ⎯ ⎯ ⎯ 250 400 n/a Fast-mode*1 Min 0 0.6 1.3 0.6 0.6 0 100 0.6 1.3 20 + 0.1*Cb *2 ⎯ 0 Max 400 ⎯ ⎯ ⎯ ⎯ 0.9 ⎯ ⎯ ⎯ 250 400 1*tCLKP1*3 Unit kHz µs µs µs µs µs ns µs µs ns pF ns *1 : For use at over 100 kHz, set the peripheral clock 1 to at least 6 MHz. *2 : Cb = capacitance of one bus line in pF. *3 : tCLKP1 is the cycle time of the periperal clock CLKP1. SDA tBUS tLOW SCL tSUDAT tHDSTA tHDSTA tHDDAT tHIGH tSUSTA tSUSTO • VOH = 0.7 * VCC • VOL = 0.3 * VCC • CMOS Hysteresis 0.7/0.3 input selected 96 FME-MB96340 rev 10 MB96340 Series 5. Analog Digital Converter (TA = -40 ˚C to +125 ˚C, 3.0 V ≤ AVRH - AVRL, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V) Parameter Resolution Total error Nonlinearity error Differential nonlinearity error Zero transition voltage Full scale transition voltage Compare time Sampling time Symbol VOT VFST Pin ANn ANn Value Min Typ Max 10 ±3 ± 2.5 ± 1.9 Unit bit LSB LSB LSB V V µs µs µs µs 4.5V ≤ ΑVCC ≤ 5.5V 3.0V ≤ ΑVCC < 4.5V 4.5V ≤ ΑVCC ≤ 5.5V 3.0V ≤ ΑVCC < 4.5V Remarks AVRL - AVRL+ AVRL + 1.5 LSB 0.5 LSB 2.5 LSB AVRH - AVRH - AVRH + 3.5 LSB 1.5 LSB 0.5 LSB 1.0 2.0 0.5 1.2 -1 16,500 +1 Analog input leakage current (during conversion) IAIN ANn -1.2 2.5 0.7 +1.2 AVRH AVcc 0.25 AVCC 5 5 1 5 4 TA ≤ 105 ˚C, µA AVSS, AVRL < VI < AVCC, AVRH 105 ˚C < TA ≤ 125 ˚C, µA AVSS, AVRL < VI < AVCC, AVRH V V V mA A/D Converter active µA A/D Converter not operated Analog input voltage range Reference voltage range VAIN AVRH AVRL IA ANn AVRH/ AVRH2 AVRL AVcc AVcc AVRH/ AVRL AVRH/ AVRL ANn AVRL 0.75 AVcc AVSS - Power supply current IAH IR IRH - Reference voltage current Offset between input channels mA A/D Converter active µA LSB A/D Converter not operated Note: The accuracy gets worse as |AVRH - AVRL| becomes smaller. FME-MB96340 rev 10 97 MB96340 Series Definition of A/D Converter Terms Resolution: Analog variation that is recognized by an A/D converter. Total error : Difference between the actual value and the ideal value. The total error includes zero transition error, full-scale transition error and nonlinearity error. Nonlinearity error: Deviation between a line across zero-transition line (“00 0000 0000” “00 0000 0001”) and full-scale transition line (“11 1111 1110” “11 1111 1111”) and actual conversion characteristics. Differential nonlinearity error: Deviation of input voltage, which is required for changing output code by 1 LSB, from an ideal value. Zero reading voltage: Input voltage which results in the minimum conversion value. Full scale reading voltage: Input voltage which results in the maximum conversion value. Total error 3FF 3FE 3FD Digital output {1 LSB × (N − 1) + 0.5 LSB} Actual conversion characteristics 1.5 LSB 004 003 002 001 0.5 LSB AVRL Analog input VNT (Actually-measured value) Actual conversion characteristics Ideal characteristics AVRH Total error of digital output “N” = VNT − {1 LSB × (N − 1) + 0.5 LSB} 1 LSB AVRH − AVRL 1 LSB = (Ideal value) [V] 1024 [LSB] N: A/D converter digital output value VOT (Ideal value) = AVRL + 0.5 LSB [V] VFST (Ideal value) = AVRH − 1.5 LSB [V] VNT : A voltage at which digital output transitions from (N − 1) to N. 98 FME-MB96340 rev 10 MB96340 Series Nonlinearity error 3FF 3FE 3FD Digital output Actual conversion characteristics {1 LSB × (N − 1) + VOT } N+1 VFST (actual measurement value) VNT (actual measurement value) Actual conversion characteristics Differential nonlinearity error Ideal characteristics Actual conversion characteristics Digital output N 004 003 002 N−1 V (N + 1) T (actual measurement value) VNT (actual measurement value) Actual conversion characteristics AVRH Analog input Ideal characteristics 001 VOT (actual measurement value) AVRL Analog input AVRH N−2 AVRL Nonlinearity error of digital output N = Differential nonlinearity error of digital output N = 1 LSB = VNT − {1 LSB × (N − 1) + VOT} 1 LSB V (N+1) T − VNT 1 LSB VFST − VOT 1022 −1 LSB [LSB] [V] [LSB] N : A/D converter digital output value VOT : Voltage at which digital output transits from “000H” to “001H.” VFST : Voltage at which digital output transits from “3FEH” to “3FFH.” FME-MB96340 rev 10 99 MB96340 Series Accuracy and setting of the A/D Converter sampling time If the external impedance is too high or the sampling time too short, the analog voltage charged to the internal sample and hold capacitor is insufficient, adversely affecting the A/D conversion precision. To satisfy the A/D conversion precision, a sufficient sampling time must be selected. The required sampling time depends on the external driving impedance Rext, the board capacitance of the A/D converter input pin Cext and the AVcc voltage level. The following replacement model can be used for the calculation: MCU Analog input Rext Source Cext CIN CADC RADC Comparator Sampling switch Rext: external driving impedance Cext: capacitance of PCB at A/D converter input