BYV32-100

BYV32-50 THRU BYV32-200 FAST EFFICIENT PLASTIC RECTIFIER Reverse Voltage - 50 to 150 Volts TO-220AB 0.415 (10.54) MAX. 0.370 (9.40) 0.360 (9.14) 0.154 (3.91) 0.185 (4.70) 0.175 (4.44) DIA. 0.148 (3.74) 0.055 (1.39) 0.045 (1.14) Forward Current - 18.0 Amperes FEATURES ♦ Dual rectifier construction, positive centertap ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ Glass passivated chip junctions ♦ Low power loss ♦ Low forward voltage, high current capability ♦ High surge capability ♦ Superfast recovery time for high efficiency ♦ High temperature soldering guaranteed: 250°C, 0.16" (4.06mm) from case for 10 seconds 0.113 (2.87) 0.103 (2.62) 0.145 (3.68) 0.135 (3.43) 0.560 (14.22) 0.530 (13.46) 0.410 (10.41) 0.390 (9.91) PIN 2 0.635 (16.13) 0.625 (15.87) 1 0.160 (4.06) 0.140 (3.56) 0.560 (14.22) 0.530 (13.46) 3 0.350 (8.89) 0.330 (8.38) 1.148 (29.16) 1.118 (28.40) 0.110 (2.79) 0.100 (2.54) MECHANICAL DATA 0.105 (2.67) 0.095 (2.41) 0.037 (0.94) 0.027 (0.68) 0.105 (2.67) 0.095 (2.41) 0.205 (5.20) 0.195 (4.95) 0.022 (0.56) 0.014 (0.35) PIN 1 PIN 3 PIN 2 CASE Dimensions in inches and (millimeters) Case: JEDEC TO-220AB molded plastic body over passivated chips Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Weight: 0.08 ounce, 2.24 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS BYV32-50 BYV32-100 BYV32-150 BYV32-200 UNITS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TC=120°C Peak forward surge current 10ms single half sine-wave superimposed at at TJ=150°C Maximum instantaneous forward voltage per leg at: IF=20A IF=5.0A, TJ=100°C Maximum DC reverse current at rated DC blocking voltage TC=25°C TC=100°C VRRM VRMS VDC I(AV) 50 35 50 100 70 100 18.0 150 105 150 200 140 200 Volts Volts Volts Amps IFSM 150.0 Amps VF 1.15 0.85 10.0 600.0 25.0 45.0 20.0 3.0 -65 to +150 Volts µA ns pF °C/W °C IR trr CJ RΘJA RΘJC TJ, TSTG Maximum reverse recovery time per leg (NOTE 1) Typical junction capacitance per leg (NOTE 2) Maximum thermal resistance per leg (NOTE 3) Operating and storage temperature range NOTES: (1) Reverse recovery test conditions: IF=1A VR=30V, di/dt=100A/µs, Irr=10% IRM (2) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient and from junction to case per leg mounted on heatsink 4/98 RATINGS AND CHARACTERISTIC CURVES BYV32-50 THRU BYV32-200 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG PEAK FORWARD SURGE CURRENT, AMPERES FIG.1 - FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT, AMPERES 20 18 16 12 8.0 4.0 0 RESISTIVE OR INDUCTIVE LOAD 150 125 100 75 50 25 0 TJ=150°C 10ms SINGLE HALF SINE WAVE (JEDEC Method) 0 50 100 150 CASE TEMPERATURE, °C 1 10 NUMBER OF CYCLES AT 50 HZ 100 FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG FIG. 4 - TYPICAL REVERSE CHARACTERISTICS PER LEG 100 1,000 INSTANTANEOUS FORWARD CURRENT, AMPERES 10 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES TJ = 25°C PULSE WIDTH = 300µs 1% DUTY CYCLE 100 TC=100°C 1 10 0.1 0.01 0.4 1 0.6 0.8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, VOLTS TC=25°C 0.1 FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 60 JUNCTION CAPACITANCE, pF 50 40 30 20 10 0 TJ=25°C f=1.0 MHZ Vsig=5mVp-p 1 10 REVERSE VOLTAGE, VOLTS 100