NA-5W-K

FTR-K1 SERIES MINIATURE RELAY 2 POLES - 1 to 2 A (For Signal Switching) NA Series n FEATURES Slim type relay for high density mounting Conforms to Telcordia specification and FCC Part 68 - Dielectric strength 1,500 VAC between coil and contacts - Surge strength 2,500 V between coil and contacts (at 2 × 10 s surge wave) l UL, CSA recognized l High sensitivity and low consumption power l High reliability - bifurcated contacts l DIL pitch terminals l Plastic sealed type l RoHS compliant. Please see page 8 for more information l l n PARTNUMBER INFORMATION [Example] (a) NA (a) L D 12 W - K (b) (*) (c) (d) (e) (f) Relay type NA : NA-Series (b) Coil type A B : Standard type : Latching type (1 coil) (c) Number of coil Nil D : Single winding type : Double winding type (d) Coil rated voltage 12 : 1.5.....48 VDC Coil rating table at page 3 (e) Contact W : Bifurcated type (f) Enclosure K : Plastic sealed type Note: Actual marking omits the hyphen ( - ) of (*). 1 FTR-K1NA SERIES SERIES n SPECIFICATION Item Contact Data Life Coil Data Standard type Single winding latching type Double winding latching type NA - ( ) W - K NAL - ( ) W - K NAL-D ( ) W - K Configuration 2 form C (DPDT) Construction Bifurcated Material Gold overlay silver alloy (AgPd) Resistance (Initial) Max. 50 mΩ at 1 A, 6 VDC Contact rating (resistive) 0.5A, 125VAC or 1A, 30VDC Max. carrying current 2A Max. switching voltage 250VAC / 220VDC Max. switching power 62.5 AV / 30W Max. switching current 2A Min. switching load * 0.01 mA, 10 mVDC Capacitance (at 1kHz, reference) Approx. 0.5 pF (open contacts, adjacent contacts) Approx. 1.0 pF (between coil and contacts) Mechanical Min. 100 x 106 operations Electrical Min. 200 x 103 operations (0.5A, 125VAC), Min. 500 x 103 operations (1A, 30VDC) Rated power 140 - 300 mW Min. 10 x 106 operations 100 - 150 mW Applied pulse width Timing Data Insulation min. 10ms Operate power 80 - 70 mW Operating temperature range -40 °C to +85 °C (no frost) 60 - 85 mW Operate (at nominal voltage, without bounce) Max. 6 ms Max. 6 ms (set) Release (at nominal voltage, without bounce) Max. 4 ms Max. 6 ms (reset) Resistance (Initial) Min. 1,000MΩ at 500VDC Dielectric strength Surge strength Other 200 - 300 mW Vibration resistance Shock Weight 115 - 170 mW Open contacts / adjacent contacts 1,000VAC (50/60Hz) 1min Contacts to coil 1,500VAC (50/60Hz) 1min. Open contacts / adjacent contacts 1,500V / 10 x 700µs standard wave Coil to contacts 2,500V / 2 x 10µs standard wave Misoperation 10 to 55 to 10Hz single amplitude 1.65mm Endurance 10 to 55 to 10Hz single amplitude 2.5mm Misoperation 500m/s² (11 ± 1ms) Endurance 1,000m/s² (6 ± 1ms) 1,000VAC (50/60Hz) 1min 1,500V / 10 x 160µs standard wave Approximately 1.6 g * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2 FTR-K1NA SERIES SERIES n COIL RATING Standard type Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must Release Voltage (VDC) * Max. Coil Voltage (VDC) 1.5 1.5 16.1 +1.13 +0.15 3.6 3 3 64.3 +2.25 +0.3 7.2 4.5 4.5 145 +3.38 +0.45 10.8 5 5 178 +3.75 +0.5 12.0 6 6 257 +4.5 +0.6 14.4 9 9 579 +6.75 +0.9 21.6 12 12 1,028 +9 +1.2 28.8 18 18 1,620 +13.5 +1.8 36.0 24 24 2,880 +18 +2.4 48.0 48 48 7,680 +36 +4.8 84.0 Rated Power (mW) 140 200 300 Single winding latching type Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Set Voltage (VDC) * Reset Voltage (VDC) * 1.5 1.5 22.5 +1.13 -1.13 3 3 90 +2.25 -2.25 4.5 4.5 203 +3.38 -3.38 5 5 250 +3.75 -3.75 6 6 360 +4.5 -4.5 9 9 810 +6.75 -6.75 12 12 1,440 +9 -9 18 18 2,160 +13.5 -13.5 24 24 3,840 +18 -18 Rated Power (mW) 100 150 Note: All values in the tables are valid for 20°C and zero contact current. * Specified operate values are valid for pulse wave voltage. Please use at rated coil voltage. Please refer to characteristic data and set up adequate voltage in case of use at over voltage. 