GL34D

GL34A THRU GL34J SURFACE MOUNT GLASS PASSIVATED FAST SWITCHING JUNCTION RECTIFIER Reverse Voltage - 50 to 600 Volts * D DO-213AA Forward Current - 0.5 Ampere FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ For surface mount applications ♦ High temperature metallurgically bonded construction ♦ Glass passivated cavity-free junction ♦ Capable of meeting environmental standards of MIL-S-19500 ♦ Fast switching for high efficiency ♦ High temperature soldering guaranteed: 450°C/5 seconds at terminals. Complete device submersible temperature of 260°C for 10 seconds in solder bath N T E SOLDERABLE ENDS 1st BAND 2nd BAND P A T E D2 D1= 0.066 0.060 (1.676) (1.524) 0.022 (0.559) 0.016 (0.406) 0.145 (3.683) 0.131(3.327) 1st band denotes type and polarity 2cnd band denotes voltage type D2 = D1 + 0 - 0.008 (0.20) MECHANICAL DATA Case: JEDEC DO-213AA molded plastic over glass body Terminals: Plated terminals, solderable per MIL-STD-750, Method 2026 Polarity: Two bands indicate cathode-end - 1st band denotes device type and 2nd band denotes repetitive peak reverse voltage rating Mounting Position: Any Weight: 0.0014 ounce, 0.036 gram Dimensions in inches and (millimeters) *Glass-plastic encapsulation technique is covered by Patent No. 3,996,602 and brazed-end cap assembly by Patent No. 3,930,306 ® MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. Standard recovery device: first band is white SYMBOLS GL34A GL34B GL34D GL34G GL34J Polarity color bands (2nd Band) Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TT=75°C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage at 0.5A Maximum DC reverse current at rated DC blocking voltage TA=25°C TA=125°C VRRM VRMS VDC I(AV) Gray 50 35 50 Red 100 70 100 Orange 200 140 200 0.5 Yellow 400 280 400 Green 600 420 600 Volts Volts Volts Amp IFSM VF IR IR(AV) trr CJ RΘJA RΘJT TJ, TSTG 10.0 1.2 5.0 50.0 30.0 1.5 4.0 150.0 70.0 -65 to +175 1.3 Amps Volts µA µA µs pF °C/W °C Maximum full load reverse current, full cycle average at TA=55°C Typical reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Maximum thermal resistance (NOTE 3) (NOTE 4) Operating junction and storage temperature range NOTES: (1) Reverse recovery test conditions IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient, 0.2 x 0.2” (5.0 x 5.0mm) copper pads to each terminal (4) Thermal resistance from junction to terminal, 0.2 x 0.2” (5.0 x 5.0mm) copper pads to each terminal 4/98 RATINGS AND CHARACTERISTIC CURVES GL34A THRU GL34J FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, AMPERES FIG. 1 - FORWARD CURRENT DERATING CURVE AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 0.5 0.4 0.3 0.2 0.1 0 25 10 8.0 6.0 4.0 2.0 0 60 HZ RESISTIVE OR INDUCTIVE LOAD TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 1 10 NUMBER OF CYCLES AT 60 HZ 100 50 75 100 125 150 175 TERMINAL TEMPERATURE, °C FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, MICROAMPERES FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 10 INSTANTANEOUS FORWARD CURRENT, AMPERES 10 1 TJ=100°C 1 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 0.1 0.1 TJ=25°C 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 5 - TYPICAL JUNCTION CAPACITANCE 30 JUNCTION CAPACITANCE, pF TJ=25°C f=1.0 MHZ Vsig=50mVp-p 10 1 1 10 REVERSE VOLTAGE, VOLTS 100