1N5391

1N5391 THRU 1N5399 GENERAL PURPOSE PLASTIC RECTIFIER Reverse Voltage - 50 to 1000 Volts DO-204AL Forward Current - 1.5 Amperes FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High surge current capability ♦ 1.5 Ampere operation at TL=70°C with no thermal runaway ♦ Low reverse leakage ♦ Construction utilizes void-free molded plastic technique ♦ High temperature soldering guaranteed: 250°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension 1.0 (25.4) MIN. 0.107 (2.7) 0.080 (2.0) DIA. 0.205 (5.2) 0.160 (4.1) MECHANICAL DATA 1.0 (25.4) MIN. 0.034 (0.86) 0.028 (0.71) DIA. Case: JEDEC DO-204AL molded plastic body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.012 ounce, 0.3 gram Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS 1N 5391 1N 5392 1N 5393 1N 5394 1N 5395 1N 5396 1N 5397 1N 1N 5398 5399 UNITS *Maximum repetitive peak reverse voltage *Maximum RMS voltage *Maximum DC blocking voltage *Maximum average forward rectified current 0.500” (12.7mm) lead length at TL=70°C *Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) at TA=75°C *Maximum instantaneous forward voltage at 1.5A TA=70°C *Maximum DC reverse current at rated DC blocking voltage TA=25°C TA=150°C VRRM VRMS VDC I(AV) 50 35 50 100 70 100 200 140 200 300 210 300 400 280 400 1.5 500 350 500 600 420 600 800 1000 Volts 560 700 800 1000 Volts Volts Amps IFSM 50.0 Amps VF 1.4 5.0 300.0 300.0 2.0 15.0 50.0 25.0 +150 -50 to + 170 -50 to+175 Volts µA µA µs pF °C/W °C °C °C IR IR(AV) trr CJ RΘJA RΘJL TA TJ TSTG *Maximum full load reverse current full cycle average, 0.375",(9.5mm) lead length at TL=70°C Typical reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Typical thermal resistance (NOTE 3) *Maximum DC blocking voltage temperature *Operating junction temperature range *Storage temperature range NOTES: (1) Measured with IF=0.5A, IR=0.1A, Irr= 0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient and from junction to lead at 0.375” (9.5mm) lead length, P.C.B. mounted *JEDEC registered value 4/98 RATINGS AND CHARACTERISTIC CURVES 1N5391 THRU 1N5399 FIG. 1 - FORWARD CURRENT DERATING CURVE AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 2.4 2.0 1.6 1.2 0.8 0.4 50 PEAK FORWARD SURGE CURRENT, AMPERES 60 HZ RESISTIVE OR INDUCTIVE LOAD 0.50” (12.7mm) LEAD LENGTH 8.3ms SINGLE HALF SINE WAVE (JEDEC Method) TA=75°C 40 30 0.2 x 0.2” (5.0 x 5.0mm) COPPER PADS 10 Ipk/IAV = 20 CAPACITIVE LOADS 5 20 10 0 25 50 75 100 125 150 175 LEAD TEMPERATURE, °C 0 1 10 NUMBER OF CYCLES AT 60HZ 100 FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 100 INSTANTANEOUS FORWARD CURRENT, AMPERES INSTANTANEOUS REVERSE CURRENT, MICROAMPERES 1,000 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 100 TJ=150°C 10 1 1 0.1 0.1 TJ=25°C 0.01 0.6 0.8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 5 - TYPICAL JUNCTION CAPACITANCE 100 TRANSIENT THERMAL IMPEDANCE, °C/W TJ=25°C f=1.0 MHz Vsig=50mVp-p FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE 100 JUNCTION CAPACITANCE, pF 10 10 1 1 0.1 1 10 100 0.1 0.01 0.1 1 t, PULSE DURATION, sec. 10 100 REVERSE VOLTAGE, VOLTS