VSB-12MC

POWER RELAY 1 POLE—16 A (HEAVY POWER CONTROL) VSB SERIES n FEATURES l l RoHS compliant l l l l l l l l All or nothing relay UL, CSA, VDE, SEV, FIMKO, SEMKO, ÖVE, BSI recognized Working class: C Type of service: continuous duty Heavy duty 16 A miniature power relay UL Class B (130°C) insulation High isolation in small package —Insulation distance: 8 mm —Dielectric strength: 5,000 VAC (between coil and contacts) —Surge strength: 10,000 V Low power consumption and high sensitivity type available VSB-S) Plastic sealed (with tape) type available RoHS compliant since date code:0523 Please see page 6 for more information To be S (c) Di B (e) sc n ORDERING INFORMATION [Example] (a) (b) (c) (d) (e) VSB – 12 (a) (*) (b) T (d) on Ti Series Name Nominal Voltage Coil Type Contact Arrangement Enclosure VSB : VSB Series Refer to the COIL DATA CHART Nil : Standard type (700 to 750 mW) S : High sensitivity type (530 mW) M T B C : 1 form A (SPST-NO) : 1 form C (SPDT) : Flux free type : Plastic sealed type (with tape) nu eD 1 Note: Actual marking omits the hyphen (-) of (*) VSB SERIES n COIL DATA CHART MODEL VSBVSBVSBVSBStandard Type 3( )( ) 5( )( ) 6( )( ) 9( )( ) Nominal voltage 3 VDC 5 VDC 6 VDC 9 VDC 12 VDC 14 VDC 18 VDC 24 VDC 36 VDC 60 VDC Coil resistance (±10%) 12.5 Ω 36 50 115 200 280 460 820 1,850 3,300 5,100 13,400 Ω Ω Ω Ω Ω Ω Ω Ω Ω Ω Ω Must operate voltage* 2.1 VDC 3.5 VDC 4.2 VDC 6.3 VDC 8.4 VDC 9.8 VDC 12.6 VDC 16.8 VDC 25.2 VDC 33.6 VDC 42.0 VDC 70.0 VDC 2.1 VDC 3.5 VDC 4.2 VDC Must release voltage* 0.3 VDC 0.5 VDC 0.6 VDC 0.9 VDC 1.2 VDC 1.4 VDC 1.8 VDC 2.4 VDC 3.6 VDC 4.8 VDC 6.0 VDC 10.0 VDC 0.3 VDC 0.5 VDC 0.6 VDC 0.9 VDC 1.2 VDC 1.4 VDC 1.8 VDC Nominal power 720 mW 700 mW 720 mW 700 mW 720 mW 700 mW 700 mW 700 mW 700 mW 700 mW 700 mW 750 mW 530 mW 530 mW 530 mW 530 mW 530 mW 530 mW 530 mW 530 mW 530 mW To VSBVSBVSBVSB- VSB- 12 ( ) ( ) VSB- 14 ( ) ( ) VSB- 18 ( ) ( ) VSB- 24 ( ) ( ) VSB- 36 ( ) ( ) VSB- 60 ( ) ( ) VSB- 48 ( ) ( ) VSB-100 ( ) ( ) 3S ( ) ( ) be 48 VDC 100 VDC 3 VDC 5S ( ) ( ) 6S ( ) ( ) 9S ( ) ( ) 5 VDC 9 VDC 12 VDC 14 VDC 18 VDC 24 VDC 36 VDC 48 VDC 60 VDC 100 VDC 6 VDC High Sensitivity Type Di VSB- 12S ( ) ( ) VSB- 14S ( ) ( ) VSB- 18S ( ) ( ) VSB- 24S ( ) ( ) VSB- 36S ( ) ( ) VSB- 48S ( ) ( ) VSB- 60S ( ) ( ) VSB-100S ( ) ( ) sc 17 Ω 47 Ω 68 Ω 155 Ω 270 Ω 610 Ω 1,100 Ω 2,450 Ω 4,400 Ω 6,800 Ω 18,560 Ω 370 Ω on 6.3 VDC 8.4 VDC 9.8 VDC 12.6 VDC 16.8 VDC 33.6 VDC 25.2 VDC 42.0 VDC Ti 70.0 VDC nu 2.4 VDC 4.8 VDC 3.6 VDC 6.0 VDC 10.0 VDC Note: All values in the table are measured at 20°C. *: Specified values are subject to pulse wave voltage eD 530 mW 530 mW 530 mW  VSB SERIES n SPECIFICATIONS Item Contact Arrangement Material Configuration Resistance (initial) Rating Maximum Carrying Current*1 Maximum Switching Rating Maximum Switching Voltage Maximum Switching Current Maximum Switching Load*2 Nominal Power (at 20ºC) Operate Power (at 20ºC) Operating Temperature Time Value Life Other Standard Type VSB- ( ) Silver alloy (AgSnO) Single Maximum 100 mΩ at 1 A, 6 VDC 16 A, 250 VAC / 30 VDC 16 A 4,000 VA / 480W 250 VAC / 150VDC 16A 100 mA 5 VDC 700 to 750 mW 350 to 370 mW -40ºC to +65ºC (no frost) 530 mW 260 mW -40ºC to +75ºC (no frost) High Sensitive type VSB-( )-S 1 form A (SPST- NO) or 1 form C (SPDT) Coil To Operate (at nominal voltage) Mechanical Electrical Vibration Resistance Shock Resistance Weight be Release (at nominal voltage) Di Misoperation Endurance Misoperation Endurance sc Maximum 15ms Maximum 10ms 2 x 107 operations minimum 1 x 105 operations minimum (contact rating) 10 to 55 Hz, at double amplitude of 1.5 mm 10 to 55Hz, at double amplitude of 