GI1103

GI1101 THRU GI1104 GLASS PASSIVATED FAST EFFICIENT RECTIFIER Reverse Voltage - 50 to 200 Volts * DO-204AP Forward Current - 2.5 Amperes FEATURES ♦ High temperature metallurgically bonded construction ♦ Glass passivated cavity-free junction ♦ Superfast recovery time for high efficiency ♦ Low forward voltage, high current capability ♦ Capable of meeting environmental standards of MIL-S-19500 ♦ Hermetically sealed package ♦ Low Leakage ♦ High surge capability ♦ High temperature soldering guaranteed: 350°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension N T E E 0.034 (0.86) 0.028 (0.71) DIA. 1.0 (25.4) MIN. P A T D 0.240 (6.1) MAX. 0.150 (3.8) 0.100 (2.5) DIA. 1.0 (25.4) MIN. MECHANICAL DATA Case: JEDEC DO-204AP solid glass body Terminals: Plated axial leads, solderable per MIL-STD 750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.02 ounce, 0.56 gram Dimensions in inches and (millimeters) *Brazed lead assembly is covered by Patent No. 3,930,306 MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS GI1101 GI1102 GI1103 GI1104 UNITS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current 0.375" (9.5mm) lead length (SEE FIG.1) Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) at rated TL Maximum instantaneous forward voltage at 2.0A Maximum DC reverse current at rated DC blocking voltage Maximum reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Typical thermal resistance (NOTE 1) (NOTE 4) VRRM VRMS VDC I(AV) 50 35 50 100 70 100 2.5 150 105 150 200 140 200 2.0 Volts Volts Volts Amps IFSM 0.975 2.0 50.0 25.0 50.0 1.25 (NOTE 5) Amps VF Volts µA ns pF °C/W TA=25°C TA=100°C IR trr CJ RΘJA RΘJL TJ, TSTG 10.0 200.0 50.0 45.0 65.0 20.0 Operating junction and storage temperature range -65 to +175 -65 to +150 °C NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient at 0.375" (9.5mm) lead length and mounted on P.C.B. with 0.5 x 0.5” (12 x 12mm) copper pads (4) Thermal resistance from junction to lead at 0.375" (9.5mm) lead length with both leads attached to heat sinks (5) Tested at IF=1.0A 4/98 RATINGS AND CHARACTERISTIC CURVES GI1101 THRU GI1104 FIG. 1 - MAXIMUM FORWARD CURRENT DERATING CURVE FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 3.5 AVERAGE FORWARD RECTIFIED CURRENT, AMPERES RESISTIVE OR INDUCTIVE LOAD 60 PEAK FORWARD SURGE CURRENT, AMPERES 3.0 2.5 2.0 1.5 1.0 0.5 0 0 GI1101 - GI1103 0.8 x 0.8 x 0.04" THK (20 x 20 x 1.0mm) COPPER HEATSINKS 50 40 30 20 10 0 1 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) at RATED TL GI1104 TL L 0.375" (9.5mm) LEAD LENGTH 25 50 75 100 125 150 175 10 NUMBER OF CYCLES AT 60 HZ 100 LEAD TEMPERATURE, °C FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS 50 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES 1,000 INSTANTANEOUS FORWARD CURRENT, AMPERES 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 100 TJ=125°C 10 1 TJ=100°C 1 0.1 0.1 TJ=25°C 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0.01 0 20 40 60 80 100 INSTANTANEOUS FORWARD VOLTAGE, VOLTS PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 5 - TYPICAL JUNCTION CAPACITANCE 90 JUNCTION CAPACITANCE, pF 75 60 45 30 15 0 0.1 1 TJ=25°C f=1.0 MHZ Vsig=50mVp-p 10 100 REVERSE VOLTAGE, VOLTS