GM1937ST25RG

GM1937 WHITE LED STEP-UP CONVERTER Description The GM1937 is a step-up DC/DC converter specifically designed to drive white LEDs with a constant current. The device can drive two, three or four LEDs in series from a Li-Ion cell. Series connection of the LEDs provides identical LED currents resulting in uniform brightness and eliminating the need for ballast resistors. The output capacitor can be as small as 0.22µF, saving space versus alternative solutions. A low 95mV feedback voltage minimizes power loss for better Features High Efficiency: 84% Typical 36V internal Switch Fast 1.2MHz Switching Frequency Drives Up to three LEDs from a 2.8V Supply Drives Up to six LEDs from a 5V Supply External Matched LED Current Uses Tiny 1mm height inductor Requires Only 0.22 　 F Output Capacitor Low profile TSOT package Application Cellular Phones PDA, Handheld Computers Digital Cameras MPS3 Players GPS Receivers T ypical Application Circuits VIN 3V to 5V 1µ F VIN 22µH 90 EFFICIENCY (%) SW 0.22µF 85 80 75 70 65 60 0 5 10 15 LED CURRENT (mA) 20 VIN = 3.0V VIN = 3.6V OFF ON GM1937 FB CE GND R1 6.34Ω Figure 1 Li-Ion Powered Driver for Three White LEDs 1 GM1937V2.00 GM1937 WHITE LED STEP-UP CONVERTER Marking Information and Pin Configurations (Top View) SOT25 VCC 5 CE 4 WLYWA 1 SW 2 GND 3 FB WL: Device Code, Green Product Y: Year W: Week code A: Assembly/testing site Pin Descriptions Pin Number 1 2 3 Pin Name SW GND FB Ground Pin Function Switch Pin, (Minimize trace area at this pin to reduce EMI.) Feedback Pin. Reference voltage is 95 mV. (Calculate resistor value according to the formula RFB=95 mV / ILED .) Shutdown Pin (Connect to 1.5 V or higher to enable device; 0.4 V or less to disable device) Input Supply Pin. (Must be locally bypassed) 4 5 CE VCC Order Information Ordering Number GM1937ST25RG Package SOT-25 Shipping 3,000 Units/Tape and Reel GM1937V2.00 2 GM1937 WHITE LED STEP-UP CONVERTER Absolute Maximum Ratings PARAMETER Input Voltage SW Voltage FB Voltage CE Voltage Continuous Total Power Dissipation Operating Ambient Temperature Storage Temperature Lead Temperature (Soldering, 10 sec) SOT-25 PD TA Tstg SYMBOL VIN RATINGS 10 36 10 10 300 - 40 to 85 - 65 to 150 + 300 UNITS V V V V mW ℃ ℃ ℃ B lock Diagram VIN 5 FB 3 COMPARATOR VREF 1.25V 95mV RC CC 0.2Ω R S Q SW 1 DRIVER Q1 RAMP GENERATOR CE 4 SHUTDWON 1.2MHz OSCILATOR 2 GND Figure 2 3 GM1937V2.00 GM1937 WHITE LED STEP-UP CONVERTER Electrical Characteristics (TA = 25℃, Vcc = 3V, VCE = 3V, Parameter Feeback Voltage FB Pin Bias Current Supply Current Switching Frequency Maximum Duty Cycle Switch Current Limit Switch VCESAT Switch Leakage current CE Voltage High CE Voltage Low CE Pin Bias Current ICE Symbol VFB IFB ICC(ON) ICC(OFF) fSW DMAX ISW VSAT ILEAK ISW = 250mA VSW = 5V VCE = 0V Condition ISW = 100mA, Duty Cycle = 66% unless otherwise noted) Min 86 10 Typ 95 45 1.9 0.1 0.8 85 1.2 90 320 350 0.00 1 1.5 0.4 65 Max 104 100 2.5 1.0 1.6 Unit mV nA mA µA MHz % mA mV 5 µA V V µA GM1937V2.00 4 GM1937 WHITE LED STEP-UP CONVERTER A pplication Information Operation GM1937 is designed with a constant frequency, current mode control scheme to provide excellent line and load regulation. Operation can be best understood by referring to the block diagram in Figure 2. At the start of each oscillator cycle, the SR latch is set, which turns on the power switch Q1. A voltage proportional to the switch current is added to a stabilizing ramp and the resulting sum is fed into the positive terminal of the PWM