BYVB32-50

NEW PRODUCT NEW PRODUCT NEW PRODUCT BYVB32-50 THRU BYVB32-200 FAST EFFICIENT PLASTIC RECTIFIER Reverse Voltage - 50 to 150 Volts TO-263AB 0.380 (9.65) 0.420 (10.67) 0.245 (6.22) MIN K 0.047 (1.19) 0.055 (1.40) 0.160 (4.06) 0.190 (4.83) 0.045 (1.14) 0.055 (1.40) Forward Current - 18.0 Amperes FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ Dual rectifier construction, positive centertap ♦ Glass passivated chip junctions ♦ Low power loss ♦ Low forward voltage, high current capability ♦ High surge capability ♦ Superfast recovery time for high efficiency ♦ High temperature soldering in accordance with CECC 802 / Reflow guaranteed 0.320 (8.13) 0.360 (9.14) 1 K 2 0.575 (14.60) 0.625 (15.88) SEATING PLATE -T- 0.090 (2.29) 0.110 (2.79) 0.018 (0.46) 0.025 (0.64) 0.027 (0.686) 0.037 (0.940) 0.080 (2.03) 0.110 (2.79) 0.095 (2.41) 0.100 (2.54) MECHANICAL DATA Case: JEDEC TO-263AB molded plastic body Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Weight: 0.08 ounce, 2.24 grams PIN 1 K - HEATSINK PIN 2 Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS BYVB32-50 BYVB32-100 BYVB32-150 BYVB32-200 UNITS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TC=120°C Peak forward surge current 10ms single half sine-wave superimposed at at TJ=150°C Maximum instantaneous forward voltage per leg at: IF=20A, IF=5.0A, TJ=100°C Maximum DC reverse current at rated DC blocking voltage Typical junction capacitance (NOTE 2) Maximum thermal resistance per leg (NOTE 3) Operating and storage temperature range TJ=25°C TJ=100°C VRRM VRMS VDC I(AV) 50 35 50 100 70 100 18.0 150 105 150 200 140 200 Volts Volts Volts Amps IFSM 150.0 Amps VF 1.15 0.85 10.0 600.0 35.0 45.0 3.0 -65 to +150 Volts µA ns pF °C/W °C IR trr CJ RΘJC TJ, TSTG Maximum reverse recovery time per leg (NOTE 1) NOTES: (1) Reverse recovery test conditions: IF=1A VR=30V, di/dt=100A/µs, Irr=10% IRM (2) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to case per leg mounted on heatsink NOTICE: Advanced product information is subject to change without notice 4/98 RATINGS AND CHARACTERISTIC CURVES BYVB32-50 THRU BYVB32-200 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG PEAK FORWARD SURGE CURRENT, AMPERES FIG.1 - FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT, AMPERES 20 18 16 12 8.0 4.0 0 150 125 100 75 50 25 0 TJ=150°C 10ms SINGLE HALF SINE WAVE (JEDEC Method) RESISTIVE OR INDUCTIVE LOAD 0 50 100 150 1 10 NUMBER OF CYCLES AT 50 HZ 100 CASE TEMPERATURE, °C FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG FIG. 4 - TYPICAL REVERSE CHARACTERISTICS PER LEG 100 1,000 INSTANTANEOUS FORWARD CURRENT, AMPERES 10 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES TJ = 25°C PULSE WIDTH = 300µs 1% DUTY CYCLE 100 TC=100°C 1 10 0.1 0.01 0.4 1 0.6 0.8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, VOLTS TC=25°C 0.1 FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG 0 20 40 60 80 100 60 JUNCTION CAPACITANCE, pF PERCENT OF RATED PEAK REVERSE VOLTAGE, % 50 40 30 20 10 0 TJ=25°C f=1.0 MHZ Vsig=5mVp-p 1 10 REVERSE VOLTAGE, VOLTS 100