BYW29-200

BYW29-50 THRU BYW29-200 FAST EFFICIENT PLASTIC RECTIFIER Reverse Voltage - 50 to 200 Volts TO-220AC 0.185 (4.70) 0.415 (10.54) MAX. 0.370 (9.40) 0.360 (9.14) 0.154 (3.91) DIA. 0.148 (3.74) 0.055 (1.39) 0.045 (1.14) 0.175 (4.44) Forward Current - 8.0 Amperes FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ Glass passivated chip junction ♦ Low power loss ♦ Low leakage current ♦ High surge current capability ♦ Superfast recovery time for high efficiency ♦ High temperature soldering guaranteed: 250°C, 0.16” (4.06mm) from case for 10 seconds 0.113 (2.87) 0.103 (2.62) 0.145 (3.68) 0.135 (3.43) 0.560 (14 0.530 (13. 0.410 (10.41) 0.390 (9.91) PIN 1 0.160 (4.06) 0.140 (3.56) 0.560 (14.22) 0.530 (13.46) 2 0.635 (16.13) 0.625 (15.87) 0.350 (8.89) 0.330 (8.38) 1.148 (29.16) 1.118 (28.40) 0.110 (2.79) 0.100 (2.54) MECHANICAL DATA Case: JEDEC TO-220AC molded plastic body over passivated chip Terminals: Plated lead solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Weight: 0.064 ounce, 1.81 grams 0.105 (2.67) 0.095 (2.41) 0.037 (0.94) 0.027 (0.68) 0.022 (0.56) 0.014 (0.36) PIN 1 0.205 (5.20) 0.195 (4.95) PIN 2 CASE Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS BYW29-50 BYW29-100 BYW29-150 BYW29-200 UNITS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TC=125°C Peak forward surge current 10ms single half sine-wave superimposed at TJ=150°C Maximum instantaneous forward voltage at:IF=20A, TJ=25°C IF=8A, TJ=150°C Maximum DC reverse current at rated DC blocking voltage Maximum reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Maximum thermal resistance (NOTE 3) (NOTE 4) VRRM VRMS VDC I(AV) IFSM VF IR trr CJ RΘJA RΘJC TJ, TSTG 50 35 50 100 70 100 8.0 100.0 1.3 0.8 150 105 150 200 140 200 Volts Volts Volts Amps Amps Volts µA ns pF °C/W °C TC=25°C TC=100°C 10.0 500.0 25.0 45.0 20.0 3.0 -65 to +150 Operating and storage temperature range NOTES: (1) Reverse recovery test conditions: IF=1A, VR=30V, di/dt=100A/µs, Irr=10%, IRM for measurement of trr (2) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient in free air; no heatsink (4) Thermal resistance from junction to case mounted on heatsink 4/98 RATINGS AND CHARACTERISTIC CURVES BYW29-50 THRU BYW29-200 FIG. 1 - MAXIMUM FORWARD CURRENT DERATING CURVE AVERAGE FORWARD RECTIFIED CURRENT, AMPERES RESISTIVE OR INDUCTIVE LOAD FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, AMPERES 10 8.0 6.0 4.0 2.0 0 100 80 60 40 20 0 TJ=TJ max. 10ms SINGLE HALF SINE-WAVE (JEDEC Method) 0 50 100 150 1 10 NUMBER OF CYCLES AT 50 HZ 100 CASE TEMPERATURE, °C FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS 80 100 INSTANTANEOUS FORWARD CURRENT, AMPERES TJ=25°C 10 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES TJ=125°C PULSE WIDTH=300µs 1% DUTY CYCLE 10 TJ=100°C 1 1 0.1 0.1 0.01 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 INSTANTANEOUS FORWARD VOLTAGE, VOLTS TJ=25°C 0.01 FIG. 5 - TYPICAL JUNCTION CAPACITANCE 0 20 40 60 80 100 80 JUNCTION CAPACITANCE, pF PERCENT OF RATED PEAK REVERSE VOLTAGE, % 70 60 50 40 30 20 0.1 TJ=25°C f=1.0 MHZ Vsig=50mVp-p 1 10 100 REVERSE VOLTAGE, VOLTS