comparator A2. When this voltage exceeds the level at the negative input of A2, the SR latch is reset turning off the power switch. The level at the negative input of A2 is set by the error amplifier A1, and is simply an amplified version of the difference between the feedback voltage and the reference voltage of 95mV. In this manner, the error amplifier sets the correct peak current level to keep the output in regulation. If the error amplifier’s output increases, more current is delivered to the output; if it decreases, less current is delivered. Minimum Output Current GM 1937 can regulate three series LEDs connected a low output current. down to approximately 4mA from a 4.2V supply, without pulse skipping, using the same external components as specified for 15mA operation. As current is further reduced, the device will begin skipping pulses.This will result in some low frequency ripple, although the LED current remains regulated on an average basis down to zero. Inductor Selection A 22mH inductor is recommended for most GM1937 applications. Although small size and high efficiency are major concerns, the inductor should have low core losses at 1.2MHz and low DCR (copper wire resistance). Some inductors in this category with small size are listed in Table 1. Table 1. Recommended Inductors Part Number LQH3C220 ELJTC220KF CDRH3D16-220 LB2023B220M LEM2520-220 DCR (Ω) 0.71 4.0 0.53 1.7 5.5 Current Rating (mA) 250 160 350 75 125 Manufacturer Murata Panasonic Sumida Taiyo Yuden Taiyo Yuden Capacitor Selection The small size of ceramic capacitors makes them ideal for GM1937 applications. X5R and X7R types are recommended because they retain their capacitance over wider voltage and temperature ranges than other types such as Y5V or Z5U. A 1µF input capacitor and a 0.22µF output capacitor are sufficient for most GM1937 applications. 5 GM1937V2.00 GM1937 WHITE LED STEP-UP CONVERTER A pplication Information – Cont’d Diode Selection Schottky diodes, with their low forward voltage drop and fast reverse recovery, are the ideal choices for GM1937 applications. The forward voltage drop of a Schottky diode represents the conduction losses in the diode, while the diode capacitance (CT or CD) represents the switching losses. For diode selection, both forward voltage drop and diode capacitance need to be considered. Schottky diodes with higher current ratings usually have lower forward voltage drop and larger diode capacitance, which can cause significant switching losses at the 1.2MHz switching frequency of the LT1937K. A Schottky diode rated at 100mA to 200mA is sufficient for most GM1937 applications. Some recommended Schottky diodes are listed in Table 2. Table 2. Recommended Schottky Diodes Part Number CMDSH-3 CMDSH2-3 BAT54 Forward Current (mA) 100 200 200 Voltage Drop (V) 0.58 @ 100mA 0.49 @ 200mA 0.53 @ 100mA Diode Capacitance (pF) 7.0 @10V 15 @10V 10 @25V Manufacturer Central Central Zetex LED Current Control The LED current is controlled by the feedback resistor (R1 in Figure 1). The feedback reference is 95mV. The LED current is 95mV/R1. In order to have accurate LED current, precision resistors are preferred (1% is recommended). The formula and table for R1 selection are shown below.R1 = 95mV/ILED Table 3. R1 Resistor Value Selection ILED (mA) 5 10 12 15 20 R1 (Ω) 19.1 9.53 7.87 6.34 4.75 Open-Circuit Protection In the cases of output open circuit, when the LEDs are disconnected from the circuit or the LEDs fail, the feedback voltage will be zero. The