CIN: capacitance of MCU input pin: 15pF (max) RADC: resistance within MCU: 2.6kΩ (max) for 4.5V ≤ AVcc ≤ 5.5V 12kΩ (max) for 3.0V ≤ AVcc < 4.5V CADC: sampling capacitance within MCU: 10pF (max) The sampling time should be set to minimum “7τ“. The following approximation formula for the replacement model above can be used: Tsamp [min] = 7 × (Rext × (Cext + CIN) + (Rext + RADC) × CADC) • Do not select a sampling time below the absolute minimum permitted value (0.5µs for 4.5V ≤ AVcc ≤ 5.5V; 1.2 µs for 3.0V ≤ AVcc < 4.5V). • If the sampling time cannot be sufficient, connect a capacitor of about 0.1 µF to the analog input pin. In this case the internal sampling capacitance CADC will be charged out of this external capacitance. • A big external driving impedance also adversely affects the A/D conversion precision due to the pin input leakage current IIL (static current before the sampling switch) or the analog input leakage current IAIN (total leakage current of pin input and comparator during sampling). The effect of the pin input leakage current IIL cannot be compensated by an external capacitor. • The accuracy gets worse as |AVRH - AVRL| becomes smaller. 100 FME-MB96340 rev 10 MB96340 Series 6. Alarm Comparator (TA = -40 ˚C to +125 ˚C, VCC = AVCC = 3.0V - 5.5V, VSS = AVSS = 0V) Parameter Symbol Pin Value Min AVCC Typ 25 Max 45 Unit µA Remarks Alarm comparator enabled in fast mode (one channel) Alarm comparator enabled in slow mode (one channel) Alarm comparator disabled IA5ALMF Power supply current IA5ALMS IA5ALMH -1 -3 0 7 - 13 5 +1 +3 AVCC - µA µA ALARM pin input current ALARM pin input voltage range External low threshold high->low transition External low threshold low->high transition External high threshold high->low transition External high threshold low->high transition Internal low threshold high->low transition Internal low threshold low->high transition Internal high threshold high->low transition Internal high threshold low->high transition Switching hysteresis Comparison time Power-up stabilization time after enabling alarm comparator Slow/Fast mode transition time IALIN VALIN VEVTL(H->L) VEVTL(L->H) VEVTH(H->L) VEVTH(L->H) VIVTL(H->L) VIVTL(L->H) VIVTH(H->L) VIVTH(L->H) VHYS tCOMPF tCOMPS tPD tCMD µA TA = 25 ˚C µA TA = 125 ˚C V V V INTREF = 0 V V V V INTREF = 1 V V mV µs µs ms µs CMD = 1 (fast) CMD = 0 (slow) Threshold levels specified above are not guaranteed within this time 0.36 * AVCC 0.36 * AVCC -0.25 -0.1 - 0.36 * AVCC 0.36 * AVCC +0.1 +0.25 - 0.78 * AVCC 0.78 * AVCC -0.25 -0.1 0.78 * AVCC 0.78 * AVCC +0.1 +0.25 ALARM0, ALARM1 0.9 2.2 50 1.1 1.3 2.4 2.6 0.1 1 1 100 1.55 2.85 300 1 10 10 500 FME-MB96340 rev 10 101 MB96340 Series Comparator Output H L VxVTx(H->L) VxVTx(L->H) VHYS VALIN 102 FME-MB96340 rev 10 MB96340 Series 7. Low Voltage Detector characteristics (TA = -40 ˚C to +125 ˚C, Vcc = AVcc = 3.0V - 5.5V, Vss = AVss = 0V) Parameter Stabilization time Level 0 Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 Level 8 Level 9 Level 10 Level 11 Level 12 Level 13 Level 14 Level 15 Symbol TLVDSTAB VDL0 VDL1 VDL2 VDL3 VDL4 VDL5 VDL6 VDL7 VDL8 VDL9 VDL10 VDL11 VDL12 VDL13 VDL14 VDL15 Value *1 Min 2.7 2.9 3.1 3.5 3.6 3.7 3.8 3.9 4.0 4.1 Max 75 2.9 3.1 3.3 3.75 3.85 3.95 4.05 4.15 4.25 4.35 Value *2 Min 2.5 2.8 3 3.35 3.5 3.6 3.7 3.8 3.9 3.95 Max 110 2.9 3.2 3.4 3.8 3.95 4.1 4.2 4.3 4.4 4.5 Unit µs V V V V V V V V V V Remarks After power-up or change of detection level CILCR:LVL[3:0]=”0000” CILCR:LVL[3:0]=”0001” CILCR:LVL[3:0]=”0010” CILCR:LVL[3:0]=”0011” CILCR:LVL[3:0]=”0100” CILCR:LVL[3:0]=”0101” CILCR:LVL[3:0]=”0110” CILCR:LVL[3:0]=”0111” CILCR:LVL[3:0]=”1000” CILCR:LVL[3:0]=”1001” not used not used not used not used not used not used not used not used 2.6 3 V CILCR:LVL[3:0]=”1100” not used not used not used *1: valid for all devices except devices listed under “*2” *2: valid for: MB96F345 CILCR:LVL[3:0] are the low voltage detector level select bits of the CILCR register. V For correct detection, the slope of the voltage level must satisfy dV ≤ 0.004 ----- . Faster variations are regarded as noise and may not be detected. dt µs The functional operation of the MCU is guaranteed down to the minimum low voltage detection level of “Level 0” (VDL0_MIN). The electrical characteristics however are only valid in the specified range (usually down to 3.0V). FME-MB96340 rev 10 103 MB96340 Series Low Voltage Detector Operation In the following figure, the occurrence of a low voltage condition is illustrated. For a detailed description of the reset and startup behavior, please refer to the corresponding hardware manual chapter. Voltage [V] VCC VDLx, Max VDLx, Min dV dt Time [s] Normal Operation Low Voltage Reset Assertion Power Reset Extension Time 104 FME-MB96340 rev 10 MB96340 Series 8. FLASH memory program/erase characteristics (TA = -40˚C to 105˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V) Parameter Sector erase time Program/Data Flash (Main Flash) Sector erase time Data Flash Chip erase time Program/Data Flash (Main Flash) Chip erase time Data Flash Word (16-bit width) programming time Program/Data Flash (Main Flash) Byte (8-bit width) programming time Data Flash Program/Erase cycle Flash data retention time Value Min Typ 0.9 0.5 0.8 n*0.9 2.5 3.7 23 Max 3.6 2 3.6 n*3.6 10 16.4 370 Unit Remarks Without erasure pre-programming time Without erasure pre-programming time Including erasure pre-programming time Without erasure pre-programming time (n is the number of Flash sector of the device) Without erasure pre-programming time Including erasure pre-programming time Without overhead time for submitting write command Without overhead time for submitting write command 100 000 Program/Erase cycles are under evaluation by Fujitsu Microelectronics *1 s s s s s s us - 15 100 us 10 000 20 - - cycle year *1: This value was converted from the results of evaluating the reliability of the technology (using Arrhenius equation to convert high temperature measurements into normalized value at 85oC) FME-MB96340 rev 10 105 MB96340 Series ■ EXAMPLE CHARACTERISTICS 1. Temperature dependency of power supply currents The following diagrams show the current consumption of samples with typical wafer process parameters in different operation modes. Common condition for all operation modes: • VCC = AVCC = 5.0V • Main clock = 4MHz external clock • Sub clock = 32kHz external clock Operation mode details: Mode name PLL Run 56 Details PLL Run mode current ICCPLL with the following settings: • fCLKS1 = fCLKS2 = fCLKB = fCLKP1 = 56MHz • fCLKP2 = 28MHz • Regulator in High Power Mode • Core voltage at 1.9V (VRCR:HPM[1:0] = 11B) • 2 Flash/ROM wait states (MTCRA=233AH) • RC oscillator and Sub oscillator stopped PLL Run mode current ICCPLL with the following settings: • fCLKS1 = fCLKS2 = 96MHz • fCLKB = fCLKP1 = 48MHz • fCLKP2 = 24MHz • Regulator in High Power Mode • Core voltage at 1.9V (VRCR:HPM[1:0] = 11B) • 1 Flash/ROM wait states (MTCRA=6B09H) • RC oscillator and Sub oscillator stopped PLL Run mode current ICCPLL with the following settings: • fCLKS1 = fCLKS2 = 80MHz • fCLKB = fCLKP1 = 40MHz • fCLKP2 = 20MHz • Regulator in High Power Mode • Core voltage at 1.9V (VRCR:HPM[1:0] = 11B) • 1 Flash/ROM wait states (MTCRA=6B09H) • RC oscillator and Sub oscillator stopped PLL Run mode current ICCPLL with the following settings: • fCLKS1 = fCLKS2 = 72MHz • fCLKB = fCLKP1 = 36MHz • fCLKP2 = 18MHz • Regulator in High Power Mode • Core voltage at 1.9V (VRCR:HPM[1:0] = 11B) • 1 Flash/ROM wait states (MTCRA=6B09H) • RC oscillator and Sub oscillator stopped PLL Run 48 PLL Run 40 PLL Run 36 106 FME-MB96340 rev 10 MB96340 Series Mode name PLL Run 24 Details PLL Run mode current ICCPLL with the following settings: • fCLKS1 = fCLKS2 = 48MHz • fCLKB = fCLKP1 = fCLKP2 = 24MHz • Regulator in High Power Mode • Core voltage at 1.8V (VRCR:HPM[1:0] = 10B) • 0 Flash/ROM wait states (MTCRA=2208H) • RC oscillator and Sub oscillator stopped Main Run mode current ICCMAIN with the following settings: • fCLKS1 = fCLKS2 = fCLKB = fCLKP1 = fCLKP2 = 4MHz • Regulator in High Power Mode • Core voltage at 1.8V (VRCR:HPM[1:0] = 10B) • 1 Flash/ROM wait states (MTCRA=0239H) • PLL, RC oscillator and Sub oscillator stopped RC Run mode current ICCRCH with the following settings: • RC oscillator set to 2MHz (CKFCR:RCFS = 1) • fCLKS1 = fCLKS2 = fCLKB = fCLKP1 = fCLKP2 = 2MHz • Regulator in High Power Mode • Core voltage at 1.8V (VRCR:HPM[1:0] = 10B) • 1 Flash/ROM wait states (MTCRA=0239H) • PLL, Main oscillator and Sub oscillator stopped RC Run mode current ICCRCL with the following settings: • RC oscillator set to 100kHz (CKFCR:RCFS = 0) • fCLKS1 = fCLKS2 = fCLKB = fCLKP1 = fCLKP2 = 100kHz • Regulator in Low Power Mode A (SMCR:LPMS = 1) • Core voltage at 1.8V (VRCR:LPMA[2:0] = 110B) • 1 Flash/ROM wait states (MTCRA=0239H) • PLL, Main oscillator and Sub oscillator stopped Sub Run mode current ICCSUB with the following settings: • fCLKS1 = fCLKS2 = fCLKB = fCLKP1 = fCLKP2 = 32kHz • Regulator in Low Power Mode A (by hardware) • Core voltage at 1.8V (VRCR:LPMA[2:0] = 110B) • 1 Flash/ROM wait states (MTCRA=0239H) • PLL, RC oscillator and Main oscillator stopped PLL Sleep mode current ICCSPLL with the following settings: • fCLKS1 = fCLKS2 = fCLKP1 = 56MHz • fCLKP2 = 28MHz • Regulator in High Power Mode • Core voltage at 1.9V (VRCR:HPM[1:0] = 11B) • RC oscillator and Sub oscillator stopped Main Run RC Run 2M RC Run 100k Sub Run PLL Sleep 56 FME-MB96340 rev 10 107 MB96340 Series Mode name PLL Sleep 48 Details PLL Sleep mode current ICCSPLL with the following settings: • fCLKS1 = fCLKS2 = 96MHz • fCLKP1 = 48MHz • fCLKP2 = 24MHz • Regulator in High Power Mode • Core voltage at 1.9V (VRCR:HPM[1:0] = 