RS3A

RS3A THRU RS3K SURFACE MOUNT FAST SWITCHING RECTIFIER Reverse Voltage - 50 to 800 Volts DO-214AB MODIFIED J-BEND Forward Current - 3.0 Amperes FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ For surface mount applications ♦ Low profile package ♦ Built-in strain relief, ideal for automated placement ♦ Fast switching for high efficiency ♦ Easy pick and place ♦ Glass passivated chip junction ♦ High temperature soldering: 250°C/10 seconds at terminals 0.126 (3.20) 0.114 (2.90) 0.245 (6.22) 0.220 (5.59) 0.280 (7.11) 0.260 (6.60) 0.012 (0.305) 0.006 (0.152) 0.103 (2.62) 0.079 (2.06) MECHANICAL DATA 0.060 (1.52) 0.030 (0.76) 0.320 (8.13) 0.305 (7.75) 0.008 (0.203) MAX. Dimensions in inches and (millimeters) Case: JEDEC DO-214AB molded plastic body over passivated chip Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Weight: 0.007 ounce, 0.25 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS RS3A RA RS3B RB RS3D RD RS3G RG RS3J RJ RS3K RK UNITS Device marking code Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TL=75°C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) TL=75°C Maximum instantaneous forward voltage at 2.5A Maximum DC reverse current at Rated DC blocking voltage Maximum reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Typical thermal resistance (NOTE 3) Operating junction and storage temperature range TA=25°C TA=125°C VRRM VRMS VDC I(AV) 50 35 50 100 70 100 200 140 200 3.0 400 280 400 600 420 600 800 560 800 Volts Volts Volts Amps IFSM VF IR trr CJ RΘJA RΘJL TJ, TSTG 150 100.0 1.3 10.0 250 250 60.0 50.0 15.0 -55 to +150 500 Amps Volts µA ns pF °C/W °C NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied VR=4.0 Volts (3) Thermal resistance from junction to ambient and from junction to lead mounted on P.C.B. with 0.3 x 0.3” (8.0 x 8.0mm) copper pad areas 4/98 RATINGS AND CHARACTERISTIC CURVES RS3A THRU RS3K FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT FIG. 1 - FORWARD CURRENT DERATING CURVE 3.0 AVERAGE FORWARD CURRENT, AMPERES RESISTIVE OR INDUCTIVE LOAD 150 PEAK FORWARD SURGE CURRENT, AMPERES 2.5 2.0 125 100 75 50 25 0 1 10 TL=75°C 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 1.0 P.C.B. MOUNTED 0.3 x 3.0” (8.0 x 8.0mm) COPPER PAD AREAS 0 0 50 100 150 200 100 LEAD TEMPERATURE, °C NUMBER OF CYCLES AT 60 HZ FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 100 INSTANTANEOUS FORWARD CURRENT, AMPERES 100 TJ=125°C TJ=125°C 10 TJ=25°C TJ=-40°C 1 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES PULSE WIDTH=300µs 1% DUTY CYCLE 10 TJ=75°C 1 0.1 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 INSTANTANEOUS FORWARD VOLTAGE, VOLTS TJ=25°C 0.1 FIG. 5 - TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE (°C/W) 100 MOUNTED ON 0.20 x 0.27” (5 x 7mm) COPPER PAD AREAS 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 10 1 0.1 0.01 0.1 1 t, PULSE DURATION, sec 10 100