FEPF6DT

NEW PRODUCT NEW PRODUCT NEW PRODUCT FEPF6AT THRU FEPF6DT FAST EFFICIENT PLASTIC RECTIFIER Reverse Voltage - 50 to 200 Volts ITO-220AB Forward Current - 6.0 Amperes FEATURES ♦ Plastic package has carries Underwriters Laboratory Flammability Classification 94V-0 ♦ Dual rectifier construction, positive center-tap ♦ Glass passivated chip junctions ♦ Superfast recovery times for high efficiency ♦ Low power loss ♦ Low forward voltage, high current capability ♦ For use in low voltage, high frequency inverters, free wheeling and polarity protection applications ♦ High temperature soldering guaranteed: 250°C, 0.25" (6.35mm) from case for 10 seconds 0.405 (10.27) 0.383 (9.72) 0.188 (4.77) 0.172 (4.36) 0.110 (2.80) 0.100 (2.54) 0.140 (3.56) DIA. 0.130 (3.30) 0.131 (3.39) DIA. 0.122 (3.08) 0.600 (15.5) 0.580 (14.5) PIN 1 2 3 0.670 (17.2) 0.646 (16.4) 0.350 (8.89) 0.330 (8.38) 0.191 (4.85) 0.171 (4.35) 0.560 (14.22) 0.530 (13.46) 0.060 (1.52) 0.110 (2.80) 0.100 (2.54) MECHANICAL DATA 0.037 (0.94) 0.027 (0.69) 0.105 (2.67) 0.095 (2.41) 0.022 (0.55) 0.014 (0.36) PIN 1 PIN 3 PIN 2 0.205 (5.20) 0.195 (4.95) Dimensions in inches and (millimeters) Case: JEDEC ITO-220AB molded plastic body over passivated chips Terminals: Plated lead solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Weight: 0.08 ounce, 2.24 grams Mounting Torque: 5 in. - lb. max. MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS FEPF6AT FEPF6BT FEPF6CT FEPF6DT UNITS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current TC=100°C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage per leg at 3.0A Maximum DC reverse current at rated DC blocking voltage Typical thermal resistance (NOTE 2) Typical junction capacitance per leg (NOTE 3) Operating junction and storage temperature range TA=25°C TA=100°C VRRM VRMS VDC I(AV) 50 35 50 100 70 100 6.0 150 105 150 200 140 200 Volts Volts Volts Amps IFSM 100.0 Amps VF IR trr RΘJC CJ TJ, TSTG 0.975 5.0 50.0 35.0 5.4 28.0 -55 to +150 Volts µA ns °C/W pF °C Maximum reverse recovery time per leg (NOTE 1) NOTES: (1) Reverse recovery test conditions: IF=0.5A, Ir=1.0A, Irr=0.25A (2) Thermal resistance from junction to case per leg mounted on heatsink (3) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts 4/98 RATINGS AND CHARACTERISTICS CURVES FEPF6AT THRU FEPF6DT FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT FIG. 1 - FORWARD CURRENT DERATING CURVE 10 AVERAGE FORWARD CURRENT, AMPERES RESISTIVE OR INDUCTIVE LOAD 150 PEAK FORWARD SURGE CURRENT, AMPERES 8.0 6.0 4.0 2.0 0 0 50 100 150 CASE TEMPERATURE, °C 125 100 75 50 25 0 TC=100°C 8.3ms SINGLE HALF SINE WAVE (JEDEC Method) 1 10 NUMBER OF CYCLES AT 60 HZ 100 FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 40 INSTANTANEOUS FORWARD CURRENT, AMPERES TJ=125°C FIG. 4 - TYPICAL REVERSE CHARACTERISTICS PER LEG 100 10 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES 10 TJ=125°C TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 1 TJ=100°C 1 0.1 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 0.1 TJ=25°C FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG 0.01 0 20 40 60 80 100 60 JUNCTION CAPACITANCE, pF 50 40 30 20 10 0 0.1 TJ=25°C f=1.0 MHZ Vsig=50mVp-p PERCENT OF RATED PEAK REVERSE VOLTAGE, % 1 10 100 REVERSE VOLTAGE, VOLTS