GP20G

GP20A THRU GP20J GLASS PASSIVATED JUNCTION RECTIFIER Reverse Voltage - 50 to 600 Volts * D Case Style GP20 Forward Current - 2.0 Amperes FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High temperature metallurgically bonded construction ♦ Glass passivated cavity-free junction ♦ Capable of meeting environmental standards of MIL-S-19500 ♦ 2.0 Ampere operation at TA= 55°C with no thermal runaway ♦ Typical IR less than 0.1µA ♦ High temperature soldering guaranteed: 350°C/10 seconds 0.375" (9.5mm) lead length, 5 lbs.(2.3kg) tension E N T E P A T 1.0 (25.4) MIN. 0.210 (5.3) 0.190 (4.8) DIA. 0.375 (9.5) 0.285 (7.2) 1.0 (25.4) MIN. 0.042 (1.07) 0.037 (0.94) DIA. MECHANICAL DATA Case: Molded plastic over glass body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Band denotes cathode end Mounting Position: Any Weight: 0.03 ounce, 0.8 gram Dimensions in inches and (millimeters) *Glass-plastic encapsulation technique is covered by Patent No. 3,996,602 and brazed-lead assembly by Patent No. 3,930,306 ® MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS GP 20A GP 20B GP 20D GP 20G GP 20J UNITS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current 0.375" (9.5mm) lead length at TA=55°C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage at 2.0A Maximum reverse current at rated DC blocking voltage Maximum full load reverse current, full cycle average 0 375" (9.5mm) lead length at TA=55°C Typical reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Typical thermal resistance (NOTE 3) Operating junction and storage temperature range VRRM VRMS VDC I(AV) 50 35 50 100 70 100 200 140 200 2.0 400 280 400 600 420 600 Volts Volts Volts Amps IFSM VF IR IR(AV) trr CJ RΘJA RΘJL TJ, TSTG 1.2 65.0 1.1 5.0 100.0 2.5 40.0 25.0 10.0 -65 to +175 Amps Volts µA µA µs pF °C/W °C NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient and from junction to lead at 0.375" (9.5mm) lead length P.C.B. mounted 4/98 RATINGS AND CHARACTERISTIC CURVES GP20A THRU GP20J FIG. 1 - FORWARD CURRENT DERATING CURVE AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 2.0 1.5 1.0 0.5 0.375"(9.5mm) LEAD LENGTH 100 PEAK FORWARD SURGE CURRENT, AMPERES 60 HZ RESISTIVE OR INDUCTIVE LOAD TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 60 40 20 0 0 25 50 75 100 125 150 175 10 1 10 NUMBER OF CYCLES AT 60 HZ AMBIENT TEMPERATURE, °C 100 FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 20 10 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES 10 INSTANTANEOUS FORWARD CURRENT, AMPERES TJ=150°C TJ=125°C 1 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 1 0.1 TJ=75°C 0.1 TJ=25°C 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % TRANSIENT THERMAL IMPEDANCE, °C/W FIG. 5 - TYPICAL JUNCTION CAPACITANCE FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE 100 JUNCTION CAPACITANCE, pF TJ=25°C f=1.0 MHZ Vsig=50mVp-p 100 10 1 10 1 10 REVERSE VOLTAGE, VOLTS 100 0.1 0.01 0.1 1 10 100 t, PULSE DURATION, sec.