1N5398GP

1N5391GP THRU 1N5399GP GLASS PASSIVATED JUNCTION RECTIFIER Reverse Voltage - 50 to 1000 Volts * D DO-204AC 0.034 (0.86) 1.0 (25.4) MIN. 0.028 (0.71) DIA. Forward Current - 1.5 Amperes FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High temperature metallurgically bonded construction ♦ Glass passivated cavity-free junction ♦ Capable of meeting environmental standards of MIL-S-19500 ♦ 1.5 Ampere operation at TA=70°C with no thermal runaway ♦ Typical IR less than 0.1µA ♦ High temperature soldering guaranteed: 350°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension P A T E N T E 0.300 (7.6) 0.230 (5.8) 0.140 (3.6) 0.104 (2.6) DIA. 1.0 (25.4) MIN. Dimensions in inches and (millimeters) *Glass-plastic encapsulation technique is covered by Patent No. 3,996,602 and brazed-lead assembly by Patent No. 3,930,306 ® MECHANICAL DATA Case: JEDEC DO-204AC molded plastic over glass body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.015 ounce, 0.4 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS 1N53 91GP 1N53 92GP 1N53 93GP 1N53 94GP 1N53 95GP 1N53 96GP 1N53 97GP 1N53 98GP 1N53 99GP UNITS * Maximum repetitive peak reverse voltage * Maximum RMS voltage * Maximum DC blocking voltage * Maximum average forward rectified current 0.375" (9.5mm) lead length at TL=70°C * Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) * Maximum instantaneous forward voltage at 1.5A, TA=70°C *Maximum DC reverse current at rated DC blocking voltage * Maximum full load reverse current full cycle average, 0 375" (9.5mm) lead length at TA=70°C Typical reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Typical thermal resistance (NOTE 3) *Operating junction and storage temperature range TA=25°C TA=150°C VRRM VRMS VDC I(AV) 50 35 50 100 70 100 200 140 200 300 210 300 400 280 400 1.5 500 350 500 600 420 600 800 560 800 1000 700 1000 Volts Volts Volts Amps IFSM VF IR IR(AV) trr CJ RΘJA TJ, TSTG -65 50.0 1.4 5.0 300.0 300.0 2.0 15.0 45.0 to +175 Amps Volts µA µA µs pF °C/W °C NOTES: (1) Reverse recovery test condition: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient at 0.375" (9.5mm) lead length, P.C.B. mounted * JEDEC registered values 4/98 RATINGS AND CHARACTERISTIC CURVES 1N5391GP THRU 1N5399GP FIG. 1 - FORWARD CURRENT DERATING CURVE AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 2.0 PEAK FORWARD SURGE CURRENT, AMPERES TL, LEAD TEMPERATURE 60 HZ RESISTIVE OR INDUCTIVE LOAD TA, AMBIENT TEMPERATURE 50 40 TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 1.0 30 0.5 20 10 0.375" (9.5mm) LEAD LENGTH 0 0 25 50 75 100 125 150 175 0 1 10 NUMBER OF CYCLES AT 60 HZ TEMPERATURE, °C 100 FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, MICROAMPERES 10 INSTANTANEOUS FORWARD CURRENT, AMPERES 10 TJ=125°C 1 1 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE TJ=75°C 0.1 0.1 TJ=25°C 0.01 0 20 40 60 80 100 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 PERCENT OF RATED PEAK REVERSE VOLTAGE, % INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 5 - TYPICAL JUNCTION CAPACITANCE FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE (°C/W) 100 TJ=25°C f=1.0 MHZ Vsig=50mVp-p 100 JUNCTION CAPACITANCE, pF 10 10 1 0.1 0.01 0.1 1 10 100 t, PULSE DURATION, sec 1 1 10 REVERSE VOLTAGE, VOLTS 100