3N251

KBP005M THRU KBP10M 3N246 THRU 3N252 GLASS PASSIVATED SINGLE-PHASE RECTIFIER BRIDGE Reverse Voltage - 50 to 1000 Volts Case Style KBPM 0.600 (15.24) 0.125 x 45o (3.2) 0.560 (14.22) Forward Current - 1.5 Amperes FEATURES 0.460 (11.68) 0.420 (10.67) 0.500 (12.70) 0.460 (11.68) 60 (15.2) MIN. 0.060 (1.52) 0.160 (4.1) 0.140 (3.6) 0.50 (12.7) MIN. ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ This series is UL listed under Recognized Component Index, file number E54214 ♦ Glass passivated chip junctions ♦ High surge current capability ♦ Ideal for printed circuit board ♦ High temperature soldering guaranteed: 260°C/10 seconds at 5 lbs. (2.3kg) tension 0.034 (8.6) 0.028 (7.6) DIA. MECHANICAL DATA 0.105 (2.67) 0.085 (2.16) 0.200 (5.08) 0.180 (4.57) Polarity shown on front side of case: positive lead by beveled corner Case: Molded plastic body over passivated junctions Terminals: Plated lead solderable per MIL-STD-750, Method 2026 Polarity: Polarity symbols marked on case Mounting position: Any Weight: 0.06 ounce, 1.7 grams Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. KBP KBP 005M 01M SYMBOLS 3N246 3N247 KBP 02M 3N248 KBP 04M 3N249 KBP 06M 3N250 KBP 08M 3N251 KBP 10M 3N252 UNITS * Maximum repetitive peak reverse voltage * Maximum RMS voltage * Maximum DC blocking voltage Maximum average forward output rectified current at TA=40°C * Peak forward surge current single half sine-wave superimposed on rated load (JEDEC Method) Rating for fusing (t < 8.3ms) * Maximum instantaneous forward voltage drop * Maximum DC reverse current at rated DC blocking voltage per leg Typical junction capacitance per leg (NOTE 1) Typical thermal resistance per leg (NOTE 2) * Operating junction and storage temperature range at 1.0A per leg 1.57A per leg TA=25°C TA=125°C TJ=150°C VRRM VRMS VDC I(AV) IFSM I2t VF IR CJ RΘJA RΘJL TJ, TSTG 50 35 50 100 70 100 200 140 200 400 280 400 1.5 50.0 30.0 10.0 1.0 1.3 5.0 500.0 15.0 40.0 13.0 600 420 600 800 560 800 1000 700 1000 Volts Volts Volts Amps Amps A2sec Volts µA pF °C/W °C -55 to +150 NOTES: (1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (2) Thermal resistance from junction to ambient and from junction to lead mounted on P.C.B. with, 0.47 x 0.47" (12 x12mm) copper pads * JEDEC registered values 4/98 RATINGS AND CHARACTERISTICS CURVES KBP005M THRU KBP10M / 3N246 THRU 3N252 FIG.1 - DERATING CURVE OUTPUT RECTIFIED CURRENT PEAK FORWARD SURGE CURRENT, AMPERES BRIDGE OUTPUT FULL WAVE RECTIFIED CURRENT, AVERAGE AMPERES FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 20 CAPACITIVE LOAD Ipk/IAV=5.0 Ipk/IAV=10 Ipk/IAV=20 (PER LEG) 60 Hz RESISTIVE OR INDUCTIVE LOAD P.C.B. MOUNTED WITH 0.47 x 0.47” (12 x 12mm) COPPER PADS 60 50 40 TA=25°C 30 20 10 1.0 CYCLE TJ=150°C SINGLE SINE-WAVE (JEDEC Method) 0 40 60 80 100 120 140 150 1 10 NUMBER OF CYCLES AT 60 HZ 100 AMBIENT TEMPERATURE, °C FIG. 3 - TYPICAL FORWARD CHARACTERISTICS PER LEG TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE FIG. 4 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG 10 INSTANTANEOUS FORWARD CURRENT, AMPERES INSTANTANEOUS REVERSE CURRENT, MICROAMPERES 20 10 TJ=125°C 1 TJ=100°C 1 0.1 TJ=25°C 0.1 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG 100 JUNCTION CAPACITANCE, pF TJ=25°C f=1.0 MHz Vsig=50mVp-p 10 1 0.1 1 10 100 REVERSE VOLTAGE, VOLTS