NAL-12W-K

MINIATURE RELAY 2 POLES—1 to 2 A (FOR SIGNAL SWITCHING) NA SERIES n FEATURES l RoHS compliant Slim type relay for high density mounting l Conforms to Bellcore specification and FCC Part 68 —Dielectric strength 1,500 VAC between coil and contacts —Surge strength 2,500 V between coil and contacts (at 2 × 10 s surge wave) l Maximum switching capability - 4.2A, 700VAC l UL, CSA recognized l High sensitivity and low consumption power l High reliability—bifurcated contacts l DIL pitch terminals l Plastic sealed type l RoHS compliant since date code: 0437B8 Please see page 7 for more information [Example] (a) (b) (c) (d) (e) (f ) n ORDERING INFORMATION NA L – D 12 W – K (a) (b) (*) (c) (d) (e) (f ) Series Name Operation Function Number of Coil Nominal Voltage Contact Enclosure NA : NA Series Nil : Standard type L : Latching type Nil : Single winding type D : Double winding type Refer to the COIL DATA CHART W : Bifurcated type K : Plastic sealed type Note: ctual marking omits the hyphen (-) of (*) A 1 NA SERIES n COIL DATA CHART MODEL NA-1.5 W-K NA- 3 W-K NA-4.5 W-K NA- 5 W-K NA- 6 W-K NA- 9 W-K NA-12 W-K NA-18 W-K NA-24 W-K NA-48 W-K Nominal voltage 1.5 VDC 3 VDC 4.5 VDC 5 VDC 6 VDC 9 VDC 12 VDC 18 VDC 24 VDC 48 VDC Coil resistance (±10%) 16.1 Ω 64.3 Ω 145 Ω 178 Ω 257 Ω 579 Ω 1,028 Ω 1,620 Ω 2,880 Ω 7,680 Ω Must operate voltage*1 +1.13 VDC +2.25 VDC +3.38 VDC +3.75 VDC +4.5 VDC +6.75 VDC +9.0 VDC +13.5 VDC +18.0 VDC +36.0 VDC Must release voltage* +0.15 VDC +0.3 VDC +0.45 VDC +0.5 VDC +0.6 VDC +0.9 VDC +1.2 VDC +1.8 VDC +2.4 VDC +4.8 VDC Nominal power 140 mW 140 mW 140 mW 140 mW 140 mW 140 mW 140 mW 200 mW 200 mW 300 mW Note: *1 Specified values are subject to pulse wave voltage. All values in the table are measured at 20°C. MODEL NAL-1.5W-K Single Winding Latching Type NAL- 3 W-K NAL-4.5W-K NAL- 5 W-K NAL- 6 W-K NAL- 9 W-K NAL-12 W-K NAL-18 W-K NAL-24 W-K Double Winding Latching Type NAL-D1.5W-K NAL-D 3 W-K NAL-D4.5W-K NAL-D 5 W-K NAL-D 6 W-K NAL-D 9 W-K NAL-D12 W-K NAL-D18 W-K NAL-D24 W-K Nominal voltage 1.5 VDC 3 VDC 4.5 VDC 5 VDC 6 VDC 9 VDC 12 VDC 18 VDC 24 VDC 1.5 VDC 3 VDC 4.5 VDC 5 VDC 6 VDC 9 VDC 12 VDC 18 VDC 24 VDC Coil resistance (±10%) 22.5 Ω 90 Ω 203 Ω 250 Ω 360 Ω 810 Ω 1,440 Ω 2,160 Ω 3,840 Ω P 11.25 Ω S 11.25 Ω P S P S P S P S P S P S 45 Ω 45 Ω 101 Ω 101 Ω 125 Ω 125 Ω 180 Ω 180 Ω 405 Ω 405 Ω 720 Ω 720 Ω Set voltage +1.13 VDC +2.25 VDC +3.38 VDC +3.75 VDC +4.5 VDC +6.75 VDC +9.0 VDC +13.5 VDC +18.0 VDC +1.13 VDC +2.25 VDC +3.38 VDC +3.75 VDC +4.5 VDC +6.75 VDC +9.0 VDC +13.5 VDC +18.0 VDC Reset voltage –1.13 VDC –2.25 VDC –3.38 VDC –3.75 VDC –4.5 VDC –6.75 VDC –9.0 VDC –13.5 VDC –18.0 VDC +1.13 VDC +2.25 VDC +3.38 VDC +3.75 VDC +4.5 VDC +6.75 VDC +9.0 VDC +13.5 VDC +18.0 VDC Nominal power 100 mW 100 mW 100 mW 100 mW 100 mW 100 mW 100 mW 150 mW 150 mW 200 mW 200 mW 200 mW 200 mW 200 mW 200 mW 200 mW 300 mW 300 mW Standard Type P 1,080 Ω S 1,080 Ω P 1,920 Ω S 1,920 Ω Note: *1 Specified values are subject to pulse wave voltage. All values in the table are measured at 20°C. P: Primary coil S: Secondary coil 2 NA SERIES n SPECIFICATIONS Item Contact Arrangement Material Style Resistance (initial) Rating (resistive) Maximum Carrying Current Maximum Switching Power Maximum Switching Voltage Maximum Switching Current Minimum Switching Load* Capacitance Coil Nominal Power (at 20°C) Operate Power (at 20°C) Operating Temperature Time Value Life Other *1 Operate (at nominal voltage) Release (at nominal voltage) Mechanical Electrical Vibration Misoperation Resistance Endurance Shock Misoperation Resistance Endurance Weight 1 Standard Type NA-( ) W-K 2 form C (DPDT) Single Winding Latching Type NAL-( ) W-K Double Winding Latching Type NAL-D ( ) W-K Gold overlay silver alloy Bifurcated Maximum 50 mΩ (at 1 A 6 VDC) 0.5 A 125 VAC or 1 A 30 VDC 2 A 62.5 AV, 30 W 250 VAC, 220 VDC 2 A 0.01 mA 10 mVDC Approximately 0.5 pF (between open contacts, adjacent contacts) Approximately 1.0 pF (between coil and contacts) 140 to 300 mW 80 to 170 mW Maximum 6 ms Maximum 4 ms 1 × 10 100 to 150 mW 60 to 85 