GI2404

GI2401 THRU GI2404 GLASS PASSIVATED PLASTIC RECTIFIER Reverse Voltage - 50 to 200 Volts TO-220AB 0.185 (4.70) 0.175 (4.44) 0.154 (3.91) DIA. 0.148 (3.74) 0.055 (1.39) 0.045 (1.14) Forward Current - 16.0 Amperes FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ Dual rectifier construction, positive centertap ♦ Glass passivated chip junctions ♦ Low power loss ♦ High surge capability ♦ Superfast recovery times for high efficiency ♦ High temperature soldering guaranteed: 250°C, 0.16" (4.06mm) from case for 10 seconds 0.415 (10.54) MAX. 0.370 (9.40) 0.360 (9.14) 0.113 (2.87) 0.103 (2.62) 0.145 (3.68) 0.135 (3.43) 0.560 (14.22) 0.530 (13.46) 0.410 (10.41) 0.390 (9.91) PIN 2 0.635 (16.13) 0.625 (15.87) 1 0.160 (4.06) 0.140 (3.56) 0.560 (14.22) 0.530 (13.46) 3 0.350 (8.89) 0.330 (8.38) 1.148 (29.16) 1.118 (28.40) 0.110 (2.79) 0.100 (2.54) MECHANICAL DATA Case: JEDEC TO-220AB molded plastic body over passivated chips Terminals: Plated lead solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Mounting Torque: 5 in. - lbs. max. Weight: 0.08 ounce, 2.24 grams 0.105 (2.67) 0.095 (2.41) 0.037 (0.94) 0.027 (0.68) 0.105 (2.67) 0.095 (2.41) 0.205 (5.20) 0.195 (4.95) 0.022 (0.56) 0.014 (0.35) PIN 1 PIN 3 PIN 2 CASE Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS . Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS GI2401 GI2402 GI2403 GI2404 UNITS Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TC=125°C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) at TC=125°C Maximum instantaneous forward voltage per leg at: IF=4A, TJ=25°C IF=8A, TJ=25°C IF=4A, TJ=100°C IF=8A, TJ=100°C Maximum DC reverse current at rated DC blocking voltage Typical junction capacitance per leg (NOTE 2) Typical thermal resistance per leg (NOTE 3) Operating junction and storage temperature range TC=25°C TC=100°C VRRM VRMS VDC I(AV) 50 35 50 100 70 100 16.0 150 105 150 200 140 200 Volts Volts Volts Amps IFSM 125.0 Amps VF 0.975 0.900 0.800 0.895 50.0 150.0 35.0 85.0 16.0 2.2 -65 to +150 5.0 500.0 Volts IR trr CJ RΘJA RΘJC TJ, TSTG µA ns pF °C/W °C Maximum reverse recovery time per leg (NOTE1) NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to case and from junction to ambient per leg mounted on heatsink 4/98 RATINGS AND CHARACTERISTICS CURVES GI2401 THRU GI2404 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG PEAK FORWARD SURGE CURRENT, AMPERES FIG. 1 -FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT, AMPERES 20 INFINITE HEAT SINK, TC 150 125 100 75 50 25 0 1 RESISTIVE OR INDUCTIVE LOAD 16 12 8.0 AMBIENT AIR RATING, TA 8.3ms SINGLE HALF SINE WAVE (JEDEC Method) TC=125°C 4.0 0 0 50 100 150 TEMPERATURE, °C 10 NUMBER OF CYCLES AT 60 HZ 100 FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 80 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES FIG.3 -TYPICAL REVERSE CHARACTERISTICS PER LEG 100 INSTANTANEOUS FORWARD CURRENT, AMPERES TJ=125°C 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 10 TJ= 125 °C 1 TJ=1 00°C 1 0.1 0.1 TJ=25°C 0.01 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 0.01 0 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG 1,000 JUNCTION CAPACITANCE, pF TJ=25°C f=1.0 MHZ Vsig=50mVp-p 100 10 0.1 1 10 100 REVERSE VOLTAGE, VOLTS