1N4003

1N4001 THRU 1N4007 GENERAL PURPOSE PLASTIC RECTIFIER Reverse Voltage - 50 to 1000 Volts DO-204AL Forward Current - 1.0 Ampere FEATURES 1.0 (25.4) MIN. 0.107 (2.7) 0.080 (2.0) DIA. 0.205 (5.2) 0.160 (4.1) ♦ The plastic package carries Underwriters Laboratory Flammability Classification 94V-0 ♦ Construction utilizes void-free molded plastic technique ♦ Low reverse leakage ♦ High forward surge current capability ♦ High temperature soldering guaranteed: 250°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension MECHANICAL DATA 1.0 (25.4) MIN. 0.034 (0.86) 0.028 (0.71) DIA. NOTE: Lead diameter is 0.026 (0.66) 0.023 (0.58) for suffix "E" part numbers Case: JEDEC DO-204AL molded plastic body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.012 ounce, 0.3 gram Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS 1N 4001 1N 4002 1N 4003 1N 4004 1N 4005 1N 4006 1N 4007 UNITS *Maximum repetitive peak reverse voltage *Maximum RMS voltage *Maximum DC blocking voltage *Maximum average forward rectified current 0.375" (9.5mm) lead length at T A=75°C *Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) TA=75°C *Maximum instantaneous forward voltage at 1.0A *Maximum full load reverse current full cycle average 0.375" (9.5mm) lead length at TL=75°C *Maximum DC reverse current at rated DC blocking voltage Typical reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Typical thermal resistance (NOTE 3) Maximum DC blocking voltage temperature *Operating junction and storage temperature range TA= 25°C TA=100°C VRRM VRMS VDC I(AV) 50 35 50 100 70 100 200 140 200 400 280 400 1.0 600 420 600 800 560 800 1000 700 1000 Volts Volts Volts Amp IFSM VF IR(AV) 30.0 1.1 30.0 5.0 50.0 30.0 15.0 50.0 25.0 +150 -50 to +175 Amps Volts µA µA µs pF °C/W °C °C IR trr CJ RΘJA RΘJL TA TJ, TSTG NOTES: (1) Measured on Tektronix Type "S" recovery plug-in. Tektronix 545 Scope or equivalent, IFM=20mA, IRM=1mA (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient and from junction to lead at 0.375" (9.5mm) lead length, P.C.B. mounted *JEDEC registered value 4/98 RATINGS AND CHARACTERISTIC CURVES 1N4001 THRU 1N4007 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT FIG.1 - FORWARD CURRENT DERATING CURVE AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 30 PEAK FORWARD SURGE CURRENT, AMPERES 1.0 60 HZ RESISTIVE OR INDUCTIVE LOAD 8.3ms SINGLE HALF SINE WAVE (JEDEC Method) TA=75°C 0.8 0.2 x 0.2” (5.0 x 5.0mm) COPPER PADS 25 0.6 20 0.4 15 0.2 0.375” (9.5mm) LEAD LENGTH 10 0 5.0 0 25 50 75 100 125 150 175 1 10 NUMBER OF CYCLES AT 60 HZ 100 AMBIENT TEMPERATURE, °C FIG. 4 - TYPICAL REVERSE CHARACTERISTICS FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, MICROAMPERES 1,000 20 INSTANTANEOUS FORWARD CURRENT, AMPERES 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 100 TJ=150°C 1 10 TJ=100°C 0.1 1 0.1 TJ=25°C 0.01 0.6 0.8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 0.01 0 20 40 60 80 100 PERCENTAGE OF PEAK REVERSE VOLTAGE, % FIG. 5 - TYPICAL JUNCTION CAPACITANCE 100 TRANSIENT THERMAL IMPEDANCE, °C/W TJ=25°C f=1.0 MHz Vsig=50mVp-p FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE 100 JUNCTION CAPACITANCE, pF 10 10 1 1 0.1 1 10 100 0.1 0.01 0.1 1 t, PULSE DURATION, sec. 10 100 REVERSE VOLTAGE, VOLTS