3 FTR-K1NA SERIES SERIES n COIL RATING Double winding latching type Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Set Voltage (VDC) * 1.5 1.5 P 11.25 +1.13 S 11.25 3 3 P 45 4.5 P 101 +2.25 +2.25 +3.38 S 101 5 5 P 125 +3.38 +3.75 S 125 6 6 P 180 9 P 405 +4.5 +4.5 +6.75 S 405 12 12 P 720 +6.75 +9 S 720 18 18 P 1,080 +9 +13.5 S 1,080 24 24 P 1,920 200 +3.75 S 180 9 Rated Power (mW) +1.13 S 45 4.5 Reset Voltage (VDC) * +13.5 300 +18 S 1,920 +18 Note: All values in the table are measured at 20°C and zero contact current. P: Primary coil S: Secondary coil * Specified values are measured with pulse wave voltage Please use at rated coil voltage. Please refer to characteristic data and set up adequate voltage in case of use at over voltage. n SAFETY STANDARDS Type Compliance Contact rating UL UL 508, UL 1950 Flammability: UL 94-V0 (plastics) E 45026 0.5A, 125VAC (general use) 2A, 30VDC (resistive) 0.3A, 110VDC (resistive) CSA C22.2 No. 14, No. 950 LR 35579 Complies to IEC60950-1; FCC part 68: Telcordia (Relay is only marked with UL and CSA logo) 4 FTR-K1NA SERIES SERIES n CHARACTERISTIC DATA 5 FTR-K1 SERIES NA SERIES 6 FTR-K1NA SERIES SERIES n DIMENSIONS l PC board mounting hole layout (BOTTOM VIEW) l Schematics (BOTTOM VIEW) l Dimensions NA (standard type) NAL (single winding latching type) 14.9+0.3 7.4+0.3 1 3 4 5 12 10 Orientation mark 9 8 5.08 7.4 9.7+0.3 8- φ0.8 14.9 +(-) 5.08 2.54 2.54 3.0 (1.1) (1.16) -(+) (1.1) 0.5 5.08 0.2 2.54 2.54 2.54 (1.16) 5.08 l PC board mounting hole layout (BOTTOM VIEW) l Schematics (BOTTOM VIEW) l Dimensions NAL-D (double winding latching type) 3 4 5 +(-) 9.7+0.3 P -(+) 3.0 12 10 Orientation mark (1.1) 0.5 5.08 0.2 2.54 2.54 2.54 S (1.16) 5.08 10- φ0.8 14.9 (+) 5.08 1 (-) 9 8 (1.1) 5.08 2.54 2.54 2.54 (1.16) 7.4+0.3 7.4 14.9+0.3 * Contact drawn in reset condition. * +/-: set voltage applied polarity, (+)/(-): reset voltage applied polarity. * P: Set coil, S: Reset coil. Unit: mm * Dimensions of the terminals do not include thickness of pre-solder. * Tolerance of PC board mounting hole layout : ±0.1 unless otherwise specified. 7 FTR-K1NA SERIES SERIES RoHS Compliance and Lead Free Information 1. General Information All relays produced by Fujitsu Components are compliant with RoHS directive 2011/65/EU including amendments. l Cadmium as used in electrical contacts is exempted from the RoHS directives. As per Annex III of directive 2011/65/EU. l All relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/downloads/MICRO/fcai/relays/lead-free-letter.pdf l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. l 2. Recommended Lead Free Solder Condition l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder Condition: Pre-heating: maximum 120˚C within 90 sec. Soldering: dip within 5 sec. at 255˚C ± 5˚C solder bath Relay must be cooled by air immediately after soldering Solder by Soldering Iron: Soldering Iron 30-60W Temperature: maximum 350-360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 8 FTR-K1NA SERIES SERIES Fujitsu Components International Headquarter Offices Japan FUJITSU COMPONENT LIMITED Shinagawa Seaside Park Tower 19F, 12-4, Higashi-shinagawa 4-chome, Shinagawa-ku, Tokyo,140-0002, Japan Tel: (81-3) 3450-1682 Fax: (81-3) 3474-2385 Email: fcl-contact@cs.jp.fujitsu.com Web: www.fujitsu.com/jp/fcl/ Asia Pacific FUJITSU COMPONENTS ASIA, LTD. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components North and South America FUJITSU COMPONENTS AMERICA, INC 2290 North First Street, Suite 212 San Jose, CA 95131, USA Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: us.fujitsu.com/components China FUJITSU ELECTRONIC COMPONENTS (SHANGHAI) CO., LTD. Unit 4306, InterContinental Center 100 Yu Tong Road, Shanghai 200070, China Tel: (86-21) 3253 0998 Fax: (86-21) 3253 0997 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components Europe FUJITSU COMPONENTS EUROPE B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: www.fujitsu.com/uk/components Hong Kong FUJITSU COMPONENTS HONG KONG CO., LTD Unit 506, Inter-Continental Plaza No.94 Granville Road, Tsim Sha Tsui, Kowloon, Hong Kong Tel: (852) 2881-8495 Tex: (852) 2894-9512 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components/ Korea FUJITSU COMPONENTS KOREA LIMITED Alpha Tower #403, 645 Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, 13524 Korea Tel: (82) 31-708-7108 Fax: (82) 31-709-7108 Email: fcal@sg.fujitsu.com www.fujitsu.com/sg/products/devices/components/ ©2018 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. August 29, 2018 9