1N5401

1N5400 THRU 1N5408 GENERAL PURPOSE PLASTIC RECTIFIER Reverse Voltage - 50 to 1000 Volts DO-201AD Forward Current - 3.0 Amperes FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High surge current capability ♦ Construction utilizes void-free molded plastic technique ♦ 3.0 Ampere operation at TL=105°C with no thermal runaway ♦ Typical IR less than 0.1µA ♦ High temperature soldering guaranteed: 250°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension 1.0 (25.4) MIN. 0.210 (5.3) 0.190 (4.8) DIA. 0.375 (9.5) 0.285 (7.2) 0.052 (1.32) 0.048 (1.22) DIA. 1.0 (25.4) MIN. MECHANICAL DATA Case: JEDEC DO-201AD molded plastic body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.04 ounce, 1.1 grams Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS 1N 5400 1N 5401 1N 5402 1N 5403 1N 5404 1N 5405 1N 5406 1N 5407 1N 5408 UNITS *Maximum repetitive peak reverse voltage *Maximum RMS voltage *Maximum DC blocking voltage to TA=150°C *Maximum average forward rectified current 0.5” (12.5mm) lead length at TL=105°C *Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) at TL=105°C *Maximum instantaneous forward voltage at 3.0A *Maximum DC reverse current at rated DC blocking voltage TA=25°C TA=150°C VRRM VRMS VDC I(AV) 50 35 50 100 70 100 200 140 200 300 210 300 400 280 400 3.0 500 350 500 600 420 600 800 1000 Volts 560 700 Volts 800 1000 Volts Amps IFSM VF IR IR(AV) CJ RΘJA TA TJ TSTG 200.0 1.2 10.0 500.0 500.0 30.0 20.0 +150 -50 to +170 -50 to +170 Amps Volts µA µA pF °C/W °C °C °C *Maximum full load reverse current full cycle average, 0.5" (12.5mm) lead length at TL=105°C Typical junction capacitance (NOTE 1) *Typical thermal resistance (NOTE 2) Maximum DC blocking voltage temperature *Operating junction temperature range *Storage temperature range NOTES: (1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (2) Thermal resistance from junction to ambient at 0.375” (9.5mm) lead length, P.C.B. mounted with 0.8 x 0.8” (20 x 20mm) copper heatsinks *JEDEC registered value 4/98 RATINGS AND CHARACTERISTIC CURVES 1N5400 THRU 1N5408 FIG.1 - FORWARD CURRENT DERATING CURVE AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 8.0 7.0 6.0 5.0 4.0 L=0.50” (12.7 mm) L=0.31” (0.79mm) L=0.25” (6.3 mm) TL=LEAD TEMPERATURE with BOTH LEADS HEAT SINK MOUNTED with LENGTH (L) AS SHOWN 60 Hz RESISTIVE OR INDUCTIVE LOAD FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT INSTANTANEOUS FORWARD CURRENT, AMPERES 400 8.3ms SINGLE HALF SINE WAVE (JEDEC Method) TL=105°C 1.0 CYCLE 3.0 2.0 1.0 0 40 TA=AMBIENT TEMPERATURE 0.375” (9.5mm) LEAD LENGTH P.C. B. MOUNTING 100 60 80 100 120 140 160 180 40 1.0 10 NUMBER OF CYCLES AT 60 HZ 100 TEMPERATURE, °C FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 100 100 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 10 TJ=150°C 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 1 TJ=100°C 1 0.1 0.1 TJ=25°C 0.01 0 20 40 60 80 100 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 PERCENT OF RATED PEAK REVERSE VOLTAGE,% INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE FIG. 5 - TYPICAL JUNCTION CAPACITANCE 100 70 JUNCTION CAPACITANCE, pF TJ=25°C f=1.0 MHz Vsig=50mVp-p TRANSIENT THERMAL IMPEDANCE, °C/W 100 10 10 1 1 0.1 1 10 100 0.1 0.01 0.1 1 t, PULSE DURATION, sec. 10 100 REVERSE VOLTAGE, VOLTS