1N4383GP

1N4383GP THRU 1N4385GP 1N4585GP AND 1N4586GP GLASS PASSIVATED JUNCTION RECTIFIER Reverse Voltage - 200 to 1000 Volts D * DO-204AC 0.034 (0.86) 1.0 (25.4) MIN. 0.028 (0.71) DIA. Forward Current - 1.0 Ampere FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High temperature metallurgically bonded construction ♦ Glass passivated cavity-free junction ♦ Capable of meeting environmental standards of MIL-S-19500 ♦1.0 Ampere operation at TA=100°C with no thermal runaway ♦ High temperature soldering guaranteed: 350°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension P A T E N T E 0.300 (7.6) 0.230 (5.8) 0.140 (3.6) 0.104 (2.6) DIA. 1.0 (25.4) MIN. Dimensions in inches and (millimeters) MECHANICAL DATA Case: JEDEC DO-204AC molded plastic over glass body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.015 ounce, 0.4 gram *Glass-plastic encapsulation technique is covered by Patent No. 3,996,602 and brazed lead assembly by Patent No. 3,930,306 ® MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS 1N 4383GP 1N 4384GP 1N 4385GP 1N 4585GP 1N 4586GP UNITS * Maximum repetitive peak reverse voltage * Maximum RMS voltage * Maximum DC blocking voltage * Maximum average forward rectified current 0.375" (9.5mm) lead length at TA=100°C * Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) at TA=100°C Maximum instantaneous forward voltage at 1.0A Maximum DC reverse current at rated DC blocking voltage * Typical reverse recovery time (NOTE 1) Maximum full load reverse current full cycle average at 0.375" (9.5mm) lead length at TA=100°C Typical junction capacitance (NOTE 2) Typical thermal resistance (NOTE 3) * Operating junction and storage temperature range TA=25°C TA=150°C VRRM VRMS VDC I(AV) 200 140 200 400 280 400 600 420 600 1.0 800 560 800 1000 700 1000 Volts Volts Volts Amp IFSM VF IR trr IR(AV) CJ RΘJA TJ, TSTG 275 250 50.0 1.0 5.0 250.0 2.0 225 15.0 45.0 -65 to +175 200 200 Amps Volts µA µs µA pF °C/W °C NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient at 0.375" (9.5mm) lead length, P.C.B. mounted * JEDEC registered values 4/98 RATINGS AND CHARACTERISTIC CURVES 1N4383GP THRU 1N4385GP, 1N4585GP AND 1N4586GP AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 1 - FORWARD CURRENT DERATING CURVE FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.375"(9.5mm) LEAD LENGTH PEAK FORWARD SURGE CURRENT, AMPERES 60 HZ RESISTIVE OR INDUCTIVE LOAD 50 40 30 TA=100°C 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 20 10 0 25 50 75 100 125 150 175 200 0 1 10 NUMBER OF CYCLES AT 60 HZ 100 AMBIENT TEMPERATURE, °C INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 20 INSTANTANEOUS FORWARD CURRENT, AMPERES 10 TJ=125°C 10 1 TJ=75°C TJ=25°C PULSE WIDTH=300µs 1 0.1 TJ=25°C 0.1 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 5 - TYPICAL JUNCTION CAPACITANCE TRANSIENT THERMAL IMPEDANCE (°C/W) 100 TJ=25°C f=1.0 MHZ Vsig=50mVp-p FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE 100 JUNCTION CAPACITANCE, pF 10 10 1 0.1 0.01 0.1 1 10 100 t, PULSE DURATION, sec 1 1 10 REVERSE VOLTAGE, VOLTS 100