1N5623

1N5615 THRU 1N5623 GLASS PASSIVATED FAST SWITCHING RECTIFIER Reverse Voltage - 200 to 1000 Volts DO-204AP Forward Current - 1.0 Ampere FEATURES 0.034 (0.86) 0.028 (0.71) DIA. 1.0 (25.4) MIN. 0.240 (6.1) MAX. 0.150 (3.8) 0.100 (2.5) DIA. ♦ High temperature metallurgically bonded construction ♦ Hermetically sealed case ♦ Glass passivated cavity-free junction ♦ 1.0 Ampere operation at TA=55°C with no thermal runaway ♦ Typical IR less than 0.1µA ♦ Capable of meeting environmental standards of MIL-S-19500 ♦ Fast switching for high efficiency ♦ High temperature soldering guaranteed: 350°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension P A T E N T E D * 1.0 (25.4) MIN. MECHANICAL DATA Case: JEDEC DO-204AP Solid glass body Terminals: Solder plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.02 ounce, 0.56 gram Dimensions in inches and (millimeters) *Brazed-lead assembly is covered by Patent No. 3,930,306 MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS 1N5615 1N5617 1N5619 1N5621 1N5623 UNITS *Maximum repetitive peak reverse voltage Maximum RMS voltage *Maximum DC blocking voltage *Minimum reverse breakdown voltage at 50 µA *Maximum average forward rectified current 0.375” (9.5mm) lead length at T A=55°C *Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) *Maximum instantaneous forward voltage at 1.0A *Maximum DC reverse current at rated DC blocking voltage TA=25°C TA=100°C TA=200°C VRRM VRMS VDC V(BR) I(AV) 200 140 200 220 400 280 400 440 600 420 600 660 1.0 800 560 800 880 1000 700 1000 1100 Volts Volts Volts Volts Amp IFSM VF IR trr CJ RΘJA TJ TSTG 150 45 150 35 50.0 1.2 0.5 25.0 1500.0 250 25 55.0 -65 to +175 -65 to +200 300 20 500 15 Amps Volts µA ns pF °C/W °C °C *Maximum reverse recovery time (NOTE 1) *Maximum junction capacitance (NOTE 2) Typical thermal resistance (NOTE 3) *Operating junction temperature range *Storage temperature range NOTES: (1) Reverse recovery test conditions IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHZ and applied reverse voltage of 12 Volts (3) Thermal resistance from junction to ambient at 0.375” (9.5mm) lead length, P.C.B.mounted *JEDEC registered values 4/98 RATINGS AND CHARACTERISTIC CURVES 1N5615 THRU 1N5623 AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 1 - FORWARD CURRENT DERATING CURVE INSTANTANEOUS SURGE CURRENT, AMPERES FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 1.0 50 0.75 RESISTIVE OR INDUCTIVE LOAD 0.375" (9.5mm) LEAD LENGTH 40 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) TJ=TJ max. 0.5 30 20 0.25 10 0 25 50 75 100 125 150 175 AMBIENT TEMPERATURE, °C 0 1 10 NUMBER OF CYCLES AT 60 HZ 100 FIG. 3 -TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 10.0 INSTANTANEOUS FORWARD CURRENT, AMPERES FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 20 10 1 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE INSTANTANEOUS REVERSE CURRENT, MICROAMPERES TJ=125°C 0.1 1 TJ=75°C 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 0.1 INSTANTANEOUS FORWARD VOLTAGE, VOLTS TJ=25°C FIG. 5 - TYPICAL JUNCTION CAPACITANCE 30 JUNCTION CAPACITANCE, pF 0.01 TJ=25°C f=1.0 MHZ Vsig=50m Vp-p 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 10 1 1 10 REVERSE VOLTAGE, VOLTS 100