GI826

GI820 THRU GI828 FAST SWITCHING PLASTIC RECTIFIER Reverse Voltage - 50 to 800 Volts Case Style P600 Forward Current - 5.0 Amperes FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High surge current capability ♦ High forward current operation ♦ Fast switching for high efficiency ♦ Construction utilizes void-free molded plastic technique ♦ Uniform molded body ♦ High temperature soldering guaranteed: 250°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension 1.0 (25.4) MIN. 0.360 (9.1) 0.340 (8.6) 0.360 (9.1) 0.340 (8.6) 0.052 (1.32) 0.048 (1.22) DIA. 1.0 (25.4) MIN. MECHANICAL DATA Case: Void-free molded plastic body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.07 ounce, 2.1grams Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS GI820 GI821 GI822 GI824 GI826 GI828 UNITS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum non-repetitive peak reverse voltage Maximum average forward rectified current 0.375" (9.5mm) lead length at T A=55°C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage at 5.0A TJ= 25°C at 15.7A TJ=150°C Maximum reverse current at rated DC blocking voltage TA= 25°C TA=100°C VRRM VRMS VDC VRSM I(AV) 50 35 50 75 100 70 100 150 200 140 200 250 5.0 400 280 400 450 600 420 600 650 800 560 800 880 Volts Volts Volts Volts Amps IFSM 300.0 Amps VF 1.10 1.05 10.0 1.0 300.0 200.0 2.0 10.0 -50 to +150 Volts µA mA pF ns Amps °C/W °C IR CJ trr IRM(REC) RΘJA TJ, TSTG Typical junction capacitance (NOTE 1) Maximum reverse recovery time (NOTE 2) Maximum reverse recovery current (NOTE 2) Typical thermal resistance (NOTE 3) Operating junction and storage temperature range NOTES: (1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (2) Reverse recovery test conditions: IF=1.0A, VR=30V, di/dt=50A/µs, and Irr=10% IRM for measurement of trr (3) Thermal resistance from junction to ambient at 0.375” (9.5mm) lead length, with both leads equally to heat sink 4/98 RATINGS AND CHARACTERISTIC CURVES GI820 THRU GI828 FIG.1 - FORWARD CURRENT DERATING CURVE 7.0 AVERAGE FORWARD CURRENT, AMPERES AVERAGE FORWARD CURRENT, AMPERES FIG. 2 - FORWARD CURRENT DERATING CURVE 6.0 5.0 4.0 3.0 2.0 1.0 0 20 Ipk/IAV=π CAPACITIVE LOADS 5.0 I(pk) 10 I(AV) 20 20 16 L=0 RESISTIVE OR INDUCTIVE LOAD L= LEAD LENGTH 1.6” x 1.6” x 0.04” (40mm x 40mm x 1mm) COPPER HEATSINK 12 L=0 .25” .12 ”(3. 2m m) 8.0 4.0 0 75 (6.3 mm L=0.3 ) 75”(9.5 mm) ) L=0.62”( 1.1 x 1.1” (30 x 30mm) COPPER PADS 15.9mm 40 60 80 100 120 140 160 180 85 95 105 115 125 135 145 155 165 175 LEAD TEMPERATURE, °C AMBIENT TEMPERATURE, °C FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, AMPERES 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 100 INSTANTANEOUS FORWARD CURRENT, AMPERES TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 400 350 TA=25°C 300 250 TJ=125°C 10 200 150 100 1 1 10 NUMBER OF CYCLES AT 60 Hz 100 0.1 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 5 - TYPICAL REVERSE CHARACTERISTICS FIG. 6 - TYPICAL THERMAL RESISTANCE 10 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES TJ=100°C 25 RΘJL, THERMAL RESISTANCE FROM JUNCTION TO LEAD, °C/W L= LEAD LENGTH 20 15 10 5.0 0 1 TJ=50°C 0.1 TJ=25°C 0.01 0 20 40 60 80 100 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 PERCENT OF RATED PEAK REVERSE VOLTAGE, % EQUAL LEAD LENGTHS TO HEAT SINK, INCHES