11B) • RC oscillator and Sub oscillator stopped PLL Sleep mode current ICCSPLL with the following settings: • fCLKS1 = fCLKS2 = 80MHz • fCLKP1 = 40MHz • fCLKP2 = 20MHz • Regulator in High Power Mode • Core voltage at 1.9V (VRCR:HPM[1:0] = 11B) • RC oscillator and Sub oscillator stopped PLL Sleep mode current ICCSPLL with the following settings: • fCLKS1 = fCLKS2 = 72MHz • fCLKP1 = 36MHz • fCLKP2 = 18MHz • Regulator in High Power Mode • Core voltage at 1.9V (VRCR:HPM[1:0] = 11B) • RC oscillator and Sub oscillator stopped PLL Sleep mode current ICCSPLL with the following settings: • fCLKS1 = fCLKS2 = 48MHz • fCLKP1 = fCLKP2 = 24MHz • Regulator in High Power Mode • Core voltage at 1.8V (VRCR:HPM[1:0] = 10B) • RC oscillator and Sub oscillator stopped Main Sleep mode current ICCSMAIN with the following settings: • fCLKS1 = fCLKS2 = fCLKP1 = fCLKP2 = 4MHz • Regulator in High Power Mode • Core voltage at 1.8V (VRCR:HPM[1:0] = 10B) • PLL, RC oscillator and Sub oscillator stopped RC Sleep mode current ICCSRCH with the following settings: • RC oscillator set to 2MHz (CKFCR:RCFS = 1) • fCLKS1 = fCLKS2 = fCLKP1 = fCLKP2 = 2MHz • Regulator in High Power Mode • Core voltage at 1.8V (VRCR:HPM[1:0] = 10B) • PLL, Main oscillator and Sub oscillator stopped RC Sleep mode current ICCSRCL with the following settings: • RC oscillator set to 100kHz (CKFCR:RCFS = 0) • fCLKS1 = fCLKS2 = fCLKP1 = fCLKP2 = 100kHz • Regulator in Low Power Mode A (SMCR:LPMSS = 1) • Core voltage at 1.8V (VRCR:LPMA[2:0] = 110B) • PLL, Main oscillator and Sub oscillator stopped PLL Sleep 40 PLL Sleep 36 PLL Sleep 24 Main Sleep RC Sleep 2M RC Sleep 100k 108 FME-MB96340 rev 10 MB96340 Series Mode name Sub Sleep Details Sub Sleep mode current ICCSSUB with the following settings: • fCLKS1 = fCLKS2 = fCLKP1 = fCLKP2 = 32kHz • Regulator in Low Power Mode A (by hardware) • Core voltage at 1.8V (VRCR:LPMA[2:0] = 110B) • PLL, RC oscillator and Main oscillator stopped PLL Timer mode current ICCTPLL with the following settings: • fCLKS1 = fCLKS2 = 48MHz • Regulator in High Power Mode • Core voltage at 1.8V (VRCR:HPM[1:0] = 10B) • RC oscillator and Sub oscillator stopped Main Timer mode current ICCTMAIN with the following settings: • fCLKS1 = fCLKS2 = 4MHz • Regulator in Low Power Mode A (SMCR:LPMSS = 1) • Core voltage at 1.8V (VRCR:LPMA[2:0] = 110B) • PLL, RC oscillator and Sub oscillator stopped RC Timer mode current ICCTRCH with the following settings: • RC oscillator set to 2MHz (CKFCR:RCFS = 1) • fCLKS1 = fCLKS2 = 2MHz • Regulator in Low Power Mode A (SMCR:LPMSS = 1) • Core voltage at 1.8V (VRCR:LPMA[2:0] = 110B) • PLL, Main oscillator and Sub oscillator stopped RC Timer mode current ICCTRCL with the following settings: • RC oscillator set to 100kHz (CKFCR:RCFS = 0) • fCLKS1 = fCLKS2 = 100kHz • Regulator in Low Power Mode A (SMCR:LPMSS = 1) • Core voltage at 1.8V (VRCR:LPMA[2:0] = 110B) • PLL, Main oscillator and Sub oscillator stopped Sub Timer mode current ICCTSUB with the following settings: • fCLKS1 = fCLKS2 = 32kHz • Regulator in Low Power Mode A (by hardware) • Core voltage at 1.8V (VRCR:LPMA[2:0] = 110B) • PLL, RC oscillator and Main oscillator stopped Stop mode current ICCH with the following settings: • Regulator in Low Power Mode B (by hardware) • Core voltage at 1.8V (VRCR:LPMB[2:0] = 110B) Stop mode current ICCH with the following settings: • Regulator in Low Power Mode B (by hardware) • Core voltage at 1.2V (VRCR:LPMB[2:0] = 000B) PLL Timer 48 Main Timer RC Timer 2M RC Timer 100k Sub Timer Stop 1.8V Stop 1.2V FME-MB96340 rev 10 109 MB96340 Series MB96345/346 PLL Run and Sleep mode currents 25 PLL Run 48 PLL Run 56 20 15 Icc[mA] 10 5 0 PLL Run 24 PLL Sleep 48 PLL Sleep 56 PLL Sleep 24 -60 -40 -20 0 20 40 60 80 100 120 Ta [˚C] MB96345/346 operation modes with medium currents 3 2.5 Main Run 2 RC Run 2M Icc[mA] 1.5 Main Sleep 1 PLL Timer 48 RC Sleep 2M 0.5 0 -60 -40 -20 0 20 40 60 80 100 120 Ta [˚C] 110 FME-MB96340 rev 10 MB96340 Series MB96345/346 Low power mode currents 1 Icc[mA] 0.1 Main Timer RC Run 100k RC Timer 2M RC Sleep 100k Sub Run Sub Sleep Sub Timer RC Timer 100k Stop 1.8V Stop 1.2V 0.01 -60 -40 -20 0 20 40 60 80 100 120 Ta [˚C] MB96F345 PLL Run and Sleep mode currents 40 PLL Run 40 30 PLL Run 24 20 Icc[mA] PLL Sleep 40 10 PLL Sleep 24 0 -60 -40 -20 0 20 40 60 80 100 120 Ta [˚C] FME-MB96340 rev 10 111 MB96340 Series MB96F345 operation modes with medium currents 5 4 Main Run 3 Icc[mA] RC Run 2M 2 PLL Timer 48 1 Main Sleep RC Sleep 2M 0 -60 -40 -20 0 20 40 60 80 100 120 Ta [˚C] MB96F345 Low power mode currents 1 RC Run 100k 0.1 Sub Run Main Timer RC Timer 2M Icc[mA] 0.01 Sub Sleep RC Sleep 100k Sub Timer RC Timer 100k Stop 1.8V Stop 1.2V 0.001 -60 -40 -20 0 20 40 60 80 100 120 Ta [˚C] 112 FME-MB96340 rev 10 MB96340 Series MB96F346/F347/F348Y/R/A PLL Run and Sleep mode currents 50 PLL Run 56 40 PLL Run 36 