GF1A

GF1A THRU GF1M SURFACE MOUNT GLASS PASSIVATED JUNCTION RECTIFIER Reverse Voltage - 50 to 1000 Volts * E D DO-214BA Forward Current - 1.0 Ampere FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ Ideal for surface mount automotive applications ♦ High temperature metallurgically bonded construction ♦ Glass passivated cavity-free junction ♦ Capable of meeting environmental standards of MIL-S-19500 ♦ Built-in strain relief ♦ Easy pick and place ♦ High temperature soldering guaranteed: 450°C/5 seconds at terminals ♦ Complete device submersible temperature of 265°C for 10 seconds in solder bath E P A T N 0.060 (1.52) 0.040 (1.02) T 0.187 (4.75) 0.167 (4.24) 0.0105 (0.27) 0.0065 (0.17) 0.118 (3.00) 0.106 (2.69) 0.108 (2.74) 0.098 (2.49) 0.060 (1.52) 0.030 (0.76) 0.152 TYP. 0.006 0.226 (5.74) 0.196 (4.98) 0.114 (2.90) 0.094 (2.39) Patent No. 3,996,602, brazed-lead assembly by Patent No. 3,930,306 and lead forming by Patent No. 5,151,846 ® *Glass-plastic encapsulation technique is covered by Dimensions in inches and (millimeters) MECHANICAL DATA Case: JEDEC DO-214BA molded plastic over glass body Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.0048 ounces, 0.120 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS GF1A GA GF1B GB GF1D GD GF1G GG GF1J GJ GF1K GK GF1M GM UNITS Device marking code Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TL=125°C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage at 1.0A Maximum DC reverse current at rated DC blocking voltage Typical reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Typical thermal resistance (NOTE 3) Operating junction and storage temperature range TA=25°C TA=125°C VRRM VRMS VDC I(AV) 50 35 50 100 70 100 200 140 200 400 280 400 1.0 600 420 600 800 560 800 1000 700 1000 Volts Volts Volts Amp IFSM VF IR trr CJ RΘJA RΘJL TJ, TSTG 30.0 1.10 5.0 50.0 2.0 15.0 80.0 26.0 -65 to +175 1.20 Amps Volts µA µs pF °C/W °C NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied VR=4.0 Volts (3) Thermal resistance from junction to ambient and from junction to lead P.C.B. mounted on 0.2 x 0.2” (5.0 x 5.0mm) copper pad areas 4/98 RATINGS AND CHARACTERISTIC CURVES GF1A THRU GF1M FIG. 1 - FORWARD CURRENT DERATING CURVE AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 60 HZ RESISTIVE OR INDUCTIVE LOAD P.C.B. MOUNTED on 0.2 x 0.2” (5.0 x 5.0mm) COPPER PAD AREAS FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 30 PEAK FORWARD SURGE CURRENT, AMPERES 1.0 25 20 15 10 5.0 0 TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 0.5 0 100 110 120 130 140 150 160 175 LEAD TEMPERATURE, °C 1 10 NUMBER OF CYCLES AT 60 HZ 100 FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, MICROAMPERES FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 10 INSTANTANEOUS FORWARD CURRENT, AMPERES 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 1 TJ=100°C 1 0.1 0.1 TJ=25°C 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 5 - TYPICAL JUNCTION CAPACITANCE TJ=25°C f=1.0 MHZ Vsig=50mVp-p FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE (°C/W) 30 JUNCTION CAPACITANCE, pF 100 MOUNTED ON 0.20 x 0.27” (5 x 7mm) COPPER PAD AREAS 10 10 1 1 1 10 REVERSE VOLTAGE, VOLTS 100 0.1 0.01 0.1 1 t, PULSE DURATION, sec 10 100