GBPC2510

GBPC12, 15, 25 AND 35 SERIES GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER Reverse Voltage - 50 to 1000 Volts Current Voltage - 12.0 to 35.0 Amperes GBPC - W Wire leads GBPC - Standard ♦ The plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ This series is UL recognized under component index, file number E54214 ♦ Integrally molded heatsink provides very low thermal resistance for maximum heat dissipation ♦ Universal 3-way terminals; snap-on, wire wrap-around, or P.C.B. mounting ♦ High forward surge current capabilities ♦ Glass passivated chip junctions ♦ Typical IR less than 0.3µA ♦ High temperature soldering guaranteed: 260°C/10 seconds at 5lbs. (2.3 kg) tension FEATURES MECHANICAL DATA Case: Molded plastic with heatsink integrally mounted in the bridge encapsulation Terminals: Either plated 0.25" (6.35mm). Faston lugs or plated copper leads 0.040" (1.02mm) diameter. Suffix letter "W" added to indicate leads (e.g. GBPC12005W). Mounting Position: See NOTE 3 Polarity: Polarity symbols molded on body Mounting Torque: 20 in. - lb. max. Weight: 0.53 ounce, 15 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS 005 01 GBPC12, 15, 25, 35 02 04 06 08 10 UNITS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified output current (SEE FIG.1) VRRM VRMS VDC 50 35 50 100 70 100 200 140 200 400 280 400 12.0 15.0 25.0 35.0 200.0 300.0 300.0 400.0 160.0 375.0 375.0 660.0 1.1 600 420 600 800 560 800 1000 700 1000 Volts Volts Volts Amps GBPC12 GBPC15 GBPC25 GBPC35 GBPC12 GBPC15 GBPC25 GBPC35 GBPC12 GBPC15 GBPC25 GBPC35 GBPC12 GBPC15 GBPC25 GBPC35 IF=6.0A IF=7.5A IF=12.5A IF=17.5A TA=25°C TA=125°C I(AV) Peak forward surge current single sine-wave superimposed on rated load (JEDEC Method) Rating (non-repetitive, for t greater than 1ms and less than 8.3ms) for fusing Maximum instantaneous forward voltage drop per leg at IFSM Amps I2t A2 sec VF Volts Maximum reverse DC current at rated DC blocking voltage per leg RMS isolation voltage from case to leads Typical junction capacitance per leg (NOTE 1) IR VISO CJ RΘJC TJ, TSTG 5.0 500.0 2500.0 300.0 1.9 1.4 -55 to +150 µA Volts pF °C/W °C Typical thermal resistance per leg (NOTE 2) GBPC12-25 GBPC35 Operating junction storage temperature range NOTES: (1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (2) Thermal resistance from junction to case per leg (3) Bolt down on heat-sink with silicone thermal compound between bridge and mounting surface for maximum heat transfer efficiency with #10 screw 7/28/98 RATINGS AND CHARACTERISTICS CURVES GBPC12, 15, 25 AND 35 SERIES FIG. 1 - MAXIMUM OUTPUT RECTIFIED CURRENT 40 GBPC35 FIG. 2 - MAXIMUM OUTPUT RECTIFIED CURRENT BRIDGES MOUNTED on 9 x 3.5 x 4.6” (22.9 x 8.9 x 11.7cm) AL. FINNED PLATE 5 x 6 x 4.9” AL. FINNED PLATE 5 x 4 x 3” AL. FINNED PLATE 40 RthS-A=0.5 °C/W 35 AVERAGE FORWARD CURRENT, AMPERES 30 GBPC25 AVERAGE FORWARD CURRENT, AMPERES 35 30 25 20 15 10 5 0 0 GBPC35 GBPC25 RthS-A=0.5 °C/W 60 HZ RESISTIVE OR INDUCTIVE LOAD 25 20 GBPC15 GBPC15 RthS-A=1.0 °C/W 15 GBPC12 10 5 0 60 Hz RESISTIVE OR INDUCTIVE LOAD 6.0 x 2.2 x 2.2” AL. FINNED PLATE GBPC12 RthS-A=1.0 °C/W 0 25 50 75 100 125 150 175 200 10 20 30 40 50 60 70 80 90 100 AMBIENT TEMPERATURE, °C CASE TEMPERATURE, °C FIG. 3 - MAXIMUM POWER DISSIPATION FIG. 4 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 80 CAPACITIVE LOAD 500 PEAK FORWARD SURGE CURRENT, AMPERES TJ=TJ max. 0.5Single Sine-Wave (JEDEC Method) GBPC35 GBPC15 GBPC25 AVERAGE POWER DISSIPATION OF BRIDGE, WATTS 70 60 50 40 30 20 10 0 TJ=TJ max. 100 RESISTIVE OR INDUCTIVE LOAD GBPC12 1.0 CYCLE 1 10 NUMBER OF CYCLES AT 60Hz 100 0 10 20 30 40 AVERAGE OUTPUT CURRENT, AMPERES RATINGS AND CHARACTERISTICS CURVES GBPC12, 15, 25 AND 35 SERIES FIG. 6 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG FIG. 5 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 100 INSTANTANEOUS FORWARD CURRENT, AMPERES TJ=125°C 100 TJ=150°C 10 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES 50-400V 600-1000V 10 1 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 0.1 1 0.01 0.4 0.6 0.8 1 1.2 1.4 1.6 0.1 TJ=25°C INSTANTANEOUS FORWARD VOLTAGE, VOLTS 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 7 - TYPICAL JUNCTION CAPACITANCE PER LEG 600 TRANSIENT THERMAL IMPEDANCE, °C/W TJ=25°C f=1.0 MHz Vsig=50mVp-p FIG. 8 - TYPICAL TRANSIENT THERMAL IMPEDANCE PER LEG 100 JUNCTION, CAPACITANCE, pF TJ=25°C f=1.0 MHz Vsig=50mVp-p 10 100 1 50 1 10 REVERSE VOLTAGE, VOLTS 100 0.1 0.01 0.1 1 t, HEATING TIME, sec. 10 100 FIG. 9 Hole for #10 Screw 0.220 (5.59) DIA. 0.200 (5.08) GBPC 1.135 (28.8) 1.115 (28.3) 0.672 (17.1) 0.632 (16.1) AC 1.135 (28.8) 1.115 (28.3) 0.672 (17.1) 0.632 (16.1) 0.582 (14.8) 0.542 (13.8) 0.732 (18.6) 0.692 (17.6) 0.094 (2.4) DIA. 0.034 (0.86) 0.030 (0.76) 0.25 (6.35) 0.840 (21.3) 0.740 (18.8) 0.310 (7.62) 0.290 (7.36) FIG. 10 GBPC-W 1.135 (28.8) Hole for #10 Screw 0.220 (5.59) DIA. 0.200 (5.08) 1.115 (28.3) 0.732 (18.6) 0.692 (17.6) 0.24 (6.0) 0.18 (4.6) 1.135 (28.8) 1.115 (28.3) 0.732 (18.6) 0.692 (17.6) 0.24 (6.0) 0.18 (4.6) 0.470 (11.9) 0.430 (10.9) 0.50 (12.7) 0.44 (11.7) 0.042 (1.07) 0.038 (0.97) DIA. 1.25 (31.8) MIN. 0.310 (7.62) 0.290 (7.36) Dimensions in inches and (millimeters) NOTES: (1) Corrosion resistant terminals designed with 0.25” female quick connectors for wrap or snap-on (2) A thin film of silicone thermal compound is recommended between the bridge case and mounting surface for improved thermal conduction