GM339D14T

GM339 LOW POWER QUAD DIFFERENTIAL COMPARATOR Description The GM393 consists of four independent precision voltage comparators which were designed specifically to operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude of the power supply voltage. These comparators also have a unique characteristic. In that, the input commonmode voltage range includes ground, even though operated from a single power supply voltage. Application areas include limit comparators, simple analog to digital converters; pulse, square wave and time delay generators; wide range VCO; MOS clock timers; multivibrators and high voltage digital logic gates. The GM339 are designed to directly interface with TTL and CMOS. When operated from both plus and minus power supplies, the GM339 will directly interface with MOS logic, where their low power drain is a distinct advantage over standard comparators. The GM339 is available in DIP-8 and SOP-8 packages. Features Single- supply Range: ±1.0V to ±18V Wide supply voltage range: ±2.0V to ±36V Very low supply current drain (0.4 mA) independent of supply voltage Low input biasing current: 25 nA Low input offset current: ±5 nA Maximum offset voltage: ±3 mV Input common-mode voltage range includes ground Differential input voltage range equal to the power supply voltage Low output saturation voltage: 250 mV at 4 mA Output voltage compatible with TTL, DTL, ECL, MOS and CMOS logic systems Connecting Diagram (Top View) OUT COMP 1 1 14 OUT COMP 3 OUT COMP 2 VCC 2 3 4 5 6 7 SOP-14, DIP-14 PACKAGE 13 OUT COMP 4 12 GND 11 COMP 4 IN10 COMP 4 IN+ 9 8 COMP 3 INCOMP 3 IN+ COMP 2 INCOMP 2 IN+ COMP 1 IN- GM339V1.00 COMP 1 IN+ 2 GM339 LOW POWER QUAD DIFFERENTIAL COMPARATOR Marking Information and Pin Configurations (Top View) SO14 and DIP14 1. OUT COMP 1 2. OUT COMP 2 3. VCC 4. COMP 2 IN5. COMP 2 IN+ 6. COMP 1 IN 7. COMP 1 IN+ 14. OUT COMP 3 13. OUT COMP 4 12. GND 11. COMP4 IN+ 10. COMP4 IN9. COMP 3 IN+ 8. COMP 3 IN- A: Assembly / Test site code Y: Year WW: Week GM339 AYWW Ordering Information Ordering Number GM339D14T GM339S14T GM339S14R Package DIP-14 SO-14 SO-14 Shipping 25 Units / Tube 50 Units / Tube 2,500 Units / Tape & Reel GM339V1.00 3 GM339 LOW POWER QUAD DIFFERENTIAL COMPARATOR Absolute Maximum Ratings PARAMETER Supply Voltage Input Current Input Voltage Operating Temperature Range Storage Temperature Lead Temperature (soldering 10 sec.) RATINGS ±18 or 36 50 -0.3 to +32 -40 to 125 - 65 to 150 260 UNITS V mA V ℃ ℃ ℃ B lock Diagram VCC VIN + VOUT VIN - GM339V1.00 4 GM339 LOW POWER QUAD DIFFERENTIAL COMPARATOR Electrical Characteristics (VCC = 5V, at specified free-air temperature, unless otherwise specified) Parameter Input offset Voltage Symbol VIO Condition VCC = 5V to Max VIC = VICR min VO = 1.4V VO = 1.4V TA = 25℃ Full Range TA = 25℃ Full Range TA = 25℃ Full Range TA = 25℃ Full Range IOL = 4mA, VID = 1V VCC = 15V, VO = 1V to 11V RL = 15K to VCC VOH = 5V, VID = 1V VOH = 30V, VID = 1V VOH = 1.5V, VID = -1V RL = ∞, VCC = 5V RL = ∞, VCC = 30V RL Connected to 5V through 5.1k. CL = 15pF TA = 25℃ Full Range TA = 25℃ TA = 25℃ Full Range TA = 25℃ TA = 25℃ Full Range 100mV input step with 5mV overdrive TTL - level input step Min Typ ±2 Max ±5 9 Unit mV Input Offest Current IIO ±5 ±50 ±150 nA Input Bias Current Common-Mode Input Voltage Range** Low-Level output Voltage Large-Signal Differential Voltage Amplification High Level Output Current Low Level Output Current Supply Current IIB VO =1.4V -20 -250 400 nA VICR 0 to VCC-1.5V 0 to VCC-2.0V 150 400 700 50 200 0.1 1 6 0.8 1.0 2.5 1.3 50 V VOL mV AVD V/mV nA µA mA mA IOH IOL ICC Response Time (Note 1) µs 0.3 All characteristics are measured under open loop conditions with zero common-mode input voltage unless otherwise specified. "MAX" VCC for testing purposes is 30V. Full range is 0°C to 70°C. ** The voltage at either input or common - mode should not be allowed to go negative by more than 0.3V. The upper end of the common - mode voltage range is VCC - 1.5V, but either or both inputs can go to 30V without damage. Note 1: CL includes probe and jig capacitance. The response time specified is the interval between the input step function and the instant when the output crosses 1.4V. GM339V1.00 5 GM339 LOW POWER QUAD DIFFERENTIAL COMPARATOR T ypical Performance Characteristics 80 70 IIB, Input Bias Current (nA) 60 50 40 30 20 10 0 0 5 10 15 20 25 30 35 40 TA = 125°C TA = -55°C TA = 0°C TA = 25°C TA = 70°C VOL, Saturation Voltage (VDC) 1.0 TA = 125°C 0.1 TA = 25°C 10 Out of Saturation TA = -55°C 0.01 0.001 0.01 0.1 1.0 10 100 VCC, Supply Voltage (VDC) Figure 1. Input Bias Current versus Power Supply Voltage ISINK, Output Sink Current (mA) Figure 2. Output Saturation Voltage v.s. Output Sink Current 1.0 TA = -55°C TA = 0°C TA = 25°C 0.8 ICC, Supply Current (mA) 0.6 TA = 70°C 0.4 0.2 0.0 0 TA = 125°C RL = ∞ 5 10 15 20 25 30 35 40 VCC, Supply Voltage (VDC) Figure 3. Power Supply Current versus Power Supply Voltage GM339V1.00 6 GM339 LOW POWER QUAD DIFFERENTIAL COMPARATOR Package Outline Dimensions – SO 14 0.335 - 0.344 (8.509 - 8.738) 0.228 - 0.244 (5.791 - 6.198) 0.050 (1.270) TYP. 0.014 - 0.020 (0.356 - 0.508) 0.053 - 0.069 (1.346 - 1.753) 0.150 - 0.157 (3.810 - 3.988) SEATING PLAN 8 Max 0.014 (0.356) TYP. 0.008 - 0.010 (0.,203 - 0.254) Package Outline Dimensions – DIP 14 14 8 0.220 - 0.310 (5.588 - 7.874) 1 7 0.785 (19.939) MAX 0.290 - 0.320 (7.366 - 8.128) 0.060 +/- 0.005 (1.524 +/- 0.127) 0.200 (5.080) MAX 0.150 (3.810) MIN 0.098 (2.489) MAX BOTH ENDS 0.008 - 0.012 (0.203 - 0.305) 10 MAX 0.100 +/- 0.010 (2.540 +/- 0.254) 0.018 +/- 0.003 (0.457 +/- 0.076) GM339V1.00 7 GM339 LOW POWER QUAD DIFFERENTIAL COMPARATOR O rdering Number GM APM Gamma Micro 339 Circuit Type S14 Package Type S14: SO 14 D14: DIP 14 R Shipping Type R: Taping & Reel T: Tube GM339V1.00 8 1