GM1937 will then switch at a high duty cycle resulting in a high output voltage, which may cause the SW pin voltage to exceed its maximum 36V rating. A zener diode can be used at the output to limit the voltage on the SW pin (Figure 3). The zener voltage should be larger than the maximum forward voltage of the LED string. The current rating of the zener should be larger than L 0.1mA. 22 µ H D VIN GM1937V2.00 CIN 1µ F VIN GM1937 SW R2 1K R1 6.34Ω COUT 0.22µF FB CE GND 6 Figure 3. LED Driver with Open-Circuit Protection GM1937 WHITE LED STEP-UP CONVERTER A pplication Information – Cont’d Dimming Control There are four different types of dimming control: 1. Using a PWM Signal to SHDN Pin With the PWM signal applied to the CE pin, the GM1937 is turned on or off by the PWM signal. The LEDs operate at either zero or full current. The average LED current increases proportionally with the duty cycle of the PWM signal. A 0% duty cycle will turn off the GM1937 and corresponds to zero LED current. A 100% duty cycle corresponds to full current. The typical frequency range of the PWM signal is 1kHz to 10kHz. The magnitude of the PWM signal should be higher than the minimum CE voltage high. 2. Using a DC Voltage For some applications, the preferred method of brightness control is a variable DC voltage to adjust the LED current. The dimming control using a DC voltage is shown in Figure 4. As the DC voltage increases, the voltage drop on R2 increases and the voltage drop on R1 decreases. Thus, the LED current decreases. The selection of R2 and R3 will make the current from the variable DC source much smaller than the LED current and much larger than the FB pin bias current. For VDC range from 0V to 2V, the selection of resistors in Figure 4 gives dimming control of LED current from 0mA to 15mA. GM1937 R3 90K FB R2 5K R1 6.34Ω R3 90K 0.1µF GM1937 FB R2 5K R1 6.34Ω VDC PWM 10K Figure 4. Dimming Control Using a DC Voltage Figure 5. Dimming Control Using a Filtered PWM Signal 3. Using a Filtered PWM Signal The filtered PWM signal can be considered as an adjustable DC voltage. It can be used to replace the variable DC voltage source in dimming control. The circuit is shown in Figure 5. 4. Using a Logic Signal For applications that need to adjust the LED current is discrete steps, a logic signal can be used as shown in Figure 6. R1 sets the minimum LED current (when the NMOS is OFF). RINC sets how much the LED current increases when the NMOS is turned on. The selection of R1 and RINC can be found in table 3 GM1937 FB RINC Logic Signal R1 Figure 5. Dimming Control Using a Logic Signal 7 GM1937V2.00 GM1937 WHITE LED STEP-UP CONVERTER Package Outline Dimensions – SOT 25 2.9 ± 0.1 1.9 ± 0.05 0.95 ± 0.038 0.13 Pad Layout 0~0.1 2.8 ± 0.1 1.5 ± 0.05 0 .028 0 .7 0 .039 1 .0 0.65 ± 0.05 0 .094 2.4 0.35 ± 0.03 0.8 ± 0.05 0 .037 0 .95 0 .037 0 .95 0 .074 1 .9 5° 5° (Inches ) mm 1.10 ± 0.1 Unit:mm GM1937V2.00 8 GM1937 WHITE LED STEP-UP CONVERTER O rdering Number G M 1937 ST25 R APM Gamma Micro Circuit Type Package Type ST25: SOT 25 Shipping Type G Blank: Pb-free G:Green R: Tape & Reel Note: Pb-free products: ♦ ♦ ♦ ♦ RoHS compliant and compatible with the current require-ments of IPC/JEDEC J-STD-020. Suitable for use in SnPb or Pb-free soldering processes with 100% matte tin (Sn) plating. Lead-free (RoHS compliant) Halogen free(Br or Cl does not exceed 900ppm by weight in homogeneous material and total of Br and Cl does not exceed 1500ppm by weight) Green products: 9 GM1937V2.00