GM6155-AST25R

Description GM6155 is an efficient linear voltage regulator with ultralow - noise output, very low dropout voltage (typically 17mV at light loads and 165mV at 50mA), and very low ground current (600µA at 100mA output). GM6155 provides better than 1% initial accuracy. Designed especially for hand-held, battery-powered devices, GM6155 includes a CMOS or TTL compatible enable/ shutdown control input. When shutdown, power consumption drops nearly to zero. Regulator ground current increases only slightly in dropout, further prolonging battery life. Key features of GM6155 include a reference bypass pin to improve its excellent low-noise performance, reversed-battery protection, current limiting, and overtemperature shutdown. The GM6155 is available in SOT-25 package. Features Ultra low noise output High output voltage accuracy Extremely accurate output voltage Guaranteed 150mA output Low quiescent current Low dropout voltage Extremely tight load and line regulation Very low temperature coefficient Current and thermal limiting Reverse-battery protection "Zero" off-mode current Logic-controlled electronic enable Application Cellular telephones Laptop, notebook, and palmtop computers Battery-powered equipment PCMCIA VCC and VPP regulation/ switching Consumer/ personal electronics SMPS post-regulator/ dc-to-dc modules High-efficiency linear power supplies TYPICAL APPLICATION CIRCUITS 2 Enable Shutdown 3 EN GM6155-3.3 VIN 1 5 VOUT 4 CBYP EN (pin 3) may be connected directly to IN (pin1). Low-Noise Operation: CBYP = 470pF, COUT Basic Operation: CBYP = not used, COUT 2.2µF 1µF www.gammamicro.com GM6155 V0.1 1 COUT = 2.2µF (tantalum) MARKING INFORMATION & PIN CONFIGURATIONS (TOP VIEW) SOT-25 (SOT-23-5) OUT 5 SOT-25 (SOT-23-5) OUT 5 BYP 4 ADJ 4 Part Identification XXVYW 1 2 3 1 XXVYW 2 3 IN GND EN IN GND EN Fixed Voltages Adjustable Voltage XX V Y W = Marking Code(DA = GM6155) = Voltage Code = Year = Weekly ORDERING INFORMATION O rdering Number GM6155-AST25R GM6155-2.5ST25R GM6155-2.7ST25R GM6155-2.8ST25R GM6155-2.9ST25R GM6155-3.0ST25R GM6155-3.3ST25R GM6155-3.6ST25R GM6155-4.0ST25R GM6155-4.2ST25R GM6155-5.0ST25R Output Voltage Voltage Code Adj 2.5V 2.7V 2.8V 2.9V 3.0V 3.3V 3.6V 4.0V 4.2V 5.0V A G T H X J K L M Y Q Package SOT-25 SOT-25 SOT-25 SOT-25 SOT-25 SOT-25 SOT-25 SOT-25 SOT-25 SOT-25 SOT-25 Shipping 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel * For detail Ordering Number identification, please see last page. PIN DESCRIPTION Pin Number 1 2 3 Pin Name IN GND EN Function Supply Input Ground Enable/ Shutdown(Input): COMS compatible input. Logic high = enable, logic low or open = shutdown. Reference Bypass: Connect external 470pF capacitor to GND to reduce output noise. May be left open. Regulator Output GM6155 4 5 BYP OUT 2 BLOCK DIAGRAM VIN IN BYP OUT + + Bandgap Ref. VOUT COUT CBYP (Optional) VIN IN OUT + ADJ + R2 Bandgap Ref. VOUT COUT EN R1 Current Limit Thermal Shutdown CBYP (Optional) GND EN VOUT = VREF (1 + R2/ R1) Current Limit Thermal Shutdown Figure 1. Ultra-Low-Noise Fixed Regulator GND Figure 2. Ultra-Low-Noise Adjustable Regulator ABSOLUTE MAXIMUM RATINGS PARAMETER Supply Input Voltage Enable Input Voltage Power Dissipation (Note 3) Junction Temperature Lead Temperature (soldering, 5 seconds) Storage Temperature SYMBOL VIN VEN PD TJ TLEAD TS RATINGS -20 ~ + 20 -20 ~ +20 Internally Limited -40 ~ +125 260 -60 ~ +150 UNITS V V W °C °C °C OPERATING RATINGS PARAMETER Supply Input Voltage Enable Input Voltage Junction Temperature Thermal Resistance SYMBOL VIN VEN TJ qJA RATINGS +2.5 to +16 0 to VIN -40 ~ + 125 (Note 3) UNITS V V °C °C/ W GM6155 3 ELECTRICAL CHARACTERISTICS (VIN = VOUT + 1V; IL = 100µA; CL = 1.0µF; VEN unless otherwise noted) 2.0; TJ = 25°C, bold values indicate -40°C TJ +125°C; Parameter Output Voltage Accuracy Output Voltage Temperature Coefficient Line Regulation Load Regulation Symbol VO DVO/ DT DVO/ VO DVO/ VO Test Condition Variation from specified VOUT (Note 4) VIN = VOUT + 1V to 16V IL = 0.1mA to 150mA, (Note 5) IL = 100µA IL = 50mA Min -1 -2 Typ Max 1 2 Unit % ppm/ °C 40 0.004 0.02 10 110 140 165 0.01 80 350 600 1300 75 320 0.05 260 500 0.012/ 0.05 0.2/ 0.5 50 70 150 230 250 300 275 350 1 5 125 150 600 800 1000 1500 1900 2500 %/ V % Dropout Voltage (Note 6) VIN - VO IL = 100mA IL = 150mA mV Quiescent Current IGND VEN VEN VEN 0.4V (shutdown) 0.18V (shutdown) 2.0V, IL = 0.1mA IL = 50mA µA Ground Pin Current (Note 7) IGND IL = 100mA IL = 150mA µA Ripple Rejection Current Limit Thermal Regulation Output Noise ENABLE Input Enable Input Logic-Low Voltage Enable Input Logic-High Voltage PSRR ILIMT DVO/ DPD eNO f = 100Hz, IL = 0.1mA VOUT = 0V (Note 8) IL = 50mA, CL = 2.2µF, 470pF from BYP to GND dB mA %/ W nV/ Hz VIL VIH IIL Regulator shutdown Regulator enabled VIL VIL VIH 0.4V 0.18V 2.0V 2 5 2.0 0.01 0.4 0.18 V V -1 -2 20 25 µA µA Enable Input Current IIH GM6155 4 Note 1. Exceeding the absolute maximum rating may damage the device. Note 2. The device is not guaranteed to function outside its operating rating. Note 3: The maximum allowable power dissipation at any TA (ambient temperature) is PD(max) = (TJ(max) -TA) qJA. Exceeding the maximum allowable power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown. Note 4: Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range. Note 5: Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for load regulation in the load range from 0.1mA to 150mA. Changes in output voltage due to heating effects are covered by the thermal regulation specification. Note 6: Dropout Voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at 1V differential. Note 7: Ground pin current is the regulator quiescent current plus pass transistor base current. The total current drawn from the supply is the sum of the load current plus the ground pin current. Note 8: Thermal regulation is defined as the change in output voltage at a time "t" after a change in power dissipation is applied, excluding load or line regulation effects. Specifications are for a 150mA load pulse at VIN = 16V for t = 10ms. Applications Information Enable/ Shutdown Forcing EN (enable/ shutdown) high (>2V) enables the regulator. EN is compatible with CMOS logic gates. If enable shutdown feature is not required, connect EN (pin 3) to IN (supply input, pin 1). See Figure 3. Input Capacitor A 1µF capacitor should be placed from IN to GND if there is more than 10 inches of wire between the input and the acfilter capacitor or if a battery is used as the input . Reference Bypass Capacitor BYP (reference bypass) is connected to the internal voltage reference. A 470pF capacitor (CBYP) connected from BYP to GND quiets this reference, providing a significant reduction in output noise. CBYP reduces the regulator phase margin, when using CBYP, output capacitors of 2.2µF or greater are generally required to maintain stability. The start-up speed of GM6155 is inversely proportional to the size of the reference bypass capacitor. Applications requiring a slow ramp-up of output voltage should consider larger values of CBYP. Likewise, if rapid turn-on is necessary, consider omitting CBYP. If output noise is not a major concern, omit CBYP and leave BYP open. Output Capacitor An output capacitor required between OUT and GND to prevent oscillation. The minimum size of the output capacitor is dependent upon whether a reference bypass capacitor is used. 1.0µF minimum is recommended when CBYP is not used (see Figure 2). 2.2µF minimum is recommended when CBYP is 470pF (see Figure 1). Larger values improve the regulator's transient response, the output capacitor value may be increased without limit. The output capacitor should have an ESR (effective series resistance) of about 5W or less and a resonant frequency above 1MHz. Ultra-low-ESR capacitors can cause a low amplitude oscillation on the output and/ or underdamped transient response. Most tantalum or aluminum electrolytic capacitors are adequate; film types will work, but more expensive. Since many aluminum electrolytics have electrolytes that freeze at about -30°C, solid tantalums ate recommended for operation below -25°C. At lower values for output current, less output capacitance is required for output stability. The capacitor can be reduced to 0.47µF for current below 10mA or 0.33µF for current below 1mA. No-Load Stability GM6155 will remain stable and in regulation with no load (other than the internal voltage divider) unlike many other voltage regulators. This is especially important in CMOS RAM keep-alive applications. Thermal Considerations Gm6155 is designed to provide 150mA of continuous current in a very small package. Maximum power dissipation can be calculated based on the output current and the voltage drop across the part. To determine the maximum power dissipation of the package, use the junction-to-ambient thermal resistance of