30 PLL Run 24 Icc[mA] 20 PLL Sleep 56 10 PLL Sleep 36 PLL Sleep 24 0 -60 -40 -20 0 20 40 60 80 100 120 Ta [˚C] MB96F346/F347/F348Y/R/A operation modes with medium currents 5 Main Run 4 Icc[mA] 3 RC Run 2M 2 PLL Timer 48 Main Sleep 1 RC Sleep 2M 0 -60 -40 -20 0 20 40 60 80 100 120 Ta [˚C] FME-MB96340 rev 10 113 MB96340 Series MB96F346/F347/F348Y/R/A Low power mode currents 1 Icc[mA] RC Run 100k 0.1 Sub Run RC Timer 2M Main Timer RC Sleep 100k Sub Sleep Sub Timer RC Timer 100k Stop 1.8V 0.01 -60 Stop 1.2V -40 -20 0 20 40 60 80 100 120 Ta [˚C] MB96F348T/H/C PLL Run and Sleep mode currents 50 PLL Run 48 PLL Run 56 40 30 PLL Run 24 Icc[mA] 20 PLL Sleep 48 PLL Sleep 56 10 PLL Sleep 24 0 -60 -40 -20 0 20 40 60 80 100 120 Ta [˚C] 114 FME-MB96340 rev 10 MB96340 Series MB96F348T/H/C operation modes with medium currents 6 5 Main Run 4 Icc[mA] 3 RC Run 2M 2 PLL Timer 48 Main Sleep 1 RC Sleep 2M 0 -60 -40 -20 0 20 40 60 80 100 120 Ta [˚C] MB96F348T/H/C Low power mode currents 1 RC Run 100k 0.1 Sub Run Main Timer RC Timer 2M Icc[mA] RC Sleep 100k Sub Sleep Sub Timer RC Timer 100k 0.01 Stop 1.8V Stop 1.2V 0.001 -60 -40 -20 0 20 40 60 80 100 120 Ta [˚C] FME-MB96340 rev 10 115 MB96340 Series 2. Frequency dependency of power supply currents in PLL Run mode The following diagrams show the current consumption of samples with typical wafer process parameters in PLL Run mode at different frequencies and Flash timing settings. Measurement conditions: • VCC = AVCC = 5.0V • Ta = 25˚C • fCLKS1 = fCLKB or fCLKS1 = 2*fCLKB as described in diagram • fCLKS2 = fCLKS1 • fCLKP1 = fCLKB • fCLKP2 = fCLKB/2 • Core voltage at 1.8V (VRCR:HPM[1:0] = 10B) or 1.9V (VRCR:HPM[1:0] = 11B) as described in diagram • Main clock = 4MHz external clock • Flash memory timing settings: • MTCRA=2128H/2208H (0 Flash wait states, fCLKS1 = 2*fCLKB) • MTCRA=0239H/2129H (1 Flash wait state, fCLKS1 = fCLKB) • MTCRA=4C09H/6B09H (1 Flash wait state, fCLKS1 = 2*fCLKB) • MTCRA=233AH (2 Flash wait states, fCLKS1 = fCLKB) • Average Flash access rate (number of read accesses to the Flash per CLKB clock cycle, no buffer hit): • 0 Flash wait states: 0.5 • 1 Flash wait states: 0.33 • 2 Flash wait states: 0.25 MB96F345 PLL Run mode currents 40 1 Flash wait state (CLKS1=2*CLKB, 1.9V) 35 1 Flash wait state (CLKS1=2*CLKB, 1.8V) 30 25 ICCPLL (mA) 0 Flash wait states (CLKS1=2*CLKB, 1.8V) 2 Flash wait states (CLKS1=CLKB, 1.9V) 20 2 Flash wait states (CLKS1=CLKB, 1.8V) 15 10 1 Flash wait state (CLKS1=CLKB, 1.8V) : Specified in "DC characteristics" 5 0 0 4 8 12 16 20 CLKB/CLKP1 (MHz) 24 28 32 36 40 116 FME-MB96340 rev 10 MB96340 Series MB96F346/F347/F348Y/R/A PLL Run mode currents 50 2 Flash wait states (CLKS1=CLKB, 1.9V) 45 1 Flash wait state (CLKS1=2*CLKB, 1.9V) 40 1 Flash wait state (CLKS1=2*CLKB, 1.8V) 35 30 ICCPLL (mA) 25 0 Flash wait states (CLKS1=2*CLKB, 1.8V) 2 Flash wait states (CLKS1=CLKB, 1.8V) 20 15 1 Flash wait state (CLKS1=CLKB, 1.8V) 10 : Specified in "DC characteristics" 5 0 0 4 8 12 16 20 24 28 32 36 40 44 48 52 56 CLKB/CLKP1 (MHz) MB96F348T/H/C PLL Run mode currents 50 1 Flash wait state (CLKS1=2*CLKB, 1.9V) 45 2 Flash wait states (CLKS1=CLKB, 1.9V) 40 1 Flash wait state (CLKS1=2*CLKB, 1.8V) 35 30 ICCPLL (mA) 25 0 Flash wait states (CLKS1=2*CLKB, 1.8V) 2 Flash wait states (CLKS1=CLKB, 1.8V) 20 15 1 Flash wait state (CLKS1=CLKB, 1.8V) 10 : Specified in "DC characteristics" 5 0 0 4 8 12 16 20 24 28 32 36 40 44 48 52 56 CLKB/CLKP1 (MHz) FME-MB96340 rev 10 117 MB96340 Series ■ PACKAGE DIMENSION MB96(F)34x LQFP 100P 100-pin plastic LQFP Lead pitch Package width × package length Lead shape Sealing method Mounting height Weight 0.50 mm 14.0 mm × 14.0 mm Gullwing Plastic mold 1.70 mm Max 0.65 g P-LFQFP100-14×14-0.50 (FPT-100P-M20) Code (Reference) 100-pin plastic LQFP (FPT-100P-M20) 16.00±0.20(.630±.008)SQ Note 1) * : These dimensions do not include resin protrusion. Note 2) Pins width and pins thickness include plating thickness. Note 3) Pins width do not include tie bar cutting remainder. * 14.00±0.10(.551±.004)SQ 75 51 76 50 0.08(.003) Details of "A" part INDEX 1.50 –0.10 .059 –.004 (Mounting height) 26 +0.20 +.008 100 0.10±0.10 (.004±.004) (Stand off) 0.25(.010) 0˚~8˚ "A" (0.50(.020)) 0.60±0.15 (.024±.006) 1 25 0.50(.020) 0.20±0.05 (.008±.002) 0.08(.003) M 0.145±0.055 (.0057±.0022) ©2005-2008 FUJITSU MICROELECTRONICS LIMITED F100031S-c-2-2 C 2005 FUJITSU LIMITED F100031S-c-2-1 Dimensions in mm (inches). Note: The values in parentheses are reference values Please check the latest package dimension at the following URL. http://edevice.fujitsu.com/package/en-search/ 118 FME-MB96340 rev 10 MB96340 Series ■ PACKAGE DIMENSION MB96(F)34x QFP 100P 100-pin plastic QFP Lead pitch Package width × package length Lead shape Sealing method Mounting height Code (Reference) 0.65 mm 14.00 mm × 20.00 mm Gullwing Plastic mold 3.35 mm MAX P-QFP100-14×20-0.65 (FPT-100P-M22) 100-pin plastic QFP (FPT-100P-M22) 23.90±0.40(.941±.016) * 20.00±0.20(.787±.008) 80 51 Note 1) * : These dimensions do not include resin protrusion. Note 2) Pins width and pins thickness include plating thickness. Note 3) Pins width do not include tie bar cutting remainder. 