GI506

GI500 THRU GI510 GENERAL PURPOSE PLASTIC RECTIFIER Reverse Voltage - 50 to 1000 Volts DO-201AD Forward Current - 3.0 Amperes FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High surge current capability ♦ Typical IR less than 0.1µA ♦ Construction utilizes void-free molded plastic technique ♦ High current operation of 3.0 Amperes at TA=95°C with no thermal runaway ♦ High temperature soldering guaranteed: 250°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension 1.0 (25.4) MIN. 0.210 (5.3) 0.190 (4.8) DIA. 0.375 (9.5) 0.285 (7.2) 0.052 (1.32) 0.048 (1.22) DIA. 1.0 (25.4) MIN. MECHANICAL DATA Case: JEDEC DO-201AD molded plastic body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.04 ounce, 1.1 grams Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS GI 500 GI 501 GI 502 GI 504 GI 506 GI 508 GI 510 UNITS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current 0.375" (9.5mm) lead length at TA= 95°C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage TJ= 25°C at 9.4A TJ=175°C Maximum DC reverse current at rated DC blocking voltage Typical junction capacitance (NOTE 1) Typical reverse recovery time (NOTE 2) Typical thermal resistance (NOTE 3) Operating junction temperature range Storage temperature range TA=25°C TA=100°C VRRM VRMS VDC I(AV) 50 35 50 100 70 100 200 140 200 400 280 400 3.0 600 420 600 800 560 800 1000 700 1000 Volts Volts Volts Amps IFSM 100.0 1.1 1.0 5.0 50.0 28.0 2.0 20.0 5.0 -50 to +150 -50 to +175 Amps VF IR CJ trr RΘJA RΘJL TJ TSTG Volts µA pF µs °C/W °C °C NOTES: (1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (2) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (3) Thermal resistance from junction to ambient and from junction to lead at 0.375” (9.5mm) lead length, P.C.B. mounted with 0.8 x 0.8” (20 x 20mm) copper heatsinks 4/98 RATINGS AND CHARACTERISTIC CURVES GI500 THRU GI510 AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 FIG. 1 - FORWARD CURRENT DERATING CURVE L=0.25” (6.3mm) FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 200 L = 0.31”(7.9mm) TL = BOTH LEADS to HEAT SINK MOUNTED LENGTHS (L) as SHOWN 60HZ RESISTIVE OR INDUCTIVE LOAD PEAK FORWARD CURRENT, AMPERES TJ=150°C 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) NON-REPETITIVE L= 0.50” (12.7mm) 100 REPETITIVE 0 20 TA=AMBIENT TEMPERATURE 0.375 (9.5mm) LEAD LENGTH P.C.B. MOUNTING 10 100 120 140 160 40 60 80 1 10 NUMBER OF CYCLES AT 60 HZ 100 TEMPERATURE, °C FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 100 INSTANTANEOUS FORWARD CURRENT, AMPERES 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE INSTANTANEOUS REVERSE CURRENT, MICROAMPERES 10 TJ=150°C 1 1 TJ=100°C 0.1 TJ=25°C 0.1 0.01 0 20 40 60 80 100 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 PERCENT OF RATED PEAK REVERSE VOLTAGE,% INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE 100 JUNCTION CAPACITANCE, pF TJ=25°C f=1.0 MHz Vsig=50mVp-p TRANSIENT THERMAL IMPEDANCE, °C/W FIG. 5 - TYPICAL JUNCTION CAPACITANCE 100 10 10 1 1 0.1 1 10 100 0.1 0.01 0.1 1 t, PULSE DURATION, sec. 10 100 REVERSE VOLTAGE, VOLTS