FEP16HT

FEP16AT THRU FEP16JT FAST EFFICIENT PLASTIC RECTIFIER Reverse Voltage - 50 to 600 Volts TO-220AB 0.185 (4.70) 0.175 (4.44) 0.154 (3.91) DIA. 0.148 (3.74) 0.055 (1.39) 0.045 (1.14) Forward Current - 16.0 Amperes FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ Dual rectifier construction, positive centertap ♦ Glass passivated chip junctions ♦ Low power loss ♦ Low forward voltage, high current capability ♦ High surge current capability ♦ Superfast recovery times for high efficiency ♦ High temperature soldering guaranteed: 250°C, 0.16" (4.06mm) from case for 10 seconds 0.415 (10.54) MAX. 0.370 (9.40) 0.360 (9.14) 0.113 (2.87) 0.103 (2.62) 0.145 (3.68) 0.135 (3.43) 0.560 (14.22) 0.530 (13.46) 0.410 (10.41) 0.390 (9.91) PIN 2 0.635 (16.13) 0.625 (15.87) 1 0.160 (4.06) 0.140 (3.56) 0.560 (14.22) 0.530 (13.46) 3 0.350 (8.89) 0.330 (8.38) 1.148 (29.16) 1.118 (28.40) 0.110 (2.79) 0.100 (2.54) MECHANICAL DATA Case: JEDEC TO-220AB molded plastic body over passivated chips Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Mounting Torque: 5 in. - lbs. max. Weight: 0.08 ounce, 2.24 grams 0.105 (2.67) 0.095 (2.41) 0.037 (0.94) 0.027 (0.68) 0.105 (2.67) 0.095 (2.41) 0.205 (5.20) 0.195 (4.95) 0.022 (0.56) 0.014 (0.35) PIN 1 PIN 3 PIN 2 CASE Dimensions are in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. FEP SYMBOLS 16AT FEP 16BT FEP 16CT FEP 16DT FEP 16FT FEP 16GT FEP 16HT FEP 16JT UNITS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TC=100°C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage per leg at 8.0A Maximum DC reverse current at rated DC blocking voltage per leg Maximum reverse recovery time (NOTE 1) per leg Typical Junction Capacitance per leg (NOTE 2) Typical thermal resistance (NOTE 3) Operating junction and storage temperature range TC=25°C TC=100°C VRRM VRMS VDC I(AV) 50 35 50 100 70 100 150 105 150 200 140 200 300 210 300 400 280 400 500 350 500 600 420 600 Volts Volts Volts Amps 16.0 IFSM 200.0 Amps VF IR trr CJ RΘJA RΘJC TJ, TSTG 0.95 10.0 500.0 35.0 85.0 15.0 2.2 1.3 1.5 Volts µA 50.0 60.0 ns pF °C/W °C -55 to +150 NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient and from junction to case per leg mounted on heatsink 4/98 RATINGS AND CHARACTERISTICS CURVES FEP16AT THRU FEP16JT FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT FIG. 1 - FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT, AMPERES 20 16 12 8.0 4.0 0 PEAK FORWARD SURGE CURRENT, AMPERES RESISTIVE OR INDUCTIVE LOAD 300 250 200 150 100 50 0 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 0 50 100 150 CASE TEMPERATURE, °C 1 10 NUMBER OF CYCLES AT 60 HZ 100 FIG. 3- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG INSTANTANEOUS FORWARD CURRENT, AMPERES FIG. 4 -TYPICAL REVERSE CHARACTERISTICS PER LEG 40 100 50-400V 500-600V 10 TJ=125°C INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES 10 PULSE WIDTH=300µs 1% DUTY CYCLE 12 TJ= 5°C 1 TJ=25°C 50-400V 300-400V 500-600V TJ=1 00°C 1 0.1 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 0.1 TJ=25°C 0.01 0 FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 1,000 JUNCTION CAPACITANCE, pF TJ=125°C f=1.0 MHZ Vsig=50mVp-p 100 50-400V 500-600V 10 0.1 1 10 100 REVERSE VOLTAGE, VOLTS