81 50 0.10(.004) 17.90±0.40 (.705±.016) *14.00±0.20 (.551±.008) INDEX Details of "A" part 100 31 1 30 0.25(.010) +0.35 3.00 –0.20 +.014 .118 –.008 (Mounting height) 0~8° 0.17±0.06 (.007±.002) 0.80±0.20 (.031±.008) 0.88±0.15 (.035±.006) 0.25±0.20 (.010±.008) (Stand off) 0.65(.026) 0.32±0.05 (.013±.002) 0.13(.005) M "A" C 2006-2008 FUJITSU MICROELECTRONICS LIMITED F100033S-c-1-2 Dimensions in mm (inches). Note: The values in parentheses are reference values. Please check the latest package dimension at the following URL. http://edevice.fujitsu.com/package/en-search/ FME-MB96340 rev 10 119 MB96340 Series ■ ORDERING INFORMATION MCU with CAN controller Part number MB96345YSA PQC-GSE2 *1 MB96345RSA PQC-GSE2 *1 MB96345YWA PQC-GSE2 MB96345RWA PQC-GSE2 *1 *1 Flash/ROM Subclock Persistent Low Voltage Reset Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Package No Yes ROM (160KB) No Yes No Yes ROM (288KB) No Yes No Yes Flash A (160KB) Data Flash A (64KB) No Yes 100 pin Plastic QFP (FPT-100P-M22) MB96345YSA PMC-GSE2 *1 MB96345RSA PMC-GSE2 *1 MB96345YWA PMC-GSE2 MB96345RWA PMC-GSE2 *1 *1 100 pin Plastic LQFP (FPT-100P-M20) MB96346YSA PQC-GSE2 *1 MB96346RSA PQC-GSE2 *1 MB96346YWA PQC-GSE2 MB96346RWA PQC-GSE2 *1 *1 100 pin Plastic QFP (FPT-100P-M22) MB96346YSA PMC-GSE2 *1 MB96346RSA PMC-GSE2 *1 MB96346YWA PMC-GSE2 MB96346RWA PMC-GSE2 *1 *1 100 pin Plastic LQFP (FPT-100P-M20) MB96F345FSB PQC-GSE2 *1 MB96F345DSB PQC-GSE2 *1 MB96F345FWB PQC-GSE2 MB96F345DWB PQC-GSE2 *1 *1 100 pin Plastic QFP (FPT-100P-M22) MB96F345FSB PMC-GSE2 *1 MB96F345DSB PMC-GSE2 *1 MB96F345FWB PMC-GSE2 MB96F345DWB PMC-GSE2 *1 *1 100 pin Plastic LQFP (FPT-100P-M20) 120 FME-MB96340 rev 10 MB96340 Series MCU with CAN controller Part number MB96F346YSB PQC-GSE2 MB96F346RSB PQC-GSE2 MB96F346YWB PQC-GSE2 MB96F346RWB PQC-GSE2 MB96F346YSB PMC-GSE2 MB96F346RSB PMC-GSE2 MB96F346YWB PMC-GSE2 MB96F346RWB PMC-GSE2 MB96F346YSC PQC-GSE2 *1 *1 Flash/ROM Subclock Persistent Low Voltage Reset Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Package No Yes No Yes Flash A (288KB) No Yes No Yes No Yes No Yes Flash A (416KB) No Yes No Yes 100 pin Plastic QFP (FPT-100P-M22) 100 pin Plastic LQFP (FPT-100P-M20) MB96F346RSC PQC-GSE2 100 pin Plastic QFP (FPT-100P-M22) MB96F346YWC PQC-GSE2*1 MB96F346RWC PQC-GSE2*1 MB96F346YSC PMC-GSE2 *1 *1 MB96F346RSC PMC-GSE2 100 pin Plastic LQFP (FPT-100P-M20) MB96F346YWC PMC-GSE2*1 MB96F346RWC PMC-GSE2*1 MB96F347YSB PQC-GSE2 MB96F347RSB PQC-GSE2 MB96F347YWB PQC-GSE2 MB96F347RWB PQC-GSE2 MB96F347YSB PMC-GSE2 MB96F347RSB PMC-GSE2 MB96F347YWB PMC-GSE2 MB96F347RWB PMC-GSE2 MB96F347YSC PQC-GSE2 *1 *1 100 pin Plastic QFP (FPT-100P-M22) 100 pin Plastic LQFP (FPT-100P-M20) MB96F347RSC PQC-GSE2 MB96F347YWC PQC-GSE2*1 MB96F347RWC PQC-GSE2*1 MB96F347YSC PMC-GSE2 *1 *1 100 pin Plastic QFP (FPT-100P-M22) MB96F347RSC PMC-GSE2 MB96F347YWC PMC-GSE2*1 MB96F347RWC PMC-GSE2*1 100 pin Plastic LQFP (FPT-100P-M20) FME-MB96340 rev 10 121 MB96340 Series MCU with CAN controller Part number MB96F348YSB PQC-GSE2 MB96F348RSB PQC-GSE2 MB96F348YWB PQC-GSE2 MB96F348RWB PQC-GSE2 MB96F348YSB PMC-GSE2 MB96F348RSB PMC-GSE2 MB96F348YWB PMC-GSE2 MB96F348RWB PMC-GSE2 MB96F348YSC PQC-GSE2 *1 *1 Flash/ROM Subclock Persistent Low Voltage Reset Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No No Package No Yes No Yes Flash A (544KB) No Yes No Yes No Yes Flash A (544KB) Flash B (32KB) No Yes Emulated by ext. RAM Yes 100 pin Plastic QFP (FPT-100P-M22) 100 pin Plastic LQFP (FPT-100P-M20) MB96F348RSC PQC-GSE2 MB96F348YWC PQC-GSE2*1 MB96F348RWC PQC-GSE2*1 MB96F348YSC PMC-GSE2 *1 *1 100 pin Plastic QFP (FPT-100P-M22) MB96F348RSC PMC-GSE2 MB96F348YWC PMC-GSE2*1 MB96F348RWC PMC-GSE2*1 MB96F348TSC PQC-GSE2 MB96F348HSC PQC-GSE2 MB96F348TWC PQC-GSE2 MB96F348HWC PQC-GSE2 MB96F348TSC PMC-GSE2 MB96F348HSC PMC-GSE2 MB96F348TWC PMC-GSE2 MB96F348HWC PMC-GSE2 MB96V300BRB-ES (for evaluation) 100 pin Plastic LQFP (FPT-100P-M20) 100 pin Plastic QFP (FPT-100P-M22) 100 pin Plastic LQFP (FPT-100P-M20) 416 pin Plastic BGA (BGA-416P-M02) 122 FME-MB96340 rev 10 MB96340 Series MCU without CAN controller Part number MB96F346ASB PQC-GSE2 MB96F346AWB PQC-GSE2 MB96F346ASB PMC-GSE2 MB96F346AWB PMC-GSE2 MB96F346ASC PQC-GSE2*1 MB96F346AWC PQC-GSE2*1 MB96F346ASC PMC-GSE2 MB96F347ASB PQC-GSE2 MB96F347AWB PQC-GSE2 MB96F347ASB PMC-GSE2 MB96F347AWB PMC-GSE2 MB96F347ASC PQC-GSE2*1 MB96F347AWC PQC-GSE2*1 MB96F347ASC PMC-GSE2 MB96F348ASB PQC-GSE2 MB96F348AWB PQC-GSE2 MB96F348ASB PMC-GSE2 MB96F348AWB PMC-GSE2 MB96F348ASC PQC-GSE2*1 MB96F348AWC PQC-GSE2*1 MB96F348ASC PMC-GSE2 MB96F348CSC