BB-25

厂商：
GAMEWELL-FCI
封装：
描述：
BB-25 - Ten-Input Monitor Module - Gamewell-FCI by Honeywell

数据手册：

下载BB-25.pdf

立即购买

详情介绍
数据手册
价格&库存

BB-25 数据手册

PIM-SS Features • Ten addressable Class B or five addressable Class A initiating device circuits. • Removable 12 AWG (3.25 mm²) to 18 AWG (0.9 mm²) plug-in terminal blocks. • Use with Gamewell’s IF602, 610, 632, 654 and 658 with SmartScan™ loop card. • Status indicators for each point. • Unused addresses may be disabled. • Rotary address switches. • Class A or Class B operation. • Mount one or two modules in a BB-XP cabinet (optional). • Mount up to six modules on a CHS-6 chassis in a BB-25 cabinet (optional). • Mounting hardware included. Ten-Input Monitor Module Description Gamewell’s SmartScanTM PIM-SS teninput monitor module provides an interface between a control panel and normally open contact devices in intelligent alarm systems such as conventional pull stations and heat detectors. The first address on the PIM-SS is set from 01 to 90 and the remaining modules are automatically assigned to the next nine higher addresses. Provisions are included for disabling a maximum of two unused addresses. SS-M with SS-B6 base The supervised state (normal, open, or short) of the monitored device is sent back to the panel. A common SLC input is used for all modules, and the initiating device loops share a common supervisory supply and ground — otherwise each monitor operates independently from the others. Each PIM-SS module has panel-controlled green LED indicators. The panel can cause the LEDs to blink, latch on, or latch off. Listings Listings and approvals below apply to the PIM-SS Ten-Input Monitor Module. In some cases, certain modules may not be listed by certain approval agencies, or listing may be in process. Consult factory for latest listing status. • UL Listed: file S521. • CSFM approved: file 7300-1288:169. • MEA approved: file 368-01-E Vol. II. Product Line Information PIM-SS: Ten-input monitor module. BB-25: Optional cabinet for up to six modules mounted on CHS-6 chassis (below). Dimensions, DOOR: 24.0" (60.96 cm) wide x 12.632" (32.0852 cm) high, x 1.25" (3.175 cm) deep, hinged at bottom; BACKBOX: 24.0" (60.96 cm) wide x 12.550" (31.877 cm) high x 5.218" (13.2537 cm) deep. CHS-6: Chassis, mounts up to six modules in a BB-25 cabinet. PIM-SS CS-2468 09/01/06 Page 1 of 2 Specifications Standby current: 3.5 mA (SLC current draw with all addresses used; if some addresses are disabled, the standby current decreases). Alarm current: 55 mA (assumes all ten LEDs solid ON). Temperature range: 32°F to 120°F (0°C to 49°C) for UL applications Humidity: 10% to 85% noncondensing for UL applications Dimensions: 6.8" (172.72 mm) high x 5.8" (147.32 mm) wide x 1.25" (31.75 mm) deep. Shipping weight: 1.1 lb. (0.499 kg) including packaging. Mounting options: CHS-6 chassis, BB25 cabinet, or suitably grounded metallic cabinet. Wire gauge: 12 AWG (3.25 mm²) to 18 AWG (0.9 mm²). Power-limited circuits m ust employ type FPL, FPLR, or FPLP cable as required by Article 760 of the NEC. PIM-SS is shipped in Class B position; remove shunt for Class A operation. Maximum IDC wiring resistance: 1500 ohms. Maximum IDC voltage: 12 VDC. Maximum IDC current: 1 mA. FIGURE 1: Typical Initiating Device Circuit Configuration — Class B, Style B. NOTE: Any number of UL-Listed contact closure devices may be used. DO NOT MIX fire alarm initiating and supervisory devices on the same initiating device circuit. Install contact closure devices per manufacturer’s installation instructions. 52347w1.wmf 52347w2.wmf FIGURE 2: Typical Fault-Tolerant Initiating Device Circuit Configuration — Class A, Style D. NOTE: Any number of UL-Listed contact closure devices may be used. DO NOT MIX fire alarm initiating and supervisory devices on the same initiating device circuit. Install contact closure devices per manufacturer’s installation instructions. Gamewell-FCI 12 Clintonville Road Northford, CT 06472-1610 Phone: 203-484-7161 Fax: 203-484-7118 www.gamewell-fci.com A Honeywell Company © 2006 Gamewell-FCI Specifications and wiring information are provided for information only and are believed to be accurate. Gamewell-FCI assumes no responsibility for their use. Data and design are subject to change without notice. Installation and wiring instructions shipped with the product shall always be used for actual installation. For more information, contact Gamewell-FCI. Page 2 of 2 PIM-SS CS-2468 09/01/06

下载 PDF

BB-25

1. 物料型号： - 型号：PIM-SS，为十输入监控模块。

2. 器件简介： - Gamewell的SmartScan™PIM-SS十输入监控模块提供了一个接口，用于连接控制面板和智能报警系统中的常开接触设备，例如传统的拉杆站和热探测器。

3. 引脚分配： - 可移除的12 AWG（3.25 mm²）至18 AWG（0.9 mm²）的插入式端子块。

4. 参数特性： - 待机电流：3.5 mA（如果一些地址被禁用，则待机电流会降低）。 - 报警电流：55 mA（假设所有十个LED常亮）。 - 温度范围：UL应用为32°F至120°F（0°C至49°C）。 - 湿度：UL应用为10%至85%非凝结。 - 尺寸：6.8"（172.72 mm）高 x 5.8"（147.32 mm）宽 x 1.25"（31.75 mm）深。 - 运输重量：1.1 lb.（0.499 kg），包括包装。 - 端子线规：12 AWG（3.25 mm²）至18 AWG（0.9 mm²）。

5. 功能详解： - 提供十个可寻址的B类或五个可寻址的A类启动设备电路。 - 每个点都有状态指示器。 - 未使用的地址可以被禁用。 - 旋转地址开关。 - 可进行A类或B类操作。

6. 应用信息： - 与Gamewell的IF602、610、632、654和658配合SmartScan™回路卡使用。 - 可以单独安装一个或两个模块在BB-XP机柜中（可选）。 - 可以在BB-25机柜中的CHS-6底盘上安装多达六个模块（可选）。

7. 封装信息： - 封装选项包括CHS-6底盘、BB25机柜或适当接地的金属机柜。 - PIM-SS在B类位置发货；移除旁路即可进行A类操作。

BB-25 价格&库存

-> 查询更多价格&库存

很抱歉，暂时无法提供与“BB-25”相匹配的价格&库存，您可以联系我们找货

免费人工找货