B501BH

SS-I Features • Sleek, low-profile design. • Addressable-analog communication. • Stable communication technique with noise immunity. • Low standby current. • Two-wire SLC connection. • Rotary, decimal addressing (1 – 99). • Optional remote, single-gang LED accessory (RA400Z). • Dual LED design provides 360° viewing angle. • Visible bicolor LEDs blink green every time the detector is addressed, and illuminate steady red on alarm. • Remote test feature from the panel. • Built-in functional test switch activated by external magnet. • Built-in tamper-resistant feature. • Sealed against back pressure. • Constructed of off-white Bayblend®, designed to commercial standards, and offers an attractive appearance. • 94-5V plastic flammability rating. • SEMS screws for wiring of the separate base. • Optional relay, isolator, or sounder bases. • Backward-compatible. Intelligent Addressable Plug-In Ionization Smoke Detector Description Gamewell’s intelligent TM SmartScan plug-in smoke detector with integral communication provides features that surpass conventional detectors. Detector sensitivity can be programmed in the control panel software. Sensitivity is continuously moni6934pho1.jpg tored and reported to the panel. Point ID capability alSS-I with SS-B6 base lows each detector’s address to be set with decade address switches, providing exact detector locations for selective maintenance when chamber contamination reaches an unacceptable level. The SS-I ionization detector incorporates a unique singlesource, dual-chamber design to respond quickly and dependably to a broad range of fires. The SS-I detector is compatible with Gamewell’s 602, 610, 632, 654 and 658 FACPS with a SmartScanTM SLC. Installation The SS-I plug-in detector uses a separate base to simplify installation, service, and maintenance. A special tool allows maintenance personnel to plug in and remove detectors without using a ladder. Mount base on an electrical backbox which is at least 1.5" (3.81 cm) deep. Suitable mounting back boxes include: • 4.0" (10.16 cm) square box. • 3.5" (8.89 cm) or 4.0" (10.16 cm) octagonal box. • Single-gang box (except for relay or isolator base). • With B501BH or B501BHT base, use a 4.0" (10.16 cm) square box. • With B224RB or B224BI base, use a 3.5" (8.89 cm) octagonal box, or a 4.0" (10.16 cm) octagonal or square box. NOTES: 1) Because of the inherent supervision provided by the SLC loop, end-ofline resistors are not required. Wiring “T-taps” or branches are permitted for Style 4 (Class “B”) wiring. 2) When using relay or sounder bases, consult data sheet CS2464 (SS-LI) for device limitations between isolator modules and isolator bases. Listings Listings and approvals below apply to the SS-I Intelligent Plug-In Ionization Smoke Detector. In some cases, the detector may not be listed by certain approval agencies, or listing may be in process. Consult factory for latest listing status. • UL Listed: file S1195. • CSFM approved: file 7271-1288:168. Bayblend® is a registered trademark of Bayer Corporation. SS-I CS-2459 09/01/06 Page 1 of 2 Product Line Information SS-I: Low-profile intelligent ionization M02-09-00: Test magnet with telescope smoke detector. Must be mounted to one stick. of the bases listed below. XR2B: Detector removal tool. Allows Bases: installation and/or removal of SS-I detector heads from base in high ceiling SS-B6: Standard U.S. low-profile base, installations. UL Listing. B501BP: Standard European flangeless T55-127-000: Detector removal tool without pole. base, pkg. of 10. XP-4: Extension pole for XR2B. Comes B501BH: Sounder base, includes B501 in three 5-ft. sections. base above. Specifications Wiring Diagrams Size 2.1" (5.3 cm) high x 4.1" (10.4 cm) diameter installed in B501 base, 6.1" (15.5 cm) diameter installed in SS-B6 base. Shipping weight 5.4 oz. (154 g). Operating temperature 0°C to 49°C (32°F to 120°F). UL-Listed velocity range: B501BHT: Same as B501BH, but Detector Guards: ION: 0 – 1200 ft./min. (365.76 m/min.). includes temporal sounder. NOTE: The following guards are not UL Relative humidity B224RB: Intelligent relay base. listed with the SS-I detectors. Consult AHJ. 10% – 93% noncondensing. STI 9601: Low-profile, flush-mount smoke Accessories: DETECTOR SPACING: detector guard, wire. RA400Z: Remote LED annunciator. 3 – Gamewell recommends spacing detec32 VDC. Fits U.S. single-gang electrical STI 9602: Low-profile, surface-mount, tors in compliance with NFPA 72. In low smoke detector guard, wire. box. Supported by SS-B6 and B501 airflow applications with smooth ceilings, STI 9609: High-profile, flush-mount, smoke space detectors 30 feet (9.144 m). For bases only. SMK400: Surface mounting kit provides detector guard, wire. specific information regarding detector STI 9605: High-profile, surface-mount, for entry of surface wiring conduit. For spacing, placement, and special applicasmoke detector guard, wire. use with B501 base only. tions, refer to NFPA 72. System Smoke STI 9604: Flush-mount heat detector RMK400: Recessed mounting kit. For Detector Application Guide, document guard, wire. use with B501 base only. A05-1003, is available at systemsensor.com. SMB600: Surface mounting kit for use STI 9610: Surface-mount heat detector with SS-B6. guard, wire. ELECTRICAL SPECIFICATIONS: BCK-200B: Black detector covers, box of STI-8200-SS: Flush-mount stainless Voltage range 10. Use with SS-I. steel smoke detector guard 15 - 32 volts DC peak. M02-04-01: Test magnet. STI-8230-SS: Surface-mount stainless Standby current (max. avg.) steel smoke detector guard 200 µA @ 24 VDC (without communication); 300 µA @ 24 VDC (one communication every 5 seconds with LED enabled). LED current (max.) 6.5 mA @ 24 VDC (“ON”). BASES AVAILABLE: SS-B6: 6.1" (15.5 cm) diameter. B501: 4.1" (10.4 cm) diameter. B501BH or B501BHT: Sounder base assembly. Includes B501 base. B224RB Relay Base: Screw terminals: up to 14 AWG (2.0 mm²). Relay type: Form-C. Rating: 2.0 A @ 30 VDC resistive; 0.3 A @ 110 VDC inductive; 1.0 A @ 30 VDC inductive. Dimensions: 6.2" (15.748 cm) x 1.2" (3.048 cm). B224BI Isolator Base: Dimensions: 6.2" (15.748 cm) x 1.2" (3.048 cm). Maximum: 25 devices between isolator bases. Gamewell-FCI 12 Clintonville Road Northford, CT 06472-1610 Phone: 203-484-7161 Fax: 203-484-7118 www.gamewell-fci.com A Honeywell Company © 2006 Gamewell-FCI Address dial on back of detector. Specifications and wiring information are provided for information only and are believed to be accurate. Gamewell-FCI assumes no responsibility for their use. Data and design are subject to change without notice. Installation and wiring instructions shipped with the product shall always be used for actual installation. For more information, contact Gamewell-FCI. Page 2 of 2 SS-I CS-2459 09/01/06