PQC-GSE2 MB96F348CWC PQC-GSE2 MB96F348CSC PMC-GSE2 MB96F348CWC PMC-GSE2 Flash A (544KB) Flash B (32KB) *1 *1 *1 *1 *1 *1 Flash/ROM Subclock No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes Package 100 pin Plastic QFP (FPT-100P-M22) 100 pin Plastic LQFP (FPT-100P-M20) Flash A (288KB) 100 pin Plastic QFP (FPT-100P-M22) MB96F346AWC PMC-GSE2 100 pin Plastic QFP (FPT-100P-M22) 100 pin Plastic LQFP (FPT-100P-M20) Flash A (416KB) 100 pin Plastic QFP (FPT-100P-M22) MB96F347AWC PMC-GSE2 100 pin Plastic QFP (FPT-100P-M22) 100 pin Plastic LQFP (FPT-100P-M20) Flash A (544KB) 100 pin Plastic QFP (FPT-100P-M22) MB96F348AWC PMC-GSE2 100 pin Plastic QFP (FPT-100P-M22) 100 pin Plastic LQFP (FPT-100P-M20) *1: These devices are under development and specification is preliminary. These products under development may change its specification without notice. This datasheet is also valid for the following outdated devices: MB96F346YSA, MB96F346RSA, MB96F346YWA, MB96F346RWA, MB96F347YSA, MB96F347RSA, MB96F347YWA, MB96F347RWA, MB96F348YSA, MB96F348RSA, MB96F348YWA, MB96F348RWA, MB96F348TSB, MB96F348HSB, MB96F348TWB, MB96F348HWB, FME-MB96340 rev 10 123 MB96340 Series MB96F346ASA, MB96F346AWA, MB96F347ASA, MB96F347AWA, MB96F348ASA, MB96F348AWA, MB96F348CSB, MB96F348CWB 124 FME-MB96340 rev 10 MB96340 Series ■ REVISION HISTORY Revision Prelim 1 Prelim 2 Prelim 3 Prelim 4 Prelim 5 Date 2007-05-07 2007-05-10 2007-05-23 2007-08-02 2007-09-12 Creation External bus hold timing update Electrical characteristics updates Electrical characteristics updates, Product lineup, changes and ordering information Addition of the electrical characteristic examples and the LVD characteristics specifications, updates of the DC characteristics. Pin circuit type drawing modifications. LVD typo correction. Update of the DC characteristics. Typos corrections. Absolute maximum rating asterisks numbering corrected. Typos page 59: Hardware -> Hardware. IO map table regenerated. Typos corrections. IO circuit drawings modified. Renaming of the Main/Satellite Flash into Flash memory A/B. Memory map reworked. Modification Prelim 6 Prelim 7 2007-11-21 2007-12-04 FME-MB96340 rev 10 125 MB96340 Series Revision Prelim 8 Date 2008-02-04 • • • • • • • • Modification Satellite Flash -> 32kB Data Flash MB96345 added (under development) MB96F348 TSA/HSA/TWA/HWA removed (outdated devices) Block diagram and pin assignment corrected (existing resource pins) Pin function table corrected I/O circuit type diagrams corrected Memory map cleaned up "Flash sector configuration" replaced by corrected "User ROM Memory map for Flash devices", “ROM configuration” replaced by “User ROM Memory map for Mask ROM devices” Parallel Flash programming pinning removed IO map table regenerated: - Port register: Naming style corrected - Memory control registers renamed (Main/Sat -> A/B) - addresses after 000BFFh removed Absolute maximum ratings: Pd and Ta specified more precisely oscillator input levels in oscillation mode with external clock added Run and Sleep mode currents: 96/48MHz and 72/36MHz settings added Run mode current spec in 48/24MHz mode corrected Maximum CLKS1/2 frequency for all devices correctly specified Maximum CLKP2 for MB96F34xY/R/Axx corrected External bus timings: missing conditions added and readability improved Alarm comparator spec updated (transition voltages defined) MB96V300A removed Ordering information updated Typos and formatting corrected • • • • • • • • • • • • • 126 FME-MB96340 rev 10 MB96340 Series Revision 9 Date 2009-01-09 Modification • Format adjusted to official Fujitsu Microelectronics datasheet standard (mainly style changes and official notes and disclaimer added) • Numbering of Electrical Characteristics subchapters automated • Note about devices under development modified • I/O map: Note added about reserved addresses • ICCSPLL for CLKS1=96MHz mode: increased by 1mA • Serial programming interface: Note about handshaking pins improved • specified AD converter channel offset to 4LSB • package code of MB96V300 corrected in ordering information • Added voltage condition to pull-up resistance spec • Lineup: Term “Data Flash” replaced by “independent 32KB Flash” • Ordering information: column “Independent 32KB Data Flash” replaced by new column “Flash/ROM”, column “Remarks” removed • Official package dimension drawing with additional notes added • Empty pages removed • Alarm comparator: Power supply current max values increased, comparison time reduced, mode transition time and power-up stabilization time newly added • Handling devices: Notes added about Serial communication and about using ceramic resonators. • Feature list and AC Characteristics: 16MHz maximum frequency is valid for crystal oscillators. For resonators, maximum frequency depends on Q-factor • AC characteristics: PLL phase skew spec added, CLKVCO