1.5 mm Min. 100m/s2 (11±1ms) Approximately 18g Min. 1,000m/s2 (6±1ms) on *1 Need to consider the head from PCB when max. current is more than 10A. *2 Minimum switching loads mentioned above are reference values. Please perform the confirmation test with the actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. Ti n INSULATION Item Resistance (initial) Dielectric Strength open contacts coil and contacts VSB Minimum 1,000 MΩ nu Note at 500 VDC eD 1,000 VAC (50/60 Hz) 1 min. 5,000 VAC (50/60 Hz) 1 min. 10,000 V Contact rating Flammability: UL 94-V0 (plastics) 16A, 250VAC/30VDC (resistive) 1/3 HP, 250VAC/125VAC Pilot duty: C150 1.2 x 50µs standard wave Surge Voltage (coil and contact) n SAFETY STANDARDS Type UL Compliance UL 508, 873 E56140 CSA VDE C22.2 No. 14 LR 35579 0435, 0631, 0700, 0860  Complies with SEV, SEMKO, FIMKO, ÖVE, BSI VSB SERIES n CHARACTERISTIC DATA To be Di n REFERENCE DATA sc on Ti nu eD  VSB SERIES n DIMENSIONS l Dimensions l PC board mounting hole layout (BOTTOM VIEW) l Schematics (BOTTOM VIEW) VSB-M type VSB type To be Di sc VSB-MC type (Plastic sealed type with tape) on Ti nu eD VSB-C type (Plastic sealed type with tape) Unit: mm  VSB SERIES 1. General Information l RoHS Compliance and Lead Free Relay Information Relays produced after the specific date code that is indicated on each data sheet are lead-free now. All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info. (http://www.fcai.fujitsu.com/pdf/LeadFreeLetter.pdf) l Lead free solder paste currently used in relays is Sn-3.0Ag-0.5Cu. From February 2005 forward Sn-3.0Cu-Ni will be used for FTRB3 and FTR-B4 series relays. l All signal and power relays also comply with RoHS. Please refer to individual data sheets. Relays that are RoHS compliant do not contain the 6 hazardous materials that are restricted by RoHS directive (lead, mercury, cadmium, chromium IV, PBB, PBDE). l It has been verified that using lead-free relays in leaded assembly process will not cause any problems (compatible). l “LF” is marked on each outer and inner carton. (No marking on individual relays). l To avoid leaded relays (for lead-free sample, etc.) please consult with area sales office. We will ship leaded relays as long as the leaded relay inventory exists. . Recommended Lead Free Solder Profile l To Recommended solder paste Sn-3.0Ag-0.5Cu and Sn-3.0 Cu-Ni (only FTR-B3 and FTR-B4 from February 2005) Reflow Solder condition Flow Solder condition: Pre-heating: Soldering: be maximum 120˚C dip within 5 sec. at 260˚C soler bath Di sc Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. on Ti We highly recommend that you confirm your actual solder conditions nu . Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical realys. eD . Tin Whisker l SnAgCu solder is known as low riskof tin whisker. No considerable length whisker was found by our in-house test. Each lead terminal will be changed from solder plating to Sn plating and Nickel plating. A layer of Nickel plating is between the terminal and the Sn plating to avoid whisker. . Solid State Relays l 6 VSB SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ To North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://www.fujitsu.com/us/services/edevices/components/ ©2009 Fujitsu Components America, Inc. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. Fujitsu Components America or its affiliates do not warrant that the content of datasheet is error free. In a continuing effort to improve our products Fujitsu Components America, Inc. or its affiliates reserve the right to change specifications/datasheets without prior notice. Rev. June 30, 2009 be Di sc on Ti nu eD