the device and the following basic equation: PD(max) = (TJ(max) - TA) RqJA TJ(max) is the maximum junction temperature of the die, 125°C, and TA is the ambient operating temperature. RqJA is layout dependent; Table 1 shows examples of junction-to-ambient thermal resistance for the GM6155. GM6155 5 Parameter SOT-23-5 RqJA Recommended Minimum Footprint 220°C/ W RqJA 1" Square Copper Clad 170°C/ W RqJC 130°C/ W Table 1. SOT-25 Thermal Resistance The actual power dissipation of the regulator circuit can be determined by using the equation: PD = (VIN - VOUT) IOUT + VIN IGND Substituting PD(max) for PD and solving for the operating conditions that are critical to the application will give the maximum operating conditions for the regulator circuit. For example, when operating Gm6155 at room temperature with a minimum footprint layout, the maximum input voltage for a set output current can be determined as follows: (125°C - 25°C) PD(max) = 220°C/W PD(max) = 455mW The junction-to-ambient thermal resistance for the minimum footprint is 220°C/ W, from Table 1. The maximum power dissipation must not be exceeded for proper operation. Using the output voltage of 3.3V and an output current of 150mA, the maximum input voltage can be determined. From the Electrical Characteristics table, the maximum ground current for150mA output current is 2500µA or 2.5mA. 455mW = (VIN - 3.3V) 150mA + VIN • 2.5mA 455mW = VIN • 150mA - 495mA + VIN • 2.5mA 950mW = VIN • 152.5mA VIN(max) = 6.23V Therefore, a 3.3V application at 150mA of output current can accept a maximum input voltage of 6.2V in a SOT-25 package. For a full discussion of heat sinking and thermal effects on voltage regulators. Fixed Regulator Applications Figure 3. Ultra-Low-Noise Fixed Voltage Application VIN 1 2 3 5 VOUT 2.2µF 4 470pF Enable Shutdown Figure 4. Low-Noise Fixed Voltage Application VIN 1 2 3 EN 5 VOUT 1.0µF 4 GM6155 GM6155 Figure 3. includes a 470pF capacitor for low-noise operation and shows EN (pin 3) connected to IN (pin 1) for an application where enable/ shutdown is not required. COUT = 2.2µF minimum. Figure 4. is an example of a low-noise configuration where CBYP is not required. C OUT = 1µF minimum. Adjustable Regulator Applications The GM6155 can be adjusted to a specific output voltage by using two externa resistors (Figure 5). The resistors set the output voltage based on the following equation: VOUT = 1.242V X ( R2 +1) R1 6 GM6155 This equation is correct due to the configuration of the bandgap reference. The bandgap voltage is relative to the output, as seen in the block diagram. Traditional regulators normally have the reference voltage relative to ground and have a different VOUT equation. Resistor values are not critical because ADJ(adjust) has a high input impedance, but for best results use resistors of 470kW or less for best results. A capacitor from ADJ to ground provides greatly improved noise performance. 1 2 3 GM6155-Adj VIN 5 R1 4 R2 VOUT 2.2µF 470pF Figure 5. Ultra-Low- Noise Adjustable Voltage Application Figure 5 includes the optional 470pF noise bypass capacitor from ADJ to GND to reduce output noise. Dual-Supply Operation When used in dual supply systems where the regulator load is returned to a negative supply, the output voltage Typical Characteristics 0 V = 6V IN VOUT = 5V -20 PSRR (dB) 0 V = 6V IN VOUT = 5V -20 PSRR (dB) -40 -60 -80 -40 -60 -80 IOUT =100mA COUT = 2.2µF CBYP = 0.01µF 100 1k 10k 100k 1M 10M FREQUENCY(Hz) -100 10 IOUT =100mA COUT = 1µF 100 1k 10k 100k 1M 10M FREQUENCY(Hz) -100 10 Figure 6. Power Supply Rejection Ratio 320 280 DROPOUT VOLTAGE (mV) Figure 7. Power Supply Rejection Ratio 10 125°C 1 25°C -40°C NOISE (µV/ Hz) 240 200 160 120 80 40 0 0 40 80 120 160 100mA 0.1 10mA 0.01 1mA 10k 100k 1M 10M OUTPUT CURRENT (mA) FREQUENCY(Hz) Figure 8. Dropout Voltage vs. Output Current Figure 9. Noise Performance GM6155 7 VOUT=5V 0.001 COUT=10µF electrolytic C =10nF 0.0001 BYP 10 100 1k SOT-25(SOT-23-5) PACKAGE OUTLINE DIMENSIONS 2.9 ± 0.1 1.9 ± 0.05 0.95 ± 0.038 0.13 Pad Layout 0~0.1 1.5 ± 0.05 2.8 ± 0.1 0.094 2.4 0.028 0.7 0.039 1.0 0.65 ± 0.05 0.35 ± 0.03 0.8 ± 0.05 0.037 0.95 0.037 0.95 5° 5° 0.074 1.9 ( Inches ) mm 1.10 ± 0.1 Unit:mm ORDERING NUMBER GM 6155 A ST25 R Gamma Micro. Circuit Type Shipping R: Tape & Reel GM6155 Output Voltage A: Adj, 2.5: 2.5V 2.7: 2.7V, 2.8: 2.8V 2.9: 2.9V, 3.0: 3.0V 3.3: 3.3V, 3.6: 3.6V 4.0: 4.0V, 4.2: 4.2V Package ST25: SOT-25 8 9 GM6155