mW Maximum 6 ms (set) Maximum 6 ms (reset) 200 to 300 mW 115 to 170 mW –40°C to +85°C (no frost)(refer to the CHARACTERISTIC DATA) 8 operations minimum 1 × 107 operations minimum 2 × 105 ops. min. (0.5 A 125 VAC), 5 × 105 ops. min. (1 A 30 VDC) 10 to 55 Hz (double amplitude of 3.3 mm) 10 to 55 Hz (double amplitude of 5.0 mm) 500 m/s2 (11 ±1 ms) 1,000 m/s2 ( 6 ±1 ms) Approximately 1.5 g Minimum switching loads mentioned above are reference values. Please perform the confirmation test with the actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 3 NA SERIES n INSULATION Item Resistance (initial) (500 VDC) Dielectric Strength Surge Voltage Standard Single latching Double latching Minimum 1,000 MΩ 1,000 VAC 1 min. (open contacts / adjacent contents) 1,500 VAC 1 min. (coil and contacts) 2,500V (coil and contact) 2 x 10µs standard wave 1,000 VAC 1 min. (coil and contacts) 1,500V (coil and contact) 10 x 160µs standard wave 1,500V (open contact and adjacent contact) 10 x 700µs standard wave n SAFETY STANDARDS Type UL Compliance UL 508, UL 1950 E45026 CSA C22.2 No. 14, No. 950 LR 35579 Contact rating Flammability: UL 94-V0 (plastics) 0.5A, 125VAC (general use) 2A, 30VDC (resistive) 0.3A, 110VDC (resistive) 4 NA SERIES n CHARACTERISTIC DATA 150 High Frequency Characteristics (Isolation) 1.8 High Frequency Characteristics (Insertion Loss) NA-12W-K n=2 Transmission impedance 75 Note: In standard PC board for measurement betweem common and make contacts Insertion Loss (dB) Isolation (dB) 100 NA-12W-K n=2 Transmission impedance 75 Note: In standard PC board for measurement betweem common and make contacts 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 50 0 1 3 5 7 10 Frequency (MHz) 30 50 70 100 300 500 700 1000 0 1 3 5 7 10 Frequency (MHz) 30 50 70 100 300 500 700 1000 5 NA SERIES n REFERENCE DATA 6 NA SERIES n DIMENSIONS l Dimensions l Schematics (Bottom View) l PC board mounting hole layout (Bottom View) NA, NAL type (Non-latching type, single winding latching type) NAL-D type (double winding latching type) Unit: mm 7 NA SERIES RoHS Compliance and Lead Free Relay Information 1. General Information Relays produced after the specific date code that is indicated on each data sheet are lead-free now. All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info. (http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf) l Lead free solder paste currently used in relays is Sn-3.0Ag-0.5Cu. l All signal and power relays also comply with RoHS. Please refer to individual data sheets. Relays that are RoHS compliant do not contain the 5 hazardous materials that are restricted by RoHS directive (lead, mercury, chromium IV, PBB, PBDE). l It has been verified that using lead-free relays in leaded assembly process will not cause any problems (compatible). l “LF” is marked on each outer and inner carton. (No marking on individual relays). l To avoid leaded relays (for lead-free sample, etc.) please consult with area sales office. l We will ship leaded relays as long as the leaded relay inventory exists. Note: Cadmium was exempted from RoHSon October 21, 2005. (Amendment to Directive 2002/95/EC) l 2. Recommended Lead Free Solder Profile l Recommended solder paste Sn-3.0Ag-0.5Cu. Reflow Solder condition Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C soler bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical realys. Dipped SnAgCu solder is known as low risk tin whisker. No considerable length whisker was found by our in house test. 4. Tin Whisker l 8 NA SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://www.fujitsu.com/us/services/edevices/components/ Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ ©2008 Fujitsu Components America, Inc. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. Fujitsu Components America or its affiliates do not warrant that the content of datasheet is error free. In a continuing effort to improve our products Fujitsu Components America, Inc. or its affiliates reserve the right to change specifications/datasheets without prior notice. Rev. January 8, 2008. 9