min=64MHz • VOL3 spec improved: spec valid for 3mA load for full Vcc range • MB96F345 added • Preliminary DC spec of MB96345/346 added • Permitted power dissipation of Flash devices in QFP package improved • C-Pin cap spec updated: 4.7uF-10uF capacitor with tolerance permitted • “Preliminary” watermark removed FME-MB96340 rev 10 127 MB96340 Series Revision 10 Date 2010-06-23 • • • • • • • • • • • • • • Modification FME-MB96340 rev 10 • • • • • • • I/O map: IOABK0-5 added at address 000A00H-000A05H Ordering Information: Suffix “A” added to all MB96F345 device versions AD converter IAIN spec improved: 1uA valid up to 105deg, 1.2uA above 105deg Corrected MB96F345 part names in ordering information Low voltage detector: Detection levels of MB96F345 updated Example characteristics updated, new figures added showing dependency of PLL Run mode current on frequency Updated Power Supply current spec in Run/Sleep/Timer/Stop modes (new spec items in PLL Run/Sleep mode, small adjustment of most other values) Note added that PLL phase jitter spec does not include jitter coming from Main clock Alarm comparator: Maximum power-up stabilization time increased to 10ms Removed PHDR register from IO map Note added in DC characteristics how to select driving strength of ports I2C AC spec updated: tof, Cb and tSP spec added, wrong footnotes and Condition removed I/O Circuit type: Note added for type “N” (slew rate control according to I2C spec) Package dimension: Added the following sentence under the figure: “Please confirm the latest Package dimension by following URL. http://edevice.fujitsu.com/package/en-search/” AD converter: Impact of input pin capacitance and external capacitance added to formula for calculation of the sampling time Added specification of RC clock stabilization time Feature description I2C: ‘8-bit addressing’ corrected to ‘7-bit addressing’ Feature description PPG: ‘Reload timer overflow as clock input’ corrected to ‘Reload timer underflow as clock input’ Company name updated on the cover page: Fujitsu Microelectronics Limited > Fujitsu Semiconductor Limited ICCLVD specification updated, at 125deg typical value is 7uA and maximum value is 20uA Ordering information: added devices under development MB96F346A*C, MB96F347A*C, MB96F348A*C, MB96F346Y*C, MB96F347Y*C, MB96F348Y*C, MB96F346R*C, MB96F347R*C, MB96F348R*C MB96340 Series FME-MB96340 rev 10 129 MB96340 Series FUJITSU SEMICONDUCTOR LIMITED Nomura Fudosan Shin-yokohama Bldg. 10-23, Shin-yokohama 2-Chome, Kohoku-ku Yokohama Kanagawa 222-0033, Japan Tel: +81-45-415-5858 http://jp.fujitsu.com/fsl/en/ For further information please contact: North and South America FUJITSU MICROELECTRONICS AMERICA, INC. 1250 E. Arques Avenue, M/S 333 Sunnyvale, CA 94085-5401, U.S.A. Tel: +1-408-737-5600 Fax: +1-408-737-5999 http://www.fma.fujitsu.com/ Europe FUJITSU MICROELECTRONICS EUROPE GmbH Pittlerstrasse 47, 63225 Langen, Germany Tel: +49-6103-690-0 Fax: +49-6103-690-122 http://emea.fujitsu.com/microelectronics/ Korea FUJITSU MICROELECTRONICS KOREA LTD. 206 Kosmo Tower Building, 1002 Daechi-Dong, Gangnam-Gu, Seoul 135-280, Republic of Korea Tel: +82-2-3484-7100 Fax: +82-2-3484-7111 http://kr.fujitsu.com/fmk/ Asia Pacific FUJITSU MICROELECTRONICS ASIA PTE. LTD. 151 Lorong Chuan, #05-08 New Tech Park 556741 Singapore Tel : +65-6281-0770 Fax : +65-6281-0220 http://www.fmal.fujitsu.com/ FUJITSU MICROELECTRONICS SHANGHAI CO., LTD. Rm. 3102, Bund Center, No.222 Yan An Road (E), Shanghai 200002, China Tel : +86-21-6146-3688 Fax : +86-21-6335-1605 http://cn.fujitsu.com/fmc/ FUJITSU MICROELECTRONICS PACIFIC ASIA LTD. 10/F., World Commerce Centre, 11 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel : +852-2377-0226 Fax : +852-2376-3269 http://cn.fujitsu.com/fmc/en/ Specifications are subject to change without notice. For further information please contact each office. All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with sales representatives before ordering. The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of FUJITSU SEMICONDUCTOR device; FUJITSU SEMICONDUCTOR does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. FUJITSU SEMICONDUCTOR assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU SEMICONDUCTOR or any third party or does FUJITSU SEMICONDUCTOR warrant non-infringement of any third-party's intellectual property right or other right by using such information. FUJITSU SEMICONDUCTOR assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that FUJITSU SEMICONDUCTOR will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of overcurrent levels and other abnormal operating conditions. Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws. The company names and brand names herein are the trademarks or registered trademarks of their respective owners. Edited: Sales Promotion Department 130 FME-MB96340 rev 10